Reddit reviews DataComm Electronics 50-3323-WH-KIT Flat Panel TV Cable Organizer Kit with Power Solution - White
We found 40 Reddit comments about DataComm Electronics 50-3323-WH-KIT Flat Panel TV Cable Organizer Kit with Power Solution - White. Here are the top ones, ranked by their Reddit score.
Low profile design fits behind the industry’s thinnest mounts and TVsGrounded recessed receptacle allows you to install power behind your wall mounted TV and other similar applicationsConceal multiple AV cables behind your wall mounted TVMounting wings are molded into the cable pass-through sides of the top plate to fasten against the drywall as you tightenCable pass-through ports on the top and bottom plates allow you to run your low voltage AV cables from your TV through the wall
Power cords carry higher voltage than A/V cords (like HDMI cables). I'm not an electrical engineer or general contractor, but they emit enough heat that it is considered a fire hazard to run them inside residential walls due to lack of air flow. Additionally, it is not up to building code to run such cords within walls.
Instead, you need to either have an electrician properly install wall outlets as needed, or use a type of kit that allows for the TV's power cord to plug into an 'outlet' on the wall, then the kit's to-code cabling runs down and allows you to connect to an existing wall outlet.
Something like this:
https://smile.amazon.com/Datacomm-50-3323-WH-KIT-Panel-Organizer-Solution/dp/B001PB7UVA/
As running power cords inside walls violates building code, if your house were to catch fire due to this it's possible your home owners insurance wouldn't pay out a dime.
I used one of these for the super clean look. Pretty easy. Datacomm 50-3323-WH-KIT Flat Panel TV Cable Organizer Kit with Power Solution - White https://www.amazon.com/dp/B001PB7UVA/ref=cm_sw_r_cp_apa_i_uj5wCbWKSASAD
I was under the impression that code for electrical wiring doesn't allow for tv power cables to be in the wall. You can actually purchase "power bridges" for this reason.
https://www.amazon.com/dp/B001PB7UVA/ref=cm_sw_r_cp_api_xyQHybSRV0P6H
I only mention this as it is possible for the tv power cord to catch fire in the wall. Although I haven't personally seen this happen, I dont know of any professional av installers that would run the power wire in the wall this way. They would either have an outlet installed or use a power bridge.
find a space between the studs that doesn't have a firebreak. cut a hole in the drywall behind the TV, cut another hole under the wall unit. fish wires through.
https://www.amazon.com/Datacomm-50-3338-WH-KIT-Mount-Cable-Organizer/dp/B003N7NJBY/
or
https://www.amazon.com/dp/B001PB7UVA/
It’s one of those outlet relocation and cable pass through things you can buy at a hardware store to run cables in the wall for a mounted TV. People who are afraid of adding an outlet will use this to safely/legally (within code) run power from the TV. You would connect an extension cord to the prongs on the wall and plug it into an outlet. AV cables pass through on the right.
Edit: like this product: Datacomm 50-3323-WH-KIT Flat Panel TV Cable Organizer Kit with Power Solution - White https://www.amazon.com/dp/B001PB7UVA/ref=cm_sw_r_cp_api_i_i0EACbK9RRKXQ
Honestly, I don’t understand why folks just don’t add an outlet up high above an existing one. It’s cheaper, cleaner, and just as easy to install as one of these things.
better yet, hide the cords in the wall with a kit https://www.amazon.com/dp/B001PB7UVA/
https://www.amazon.com/gp/product/B001PB7UVA/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1
please hide your tv wires!!
I used something like this.
It might not have enough outlets for OP, but he might be able to use something like this or this at the top part.
FYI: Low voltage not required to be in conduit in Chicago. A friend of mine is an electrician in Chicago. Rest of electrical needs conduit that is true.
I have run coax cable, Ethernet, speaker wire and phone lines in my house through walls without conduit. Just make sure the wire you use is riser rated if passing from floor to floor or In-wall rated if keeping on same floor. Plenum rated if running via heavy ducts/returns. I have generally used riser rated for all my in-wall applications.
Don’t run an electrical cord from a tv or extension cord in the wall. You always use something like this: Datacomm Electronics 50-3323-WH-KIT Flat Panel TV Cable Organizer Kit with Power Solution - White https://www.amazon.com/dp/B001PB7UVA/ref=cm_sw_r_cp_api_i_wGA7CbQG8K63V
You could also buy a longer cord, route the cord horizontally to the door frame and the down along it and then back over to the outlet. You could also buy a kit that would allow you to do the cable through the wall. Like this: https://www.amazon.com/dp/B001PB7UVA/ref=cm_sw_r_cp_apa_i_kdJ2CbBYR4D6W
> which included adding an extra outlet behind the tv for whatever reason.
Because you can't legally run a power cord/extension cord through a wall. Can only be romex power cord.
So if you want a "clean" install you have to basically add a new outlet behind the TV.
​
They make kits like these that does the same thing https://smile.amazon.com/dp/B001PB7UVA
Any kit like this works - pretty easy.
