Reddit Reddit reviews Aeon Labs DSC18103-ZWUS,White,US,AL001 Aeotec Z-Wave Micro Smart Energy Switch, 2nd Edition, White, Small

We found 28 Reddit comments about Aeon Labs DSC18103-ZWUS,White,US,AL001 Aeotec Z-Wave Micro Smart Energy Switch, 2nd Edition, White, Small. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Electrical Equipment
Electrical Switches
Dimmer Switches
Electrical Wall Switches
Aeon Labs DSC18103-ZWUS,White,US,AL001 Aeotec Z-Wave Micro Smart Energy Switch, 2nd Edition, White, Small
Low cost switch to enable remote control for existing in-wall switchReport immediate wattage consumption or kwh energy usage over a period of timeSupport Z-Wave Explorer frames. Repeat Z-Wave messageZ-wave certification Number:zc08-12090006
Check price on Amazon

28 Reddit comments about Aeon Labs DSC18103-ZWUS,White,US,AL001 Aeotec Z-Wave Micro Smart Energy Switch, 2nd Edition, White, Small:

u/exigence · 5 pointsr/homeautomation

This would do it: http://amzn.com/B00JWVNH4Y
And so would this: http://amzn.com/B008VWAPU4

u/mankyd · 5 pointsr/homeautomation

They still function like regular light switches. You can control them manually via the wall or remotely.

Note that all ZWave switches that I've seen basically amount to push buttons instead of the typical rocker that most homes use. That is to say, they have a physical switch with both and on and an off, but the switch doesn't physically move to indicate whether it's on or off. They usually have an led built into them that shows this.

If you want to keep your existing switches, check out something like Aeotec's micro-switches: http://www.amazon.com/gp/product/B008VWAPU4/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1. You install these behind your existing wall switches. Once you do that, your existing switches continue to work the same as before, and you can control them remotely.

u/CynicallySane · 3 pointsr/smarthome

SmartThings and Alex work very well together. Not to mention SmartThings automation is second to none as far as I have experienced with other hubs. This prevents you from having all those apps as you mentioned. All you have to do is add zwave or zigbee devices to your hub and you can control them from one place.
In your case, especially with the outside lights, I would just install one of these Aeontec microswitches. They come in dimmers too. You can hide them in the walls and your switches still work just as they did before, with the exception that you can now control them wirelessly. Just be sure to watch your draw. A lot of outdoor flood lights might be too much wattage for them. I installed a Lutron Caseta switch and hub for my father and quickly brushed up against the 650 Watt limit of those switches with all his outdoor flood lights. I'll be honest I don't know the limit of these switches and I can't find it on Aeontec's website, but you should be fine bellow 700 watts per switch.
With SmartThings you can set up timers for devices, link them to motion detectors, and even check on their power consumption if you have the right kind of switch.

u/unreasonablymundane · 3 pointsr/smarthome

Virtually all smart switches require a neutral (typically a white wire). Some dimmers only require 3 connections (live, load, and ground).

Smart bulbs are the easiest solution, but the most expensive (and annoying) in the long term (if the switch is off you can't control the light from other devices)

For using smart switches running an additional wire from the switch box to the neutral bus in the breaker box is an option but is usually the most labor intensive option. For other options you need to identify how the switches were wired. There are 3 common ways:

  1. Best case: there are 2 sets of wires in the switch box, and 1 set of wires in the load box. This requires no new wiring you can simply install the smart switch
  2. This are 2 black wires in the switch box (and possibly ground wire(s)), and 1 set of wires in the load box. In this case the builder likely cut the black wire and ran it into the box and the neutral is uncut behind the switch box. In this case you can remove the box cut the remaining wires and run all the wires into the box.
  3. There is 1 full set of wires (black, white, and ground) in the switch box and 2 sets of wires in the load box, there are 2 options here, 1. rerun the wires between the switch and load boxes with 3 conductor wire (black, red, white, and ground) black as live, red as load, white as neutral, or 2. use a micro switch like: https://www.amazon.com/Aeon-Labs-DSC18103-ZWUS-White-AL001/dp/B008VWAPU4/ in the load box.

