Reddit Reddit reviews 3M Black Super Weatherstrip and Gasket Adhesive, 08008, 5 fl oz

We found 12 Reddit comments about 3M Black Super Weatherstrip and Gasket Adhesive, 08008, 5 fl oz. Here are the top ones, ranked by their Reddit score.

Automotive
Oils & Fluids
Body Repair & Restoration Chemicals
Body Repair & Restoration Adhesives
3M Black Super Weatherstrip and Gasket Adhesive, 08008, 5 fl oz
Forms flexible, waterproof bond that resists vibrationEasy to brush and spread right from the tube, saving timeResists oils, solvents, detergents and temperature changes for permanent repairsBonds to a range of surfaces including vinyl, metal, fabrics and rubber
Check price on Amazon

12 Reddit comments about 3M Black Super Weatherstrip and Gasket Adhesive, 08008, 5 fl oz:

u/nuovo_donna · 10 pointsr/Autos
u/testingapril · 4 pointsr/Homebrewing

This stuff works great: http://smile.amazon.com/gp/product/B00063X38M/

recommended by homebrewfinds, I've done several kegs with it and had no problems. Just follow the package directions, and it's set in probably 15-30 mins I think.

u/mingy · 3 pointsr/Toyota

Go to an autoparts store. Explain the seal coming off: they have a special urethane adhesive made expressly for that. I've bought in the past. This https://www.amazon.com/3M-08008-Black-Weatherstrip-Adhesive/dp/B00063X38M isn't the one I used but it is similar.

For the hydraulic lifter, they are real easy to replace, basically a clip to pry aside (at least on all my Toyotas). Here's a video https://www.youtube.com/watch?v=gphWW2P620Y for a Prius but yours is probably similar. You can un-clip the old one, bring it to the store and get a replacement (or just tell them the make and model and they'll give it to you).

Try do it yourself. Worse case you'll have to ask somebody if you can't. Its real easy.

u/Mn2511 · 2 pointsr/ft86

Read on the forums that it's usually a tail light gasket issue and applied this sealant on both gasket surfaces and that solved the issues.

3M 08008 Black Super Weatherstrip Adhesive Tube - 5 oz. https://www.amazon.com/dp/B00063X38M/ref=cm_sw_r_cp_api_w9NoxbZZS1WR8

Also even the aftermarket tail lights can have this issue with the gasket.

u/Travoli · 1 pointr/travel

It's really easy and inexpensive to make them. Check this out. Instead of sewing them, I used 3M Weatherstrip Adhesive and magnetic strips.

u/pacoliketaco · 1 pointr/DIY

This stuff: https://www.amazon.com/3M-08008-Black-Weatherstrip-Adhesive/dp/B00063X38M

works great for rubber to metal. I use it a lot at work for small little things.

u/cornrichard · 1 pointr/motorcycles
u/11lariat · 1 pointr/Trucks

I've always used 3M weatherstripping adhesive. Amazon carries it, but I usually get it from my local parts place.

http://www.amazon.com/3M-08008-Black-Weatherstrip-Adhesive/dp/B00063X38M

Not sure what to recommend for the back panels. Silicone caulk isn't going to be super durable though.

u/Liluben · 1 pointr/DelSol

Swapped my 93's seals for some off a 96. Use lots of lube where the seals sit and on top of the seals to make sure they dont dry out on you and crack.

Get this 3M 08008 Black Super Weatherstrip Adhesive to glue down the corners on the seals where the factory stuff was. This also works to glue the rubber together wherever theres a rip or crack. 10/10 product

https://www.amazon.com/dp/B00063X38M/ref=cm_sw_r_cp_apa_KwHFAbMDWF6RS

u/reboticon · 1 pointr/MechanicAdvice

What I do when I have an actual gasket I am worried about moving is use a product by 3m called Weatherstrip adhesive, lay the gasket on it and then stick the bolts through and let it sit for 5-10 minutes. Its not thick like RTV its just an adhesive so for tricky installs it is super helpful. You may not need it at all, just a handy tip.