Came here to say this. Something like this is super easy and it's $50. I guess 80% of the budget went to the chair. :p
Came here to say that, cable channels are da bomb, next level up is these things if you are allowed. Easy to install, run the cables down behind the wall and out the other side, totally hidden. Really nice clean look
https://www.amazon.com/dp/B001PB7UVA/
https://www.amazon.com/dp/B075343YSZ/
Also, I totally lol'd at "speel"
This is what I use... keeps within code and all that too.
http://www.amazon.com/gp/product/B001PB7UVA/
I used this and it was a breeze.
http://www.amazon.com/gp/product/B001PB7UVA/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
We gotta do something about those cables. Check this out. Nice setup otherwise!
https://smile.amazon.com/Datacomm-50-3323-WH-KIT-Panel-Organizer-Solution/dp/B001PB7UVA/ref=sr_1_4?ie=UTF8&qid=1518206910&sr=8-4
If the cables were longer I would do this.
https://www.amazon.com/Datacomm-50-3323-WH-KIT-Panel-Organizer-Solution/dp/B001PB7UVA/ref=sr_1_8?ie=UTF8&qid=1522771598&sr=8-8&keywords=wall+cable
Another use posted this https://www.amazon.com/dp/B001PB7UVA/ref=cm_sw_r_cp_api_xyQHybSRV0P6H
I haven't looked to see if it is in accordance with the national electric code, but if it is, it would make the job a lot easier
Umm, actual professional AV Installer here.
https://www.amazon.com/gp/aw/d/B001PB7UVA/ref=mp_s_a_1_sc_3?ie=UTF8&qid=1511231243&sr
Here is one I found on Amazon that should do the trick.
Really cool looking setup. Just want to point out a few things.
I would highly recommend just getting something like this, https://www.amazon.com/DataComm-Electronics-50-6623-WH-KIT-Organizer-Solution/dp/B001PB7UVA It's not really that much extra effort. you run the wires like you already did, but you use a solid wire rated for in-wall inside the wall.
​
Exactly what might happen if you just use a normal extension cable in the wall. I'm not sure besides potential fire hazard (extension cables do heat up as you run current through it, normal it dissipates it just because it's lying around. Being insulated within the wall sounds like a potentially bad idea).
Amazing work man!
If you own your own place (or don't care about large holes in the wall) might I suggest one of these.
Really makes a huge difference in how clean something looks.
Yup, you cut a pair of holes in the wall. If you want to throw money at the problem, you can install something like this to get both power and a spot for cabling up there. Or if you're handy, you can install your own outlet and just get some brush plates for your HDMI etc.
If you are allowed to drill holes (I see the TV is mounted), you really should do something like this:
Datacomm Electronics 50-3323-WH-KIT Flat Panel TV Cable Organizer Kit with Power Solution - White https://www.amazon.com/dp/B001PB7UVA/ref=cm_sw_r_cp_api_i_rJ6mDb8BN2EDM
Something like this?
https://www.amazon.com/gp/product/B001PB7UVA/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1
There are a lot of variations of this thing out there.
I don't have experience installing - we almost went this route, then decided a large enough media console would look better and be more practical than an on- or in-wall solution. But, it's very well rated.
They have these kits on Amazon that work really well if you already have a dry wall saw and wire snake. First one took an hour but my upstairs TV only took 30 minutes.
It looks much cleaner if you use thiskit to run the cables.
I used this 2 years ago worked out great. http://www.amazon.com/gp/product/B001PB7UVA/ref=oh_aui_search_detailpage?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B001PB7UVA/ref=oh_aui_detailpage_o08_s01?ie=UTF8&psc=1
I'd second this, but maybe use that hole to your advantage by using it to hide low voltage cabling in the wall. get two birds stoned at once. I used this: hidey hole
Something like this can be used - https://www.amazon.com/Datacomm-50-3323-WH-KIT-Panel-Organizer-Solution/dp/B001PB7UVA/ref=sr_1_3?ie=UTF8&qid=1519927920&sr=8-3&keywords=tv+outlet+recessed+box
I'd find a way to conceal the wire and go wired anyways. Wireless is good for phones and that's about it. They make kits to create an in wall conduit to run cables along with power.
[See here](Datacomm 50-3323-WH-KIT Flat Panel TV Cable Organizer Kit with Power Solution - White https://www.amazon.com/dp/B001PB7UVA/ref=cm_sw_r_cp_apa_h4cQBb2KZ5705)
Here is the one I used.
https://www.amazon.com/dp/B001PB7UVA/ref=cm_sw_em_r_mt_dp_U_d0BDCbEZEYRZ0
For those who are handy and with products like these, it could be simple and without an electrician:
https://www.amazon.com/PowerBridge-Recessed-Management-PowerConnect-Wall-Mounted/dp/B00GWGZKF6
https://www.amazon.com/Datacomm-50-3323-WH-KIT-Panel-Organizer-Solution/dp/B001PB7UVA/ref=pd_day0_hl_23_1?_encoding=UTF8&pd_rd_i=B001PB7UVA&pd_rd_r=042b86e4-f3e2-11e8-acef-0dacba850be4&pd_rd_w=8CeM6&pd_rd_wg=6inpi&pf_rd_i=desktop-dp-sims&pf_rd_m=ATVPDKIKX0DER&pf_rd_p=ad07871c-e646-4161-82c7-5ed0d4c85b07&pf_rd_r=4G8V7RY52GNZJ6D0JTMB&pf_rd_s=desktop-dp-sims&pf_rd_t=40701&psc=1&refRID=4G8V7RY52GNZJ6D0JTMB
​
If you can't hide wires under the desk because it's glass, I would suggest hiding them behind walls (if you own the wall you'll be cutting a hole into) and using a tub for all the power bricks and surge protectors.
Wall mount TV power/data cable passthrough
Cable Management Box(es)
you need something like this.
https://www.amazon.com/Datacomm-50-3323-WH-KIT-Panel-Organizer-Solution/dp/B001PB7UVA/ref=sr_1_cc_1?s=aps&ie=UTF8&qid=1523348881&sr=1-1-catcorr&keywords=tv+mount+wiring+kit
One common option is something like this:
https://www.amazon.com/Datacomm-50-3323-WH-KIT-Panel-Organizer-Solution/dp/B001PB7UVA/
Power, ethernet, video, and any other low voltage wires are passed behind the TV into the wall, and then can come out at floor level behind furniture or similar.