    Hopefully that helps.
u/CookVegasTN · 2 pointsr/Ring

SmartThings home automation hub:

https://www.smartthings.com/

This is the module I wired into the box with my doorbell transformer:

https://smile.amazon.com/gp/product/B008VWAPU4/

​

In the SmartThings app on my phone, I can turn devices off and on remotely. Could even schedule a weekly reboot if I wanted to.

u/Quasmo · 2 pointsr/electricians

My wife burnt our counter top in our bathroom. I put in an outlet with this.

I have a controller let me know if it is consuming energy. If it consumes energy for greater than 30 minutes, I turn the outlet off.

u/BreakfastBeerz · 2 pointsr/homeautomation

Look for in-wall micro relays like these. You use your existing switches. You pull the load wire off the existing switch and put it on the relay, then the load from the switch goes into the relay and acts as a trigger.

u/saunjay1 · 2 pointsr/homeautomation

Perhaps add a USB Z-stick and then use a z-wave based light switch? Or even one of those Aeon Labs z-wave micro smart switches that can go behind your existing dumb switches if your wife doesn't like the look of any other switch.

u/niedejb · 2 pointsr/homeautomation

Micro zwave switch in the gang box for the switch or at the light.

Switch interrupts the "hot" wire to the light.

Put the HA controller on a schedule to be off from bedtime til morning.

Switch will work normally at all other times.

Aeon Labs DSC18103-ZWUS,White,US,AL001 Aeotec Z-Wave Micro Smart Energy Switch, 2nd Edition, White, Small https://www.amazon.com/dp/B008VWAPU4/ref=cm_sw_r_cp_apa_2H-Nzb7KB7F84

u/CountLippe · 2 pointsr/homeautomation

Given it's an old home, how much renovation you can do? A past home I've owned was heritage listed, so small installations were the most I could achieve - that brought me to Z-Wave (wireless), a hub (Vera at the time), and in-wall micro controllers from Aeotec http://www.amazon.com/Aeon-Labs-Aeotec-Edition-DSC18103-ZWUS/dp/B008VWAPU4

u/--bohica-- · 2 pointsr/homeautomation

GE makes a toggle-style switch, which is what I imagine you have in your home: https://www.lowes.com/pd/GE-Z-Wave-15-amp-Single-Pole-3-way-Wireless-White-Toggle-Indoor-Light-Switch/1000241625

You could also purchase "micro switches" that would go behind your regular ("dumb") switch and add the smart capability: https://www.amazon.com/Aeon-Labs-DSC18103-ZWUS-White-AL001/dp/B008VWAPU4

u/eoppie · 2 pointsr/homeautomation

Do you have an existing z-wave system at all? If you wanted to do so in the future, and not replace the dimmer, you could wire in an in-line dimmer (assuming the fixtures are dimable) and then put in a wireless switch that is tied to the z-wave modules.

http://www.amazon.com/Aeon-Labs-Aeotec-Z-Wave-Edition/dp/B008VWAPU4/ref=sr_1_2?ie=UTF8&qid=1406580706&sr=8-2&keywords=aeotec

http://www.smarthome.com/59373/GE-45631-Z-Wave-Wireless-Keypad-Controller/p.aspx

u/Rob3E · 1 pointr/winkhub

Also I'm guessing something like this would partially solve your problem: https://www.amazon.com/gp/product/B008VWAPU4/

The Relay could link up to two of your switches and the micro switch to the third.

Of course the problem with any of these solutions is that you will only end up with two, physical switches. Whichever switch you do not connect to the relay should be something you don't mind activating primarily through the Relay touchscreen, your phone app, or, better yet, schedules and robots.

u/czrabode · 1 pointr/Abode

If I were you, I would go with Aeon Labs Z Wave Smart Energy Switch . They are cheap, hides behind regular light switches, and works flawlessly with Abode.

u/degorius · 1 pointr/homeassistant

ive got some of these that work great with existing switches and their faceplates and are about the same cost as whole new switches.

u/Immatix · 1 pointr/HomeNetworking

You could look into products utilizing Z-Wave. There's a few modules that can be placed into a box behind switches or above light fixtures, like potentially this one. But you'd still need a Z-Wave controller, something like the SmartThings Hub, perhaps.

