Reddit reviews ANCEL AD310 Classic Enhanced Universal OBD II Scanner Car Engine Fault Code Reader CAN Diagnostic Scan Tool-Black
We found 18 Reddit comments about ANCEL AD310 Classic Enhanced Universal OBD II Scanner Car Engine Fault Code Reader CAN Diagnostic Scan Tool-Black. Here are the top ones, ranked by their Reddit score.
Classic design, fast scan and clear trouble codes, even a beginner can use this unit to read the error code, find out what the problem is and perhaps fix it. Save money and time.Works on MOST 1996 US-Based, 2000 EU-Based and Asian cars, and newer OBD II & CAN domestic or import vehicles. Supports English, German, French, Spanish, Finnish, Dutch, Russian and Portuguese.Easily determines the cause of the check engine light. I/M monitor readiness test, turn off the MIL (check engine light) as well as view freeze frame data. Read hard (memory) / pending (intermittent) and historic codes and show definitions.The AD310 scanner is well built with a large LCD display (128 x 64 pixel) that has white backlight and contrast adjustment, indicates test results directly. No need any Batteries or Charger, gets the power directly from the OBDII Data Link Connector in your vehicle.It's equipped with a 2. 5 feet long cable and made of a very thick flexible insulator. There are 4 buttons on AD310. The Up and Down button for scrolling the menu, the Enter and Exit button allow for navigation back and entering menu.
No problem, actually to give my personal anecdote some real detail.
$35 scanner that can read live data
$155 Scanner that can read SRS and ABS
Glad to help.
Every car has there own drive cycle procedures but they all require roughly the same things. For his car yes, one of the steps was to go from 0mph to 55mph within 15 sec and maintain that speed for about 15 minutes then bring the car to a stop without using the brakes. There are a few other steps that you need to do to set all the monitors but they are usually met during normal operating conditions.
You can use an OBDII scanner to check yourself if they are set.
Also, if your check engine light comes on, Pepboys or AutoZone (or some other commercial parts store) will let you borrow their code reader (aka OBD II) which will help you figure out what the problem is. Alternatively you could buy yourself a code reader from Amazon.
This way, if you are uncomfortable fixing it yourself, you can at least get a rough estimation of what the parts actually cost to replace.
Code readers are super cheap and easy to use. I got this guy for $35 and it works perfectly. I had a faulty ECM that kept throwing engine codes. There's tons of other options too if you want more functionality, like on an Access Port.
Known as a "check engine light" or CEL as abbreviation. Depending on car you can buy a scanner to read (most likely obdii): Example https://www.amazon.com/dp/B01G5EA74I/ref=cm_sw_r_cp_apa_i3bOAbDN13N20
But most likely you will read the code and not know what to do afterwards without diligently searching on forums so you might want to just bring the car into a shop that does free code reads.
Fyi sometimes its comes on because you didnt tighten the gas cap. If you are lucky thats the only reason.
This is the code reader I bought my little brother. While it's no where near as nice as mine but it works and gets you the most basic information you could ever need on a day to day basic maintenance.
Anytime you clear the codes on your car it takes time for the system to reset itself and calibrate to show that it even exists. The best way to find out is to get a cheap code reader on Amazon and find out what it is you're failing. For me I got a new Cat on my car and it failed. I drove it 50 miles at 70mph and the next day it passed fine.
https://www.amazon.com/gp/product/B01G5EA74I/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1
This is the one that I use, be sure to NOT clear your codes, just make sure you're checking the I/M readiness.
There's no reason to freak out about it, just figure out if there's a bad sensor or something and get it fixed.
I bought the cheap one and it works fine. Gives me the data I need and can obviously clear codes.
https://www.amazon.com/gp/product/B01G5EA74I
https://www.amazon.com/gp/aw/d/B01G5EA74I/ref=mp_s_a_1_6?ie=UTF8&qid=1499231274&sr=8-6&pi=AC_SX236_SY340_QL65&keywords=obd2&dpPl=1&dpID=41vF137GMsL&ref=plSrch
Would this stuff be ok?
https://www.amazon.com/gp/product/B01G5EA74I/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
I have that. But it says no stored codes.
Car Repair PSA- For everyone here that is a car repair novice, get a diagnostic code reader. You can get one for $50.00. You plug it into your car, follow the instructions, write down the codes that appear, look them up in the including manual, and you know where to start. Even if you can't repair it yourself, give the mechanic the codes you found and they'll think twice before scamming you because you already know the possible problems.
My truck started running rough last year. Engine light came on. Checked the codes, googled a little, replaced the gas cap for $13.00 and the problem was solved. The gas cap wasn't air tight anymore and was letting air in and was screwing up the air to fuel mix and making it run rough. A mechanic could have told me almost anything and I would have just paid him to fix it.
https://www.amazon.com/ANCEL-AD310-Enhanced-Universal-Diagnostic/dp/B01G5EA74I/ref=sr_1_1?ie=UTF8&qid=1525374298&sr=8-1&keywords=code+reader
edit- added that they're cheap
ANCEL AD310 Classic Enhanced Universal OBD II Scanner Car Engine Fault Code Reader CAN Diagnostic Scan Tool - Black https://www.amazon.com/dp/B01G5EA74I/ref=cm_sw_r_cp_api_i_mAcQCbEX9TYAK
https://www.amazon.com/ANCEL-AD310-Enhanced-Universal-Diagnostic/dp/B01G5EA74I/ref=sr_1_5?crid=3J0UG99B3OY3T&keywords=obd+scan+tool&qid=1572484850&s=automotive&sprefix=obd+sc%2Cautomotive%2C222&sr=1-5
You can pull the check engine light codes yourself. Buy an OBD scanner like this. If it's gas cap related, you can reset the CEL yourself.
https://www.amazon.com/ANCEL-AD310-Enhanced-Universal-Diagnostic/dp/B01G5EA74I
There are a couple on amazon I'm thinking about. Would like to keep it under $50.
Deciding between this ANCEL AD310, and this ANCEL AD410. Either one seems to fit my pretty basic needs for a scanner...
here ya go: https://www.amazon.com/dp/B01G5EA74I/ref=cm_sw_r_cp_api_i_zm14BbNPB1NZP
[OBD II Engine Code Scanner] (https://www.amazon.com/dp/B01G5EA74I/ref=gbps_img_m-7_759e_1734342c?pf_rd_p=70acffa0-6735-44b1-b69d-ab83e4d3759e&pf_rd_s=merchandised-search-7&pf_rd_t=101&pf_rd_i=13887280011&pf_rd_m=ATVPDKIKX0DER&pf_rd_r=G2TTZ9G4FX9E7PDE2W37)
No, I plug in the code reader I have into the car and it tells me what the issue is right away so I know how urgent it is. That said, if your car's check engine light is on, there's almost always a reason for it and you shouldn't ignore it! :)
Here's one for $35~ plus tax. But theres a few cheaper available: https://www.amazon.com/dp/B01G5EA74I/ref=cm_sw_r_cp_apa_i_T8PUCbA5Z3GE1