Reddit Reddit reviews 10mm (5050) Solderless LED Light Strip Connector Extension, Multi Color RGB - 6 Inch (4 Pack) Strip to Strip Any Angle Connector - for LED Strip Light & Tape Light in Kitchens, Cabinets, Shelving & More

We found 5 Reddit comments about 10mm (5050) Solderless LED Light Strip Connector Extension, Multi Color RGB - 6 Inch (4 Pack) Strip to Strip Any Angle Connector - for LED Strip Light & Tape Light in Kitchens, Cabinets, Shelving & More. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Lighting & Ceiling Fans
Track Lighting
Track Lighting Connectors
Ceiling Light Fixtures
10mm (5050) Solderless LED Light Strip Connector Extension, Multi Color RGB - 6 Inch (4 Pack) Strip to Strip Any Angle Connector - for LED Strip Light & Tape Light in Kitchens, Cabinets, Shelving & More
RELIABLE AND EASY TO USE connection for bending your strips around a corner, extending them across a gap, or connecting them to a power supply or dimmerSOLDERLESS CONNECTION can be used by anyone. No tools or electrical experience requiredCONNECTS EASILY to a cut section of LED light strip. Simply open the clasp, make sure the strip aligns with the connector (match the positive terminals), and slide it underneath the contact prongs. Compatible with any 8mm stripsFOUR 6 INCH CONNECTORS included in packageHITLIGHTS QUALITY. Backed by a one year warranty from HitLights for peace of mind. Contact our US-based customer service team at any time for no-hassle troubleshooting and replacement or for any questions about purchasing or installation
Check price on Amazon

5 Reddit comments about 10mm (5050) Solderless LED Light Strip Connector Extension, Multi Color RGB - 6 Inch (4 Pack) Strip to Strip Any Angle Connector - for LED Strip Light & Tape Light in Kitchens, Cabinets, Shelving & More:

u/jtrias21 · 29 pointsr/buildapcsales

I've been using these HitLights LED strip for over a year, no complaints 9/10 for this price.

old setup with the LED's from last year

current setup still same kit

Edit: You might also want to pick up a strip-to-strip connector for $7 like this one so it looks cleaner along the corners but it's not necessary considering the LEDs will be hidden anyways.

u/_sch · 2 pointsr/HomeImprovement

This is the one I've been using: http://www.amazon.com/gp/product/B0040FJ27S/

There may be better and worse ones out there; honestly I don't remember how I chose that. But I have three of them and they've worked well for me.

So far I haven't run into any problems. When/if you splice the strips, obviously make sure you keep the wires in order. They sell pre-made connectors and splitters, but I didn't really use any of those. I did buy some of these connectors: http://www.amazon.com/gp/product/B006VZKSNC but all I ended up using them for was the raw wire (I cut the ends off an soldered them directly to the strips).

In the Arduino-controlled setup, I re-used the power supply that came with the strip, and just fed it through the mosfets linked above. I discareded the remote and the little controller box (well, I filed them away for potential later use).

In my application I found that the adhesive on the back of the strips didn't work very well, so I ended up taping it up with gaffer tape. That works well for me because the strip is in a recessed area you can't see unless you crane your neck to look for it. But if the strips were somewhere more visible, I'd need to look for a more elegant mounting solution.

u/phantastimal · 2 pointsr/DIY
u/Graphitetshirt · 1 pointr/DIY

Any reason you didnt just use connectors like this?

u/EliTheAsianGuy · 1 pointr/buildapcsales

The LED strips are cut-to-length at specified locations (usually indicated by scissor icons).

You can either go with an adapter or do it yourself method. If you want to use an adapter or premade connector you can use something like: 90 Degree Connector or RGB Connector. If you want to look for other products just lookup something like "RGB LED Strip Connector."

If you want to go the DIY path to route around curves or sharp 90-degree bends, you will need to cut the strips and solder them together. You'd want to use small wire, so if you maybe have a spare ethernet cord, you could use the wires found within to use as connectors.