EDIT: Here's another Z-Wave wire-in switch. There are even motion sensors like this one and other things that speak Z-Wave.

u/cleansweep9 · 1 pointr/homeautomation

You could always shove an Aeotec Microswitch behind a standard wall outlet.

u/bosshauss · 1 pointr/SmartThings

https://www.amazon.com/dp/B008VWAPU4/ref=cm_sw_r_cp_apa_fBzqybV7TXXRH

This will make a standard plug z wave. You can't control each plug individually but should do the trick.

u/SkyJedi · 1 pointr/SmartThings

One problem I had with smart outlets is that one one of the plugs is controlled by the switch, the other is just on 100% of the time.

In my use case, paranoia over leaving the hair curler plugged in, that down fall was two much. Sure I could see the outlet was off but I had no idea if the device was plugged into the right outlet.

My solution was this little guy
Aeon Labs DSC18103-ZWUS,White,US,AL001 Aeotec Z-Wave Micro Smart Energy Switch, 2nd Edition, White, Small https://www.amazon.com/dp/B008VWAPU4/ref=cm_sw_r_cp_apa_fBzqybV7TXXRH

Fits behind the standard outlet and turns the entire thing into a switch.

I'm also thinking this might be a good thing to add to a couple more outlets for Christmas lights

u/chasonreddit · 1 pointr/googlehome

I think something like this:

https://www.amazon.com/Aeon-Labs-DSC18103-ZWUS-White-AL001/dp/B008VWAPU4

would work for you. You can keep your existing switches even. This is assuming you have enough room behind the existing switch in the gang box. You'll need a hub like a smart things, but previous comments seem to show you are alright with that.

Personally, I love the idea of the old style edison bulbs and fixtures. This would allow you to do it with no visible changes at all.

u/AdamJacobMuller · 1 pointr/HVAC

How does your blower fan connect to power, hard wired I assume?

this meter will do it, but you need (some) infrastructure to be able to collect/log the data depending on what you want.

Once you have meter(s) like that you can do cool things with them though.

u/IKROWNI · 1 pointr/homeassistant

Since you have a metal box it won't work like that. I would probably suggest something like this maybe.

https://www.amazon.com/Aeon-Labs-DSC18103-ZWUS-White-AL001/dp/B008VWAPU4

Maybe you could place it inline somewhere closer to your network. Not sure on the ratings though.

u/thornierbird · 1 pointr/smarthome

Look for z wave micro switches. They wire in and fit behind the switch. Or you can enlarge the hole and retrofit a 2 gang remodel box.

Either option is similar in work and wire expertise. For the box you will just need a little slack in the wires or to use wire nuts and extend them, also you will need to cut a larger hole in the drywall. If you can handle wiring a light switch diy, then either option is doable.

The other option is smart bulbs. Hue bulbs can be controlled by a smartthings hub directly.

u/afghanninjacat · 1 pointr/smarthome

Are you running a hub? You could use a normal bulb and go this route: http://www.amazon.com/Aeon-Labs-DSC18103-ZWUS-White-AL001/dp/B008VWAPU4

u/_Something-Clever_ · 1 pointr/SmartThings

You might try a normal switch connected to an
Aeon Labs Z-Wave Micro Smart Energy Switch
https://www.amazon.com/dp/B008VWAPU4/ref=cm_sw_r_cp_api_0gD-zbVX154GH

Turns your dumb switch smart :)

There's also a dimmer module:
https://www.amazon.com/dp/B00IRI1CEK/ref=cm_sw_r_cp_api_PiD-zbWY6WYJM

u/wietoolow · 0 pointsr/HomeImprovement

You can do this with home automation stuff. You'd need a Z-Wave or Zigbee home controller and then one of these.