Reddit reviews BYKES 10 Neodymium Super Strong Extremely Powerful Rare Earth Refrigerator Magnets 1/2 x 1/8 Inch Disc N48

We found 8 Reddit comments about BYKES 10 Neodymium Super Strong Extremely Powerful Rare Earth Refrigerator Magnets 1/2 x 1/8 Inch Disc N48. Here are the top ones, ranked by their Reddit score.

Grade: N48 - Extremely powerful magnetic materialPull Force per magnet is approximately 6.1 pounds under ideal conditions.Size: 1/2 inch diameter x 1/8 inch thick discsNickel (Ni) Plated (silver-like shine) - Axially magnetizedWARNING: VERY STRONG MAGNETS. KEEP OUT OF REACH OF ALL CHILDREN. THIS IS NOT A TOY. DO NOT INGEST OR INHALE. DO NOT PUT IN NOSE OR MOUTH. SWALLOWED MAGNETS CAN STICK TO INTESTINES CAUSING SERIOUS INJURY OR DEATH. SEEK IMMEDIATE MEDICAL ATTENTION IF MAGNET(S) ARE SWALLOWED OR INHALED. MAGNETS ARE BRITTLE. BROKEN MAGNETS ARE SHARP. MAGNETIC MEDIA AND ELECTRONIC EQUIPMENT HAZARD. KEEP AWAY FROM PACEMAKERS AND INTERNAL MEDICAL DEVICES. MAGNETIC MATERIAL IS REGULATED FOR AIR TRANSPORT.

Check price on Amazon

8 Reddit comments about BYKES 10 Neodymium Super Strong Extremely Powerful Rare Earth Refrigerator Magnets 1/2 x 1/8 Inch Disc N48:

u/fuckyou_space · 14 pointsr/DIY

I did something similar, but instead just stuck the magnets on the inside of the metal lid, which needs no glue.

Edit: BTW I chose these magnets.

u/Autsin · 4 pointsr/bicycling

If you stick some neodymium magnets to your bike (I put 2 on my left pedal) you'll be able to trigger the sensor! :)

Also has the advantage of allowing you to trigger a green light on the road where there are the embedded wires.

I use these: http://www.amazon.com/gp/product/B0084UASJQ/

Edit: Or maybe not... http://www.reddit.com/r/bicycling/comments/2hirgt/do_any_of_you_regularly_take_your_bike_places/ckt4py0

u/The-Shaw · 2 pointsr/Charcuterie

I actually made it. Cost me somewhere around $75 if I remember correctly. Buy all the materials listed below for the size/quantity you want, and then I custom printed and cut clear labels for the top and sides of the jar. The magnets are glued to the inside of the jar lids. If you get them strong enough they will never slide or slip. The ones I list can get about a half inch from the stainless base before they won't go back.

Stainless Steel Backplate - You can order in a lot of places - but make sure you have the correct steel makeup. Not all stainless is magnetic!

Superglue - Any standard superglue should work.

Magnets - It would seem that they don't sell these magnets anymore, but it should be easy to find something similar.

4oz Glass Hex Jars w/ Lids - This was the most reliable source at the time.

u/RVelts · 2 pointsr/geek

http://www.amazon.com/BYKES-Neodymium-Extremly-Powerful-Refrigerator/dp/B0084UASJQ/ref=pd_sim_indust_5

u/Rhidelsilpheed · 2 pointsr/costuming

I suggest getting these items Silver Sculpey Get one pack for each bullet splash you want to have.

Then get these. Make sure you have two magnets or each bullet splash.

Then I'd make one claw arm not two as it's a pain to go without two hands. To make the claw I'd grab some foam board.

Get some Super glue or hot glue.

Silver paint that matches the baked shade of the clay.

some blue paint that matches your cop uniform.

Start with the clay, open it and save the wrapper- shape the stuff into dishes with a entry hole or deep point. From the center of each dish make spirals that come out - You could even make the clay into a long snake and coil it around and around to make your dishes. Then make an indent to place one of your magnets flush into the base and make it 10% deeper and wider. Follow the instructions and bake it. Grab super glue and attach one magnet to the dish and the other threw your cop uniform.

The arm is gonna be a bit harder. You want to cut out some shapes from the foam core and then glue it with some superglue or hot glue. I'd start off with cutting two rectangles about as wide as your forearm and about 10 -12 inches longer . the remainder I would cut into long right triangles that are as long as the long piece. This should help make a box to fit your arm in, continue to cut and glue additional pieces to make your hooks. Paint the same color as your putty dishes and you should be done. To help with the details- blend your silver paint into your clothing by matching a blue of the uniform into the splashes and arm the transition into the silver.

u/brendanmc6 · 2 pointsr/Homebrewing

Based on my setup, you need;

Decent thermometer

Auto Siphon & tubing

hydrometer

wine/beer thief

carboy or bucket for fermenting + rubber stopper & blowoff tube

bottling bucket w/ spigot

bottling wand

bottle capper + bottles & caps

I recommend 10 gallon kettle, I regret getting only 8 gal.

mesh brew bag sized to fit your kettle. Useful for both BIAB and batch sparge brewing.

Optional but very useful;

10 gallon mash tun (square or round cooler + steel braid/false bottom + brass valve) I regret only getting a 5 gallon. Easy home depot built.

DIY stirplate using adjustable computer fan + magnets + stir bar and a flask (I pull it off with a 1 gallon glass jug)

vinator

Fermentation chamber with temp controller!

u/raider1v11 · 1 pointr/MechanicAdvice

wow. holy crap! clearly you have done this before on these cars.

so basically, you recommend putting an inline filter between the hard line and the carb, correct?
as far as the magnets, could i just put them on the underside of the tank? i could just line THESE MAGNETS up across the rear of the tank and that would be good right?
would you be able to tell me since i have the HEI on it, So on my timing since I have the hei in, should I be on stock timing and plugs, and plug gap? Or should I be on the spec for the 75 or 76? http://www.angelfire.com/extreme3/drchop/docscads.html - I would think same stock timing, but with the plugs and gap for the stronger spark right?

u/johnwayneblack · 1 pointr/Homebrewing

I already had them, but it was two of something like this.