Reddit Reddit reviews Dremel 7300-N/8 MiniMite 4.8-Volt Cordless Two-Speed Rotary Tool

We found 19 Reddit comments about Dremel 7300-N/8 MiniMite 4.8-Volt Cordless Two-Speed Rotary Tool. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Power Tools
Power Rotary Tools
Power & Hand Tools
Dremel 7300-N/8 MiniMite 4.8-Volt Cordless Two-Speed Rotary Tool
Cordless small rotary tool; compatible with Dremel bit accessories; 1/8-inch colletSmall rotary tool ideal for delicate tasks and finer work; 2 speeds (6,500 and 13,000 rpm)Lightweight plastic housingIncludes MiniMite 7300-N/8 4.8-volt cordless two-speed rotary tool, (8) accessories, wrench, battery, and charger8 inches long; 1.4 pounds; 2-year warranty
Check price on Amazon

19 Reddit comments about Dremel 7300-N/8 MiniMite 4.8-Volt Cordless Two-Speed Rotary Tool:

u/Doots_Nugent · 21 pointsr/aww

Try a dremel if you have not already. The pressure from those clippers can be irritating even if they don't touch the quick

u/ThelceMan · 7 pointsr/xcountryskiing

Hello,

Professional amateur rollerskier here:

Step 1. Pick up some rollerski specific carbide steel tips such as these


Step 2. Use them and keep those tips SHARP! So many people do not sharpen their tips before they go out to their detriment.

For sharpening I reccomend buying a dremel tool such as this and then using these tips

Step 3. Sharpen often! In my opinion, it is better to sharpen a little bit every time than a lot every once in a while.

I hope this has been helpful!

u/Saiiyk · 5 pointsr/aww

Dremel 7300-N/8 MiniMite 4.8-Volt Cordless Two-Speed Rotary Tool


Just use the brown one that’s for sanding and start on the lowest setting and move it around his feet only touching him the the end of it,the battery part, To get him used to the noise.
It should last you a good while since you’re only doing his feet. Good luck and I hope it helps :)

u/LileepLoves · 4 pointsr/DogCare

It could be that she doesn't like the sound the clippers make but what I've noticed while working is that most dogs don't like the pressure you put on the nail before you actually clip them because you're trying to avoid the quick.

I'm a groomer but before I even went to school for that I use to do everything for my dogs when it came to grooming, bathing and caring for their nails. When the time came to clip the nails I would slowly put pressure on the nail so I could clip it and avoid quicking them but it would freak them out because I was doing it that way.

I looked up videos of people using peanut butter to occupy them while you're cutting the nails and to take very little bits of nail off in one quick snap of the clippers and when they didn't react to it I would praise my dogs and let them know it was okay. Most of my dogs have black nails so I did it that way and now they're all comfortable with the nail clippers and the Dremel. I kept a routine on them and cut them every 2-3 weeks so not only will they get use to it I can keep the nails short. Now I just clip them and dremel off the sharp corners.

These are the nail clippers and dremel I have and that I personally love. http://www.amazon.com/gp/aw/d/B0002ARUKQ?pc_redir=1411784168&robot_redir=1

http://www.amazon.com/gp/aw/d/B003TU0XFU?pc_redir=1411972862&robot_redir=1

You can get the clippers at Petco, Petsmart or pet supermarket and the Dremel you can find in the automotive section of Walmart.

u/geekychick · 2 pointsr/AskWomen

This is the one I got: http://www.amazon.com/gp/product/B003TU0XFU

It was so inexpensive, I figured why not.

u/Japandance · 2 pointsr/StonerEngineering

http://www.amazon.com/Dremel-7300-N-MiniMite-4-8-Volt-Two-Speed/dp/B003TU0XFU/ref=sr_1_5?s=power-hand-tools&ie=UTF8&qid=1368719810&sr=1-5

This will technically get the job done, but, like I said, it might take significantly longer without the diamond bit.

u/chadcf · 2 pointsr/dogs

I just use a Dremel Mini Mite though you might need to step up to the next more powerful one for a big dog.

I don't use clippers at all. Too nervous about cutting the quick and generally my dogs have done better with a dremel. I mean they still don't like it but once they get used to it they don't try to get away as much. The only catch is to be careful to not dremel too much as it will get hot and can burn the quick. But on high speed I can take off 2-3 weeks worth of growth in a few seconds (depends on the dog and how hard/large their nails are). Plus it leaves things nice and rounded so it's not as rough on floors/skin.

u/SanicRealm · 2 pointsr/puppy101

ok, here you go:

  • Metal Comb
  • Pin Brush
  • Detangler
  • Clippers - I use these but Wahl is also really good
  • Different Blades - if you get the Andis Clipper
  • Metal comb attachments - get these and not the cheap plastic ones
  • Grooming Table - This is optional but if you have a wiggly pup like I do, they're helpful. If you get this you should also get these
  • Dremel for nails

    Now keep in mind that I plan on doing 95% of the grooming for the rest of my pups life. Since he's a standard poodle, a full groom would cost me anywhere from $75 to $120 (every 4 to 6 weeks) due to his size. So, for me, investing in all of the above will save me a lot of money in the long run.

    *Edit - If you go this route and get your own clippers - make sure you get some blade cleaner/oil, I use this
u/ninjabeerwench · 1 pointr/dogs

https://www.amazon.com/gp/aw/d/B003TU0XFU/ref=mp_s_a_1_1?ie=UTF8&qid=1485328266&sr=8-1&pi=AC_SX236_SY340_FMwebp_QL65&keywords=dremel+minimite&dpPl=1&dpID=41pjRg6Q9LL&ref=plSrch


If you cut a dog's nails instead of filling, you risk hitting the quick (which not only bleeds, but hurts like hell and makes the dog HATE having his nails done afterwards...) but also risks cracking and splitting of the nail.
I use a Dremel, and grind the nails down. Not only do the dogs hate it much less, but you get nice round tips instead of sharp edges. No chance of cutting too short, and no risk of cracking nails.
Even better, these tools are inexpensive, easy for beginners, and well made. I've been using the same one for years now! Sanding tips are super cheap and easy to replace, too.
Good luck!

u/chaffg · 1 pointr/Gunpla

Get yourself a small Dremel: http://www.amazon.com/Dremel-7300-N-MiniMite-4-8-Volt-Two-Speed/dp/B003TU0XFU/ref=sr_1_3?ie=UTF8&qid=1373437623&sr=8-3&keywords=cordless+dremel

Insert a thin dowel like a toothpick or cocktail stir into the Dremel head, then wrap some masking tape around the dowel such that the tacky side faces out.

Fit a bead snugly onto the tape. Now sand the nubs down by running the Dremel and holding the bead as it spins against some sand paper affixed to a firm surface (or use a sanding stick: http://www.amazon.com/Squadron-Products-Sanding-Stick-Coarse/dp/B000CDM4OU/ref=sr_1_2?ie=UTF8&qid=1373437785&sr=8-2&keywords=squadron+sanding+stick). Keep the sanding surface wet to carry away the dust.

You can use finer and finer grits to polish the beads to a shine.

I used this technique on my MG Marasai. This is a really quick way to sand those tiny things and it will make them buttery smooth. If you do this right, there will be no stress mark where the nub used to be.

u/Pandrom · 1 pointr/esp8266

Unfortunately I was hoping to use RGB LEDS, I can't believe I didn't specify that. Sorry about that, I edited it in. Would you be able to explain the common cathode vs common anode? I'll be looking it up but just to make sure I have the right idea for it.

 

I'll more than likely be using a relay at first, following tlucas's comment above just to get a bit of a better understanding but will be pushing to move over to a more complicated setup using transistors as they seem to be more efficient.

 

Ah yes I had picked out a multimeter but is there a type that you would suggest? I wouldn't be against learning how to make a board, i've looked at tutorials and it seems reasonably simple for just a basic board with no special features. I looked into the materials for a board, but the only thing I haven't figured out is the dremel. Should I go with a handheld one or would a standing one be better?

Edit: It seems like the standing one would be better, however people aren't too fond of that one I linked, I may end up going with a drill press

u/xelaDevi · 1 pointr/dogs

Here's what I have: A non-pet specific Dremel with two speeds.

Dremel 7300-N/8 MiniMite 4.8-Volt Cordless Two-Speed Rotary Tool https://www.amazon.com/dp/B003TU0XFU/ref=cm_sw_r_cp_api_c-pXBbYTSENXG

u/sumerkhan · 1 pointr/dogs

My co-worker has this one: http://www.amazon.com/dp/B003TU0XFU/
It works really well, but I'm not sure how long she's had it. I have the one from your link and my battery no longer holds a charge. Useless.