Reddit Reddit reviews Enclosed AC/DC Power Relay with Protection & De-Bounce. Screw Terminals. 120V Trigger Input.

We found 17 Reddit comments about Enclosed AC/DC Power Relay with Protection & De-Bounce. Screw Terminals. 120V Trigger Input.. Here are the top ones, ranked by their Reddit score.

Automotive
Replacement Parts
Switches & Relays
Automotive Replacement Electrical System Relays
Automotive Replacement Accessory Power Relays
Enclosed AC/DC Power Relay with Protection & De-Bounce. Screw Terminals. 120V Trigger Input.
Safe and easy to install. Controls any AC or DC device.Durable high current relay for long life and reliable switching.De-bounce circuit for safety. Dry contact relay output - connect to any voltage circuit.Thermal switch and circuit breaker add safety, limiting current to 15 Amps.Includes detachable power cord.
Check price on Amazon

17 Reddit comments about Enclosed AC/DC Power Relay with Protection & De-Bounce. Screw Terminals. 120V Trigger Input.:

u/jerobins · 4 pointsr/esp8266

This is the polar opposite of SMD, but I thought I'd share my solution...

While I love DIY, smoke detectors are important. I wanted to interface with my home system but without compromising the integrity of the system.

Get a 120v first alert.
First Alert SA521CN Wireless Interconnected Hardwired Photoelectric Smoke Alarm with Battery Backup https://www.amazon.com/dp/B000EVO9D4

Get the smart relay interconnect.
BRK RM4 Smart Relay for First Alert https://www.amazon.com/dp/B0039PF21U
This includes schematic for wiring to the detector and the color codes for NO/NC relay connection.

~~Get an optocoupler or isolation relay. Mains Voltage! The output of the RM4 is 120V.
Enclosed AC/DC Power Relay with Protection & De-Bounce. Screw Terminals. 120V Trigger Input. https://www.amazon.com/dp/B017743I7S
The RM4 output powers the relay. The screw terminals connect to the 8266.~~

Get a Esp8266; Flash tasmota firmware. Configure for switch and mqtt. Wire it up.
First Alert is now part of the matrix.

Quick update: Did not need the second relay/optocoupler. The BRK RM4 is an isolated relay. Their docs did not make that perfectly clear so I assumed worst case w/o testing it.

u/BillyLongstroke · 2 pointsr/amazonecho

It was really easy since there is a 110 outlet under my fireplace. I used the relay below to trigger the switch and a TP-link smart plug. It was simple to hook up.

https://www.amazon.com/gp/product/B017743I7S/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1

u/gtg465x2 · 2 pointsr/Hue

I have a gas fireplace that was controlled by a switch on the wall. The switch was a low voltage switch that essentially just connected two wires together to turn on the fireplace and disconnected them to turn off the fireplace. The electronics that control the fireplace are behind a panel underneath the fireplace, and there is a decent amount of room and a power strip in there. I believe most gas fireplaces controlled by a switch on the wall have a similar setup.

So what I did was plugged in a Lutron Lamp smart plug (https://www.amazon.com/Lutron-Wireless-Lighting-PD-3PCL-WH-Assistant/dp/B00KHSXB60/ref=mp_s_a_1_3?keywords=lutron+lamp+dimmer&qid=1564055576&s=gateway&sprefix=lutron+lamp+&sr=8-3) to the power strip below the fireplace, and then I plugged in this AC/DC relay to that (https://www.amazon.com/gp/aw/d/B017743I7S?psc=1&ref=ppx_pop_mob_b_asin_title). What the relay does is just make a connection between its terminals whenever the outlet it’s plugged into (the Lutron Lamp plug in this case) is turned on. I then spliced the wires going to the switch on the wall and connected them to the relay. Then, the last step was to pair a Lutron Pico remote / switch (https://www.amazon.com/gp/aw/d/B00KLAXOE8?psc=1&ref=ppx_pop_mob_b_asin_title) to the Lutron lamp plug, and then I replaced the switch on the wall with the Lutron Pico switch. Now I can turn the fireplace off and on from a switch on the wall still, but I can also control the fireplace from HomeKit, Google Home, Alexa, etc. I also set up some rules to automatically turn off the fireplace if it’s been on for 3 hours, and to notify me if it turns on and I’m not home. These are just in case we accidentally hit the button to turn it on while we’re in bed or away or whatever.

u/RichardBLine · 2 pointsr/HomeKit

As long as the circuit is closed, does it matter how it got closed? Meaning, you can use any I/O module to complete the circuit and then hook up a Homekit switch to trigger the I/O module to close the circuit.

For instance, if you used something like this and connect one end to your fireplace (and I'm just using this module as an example as I don't know if it is compatible with your fireplace): https://www.amazon.com/Enclosed-AC-Protection-Bounce-Terminals/dp/B017743I7S/
and the other end to a Homekit switch or outlet. That should work, should it not ?

u/antikotah · 1 pointr/googlehome

I'm using one of THESE along with a MonoPrice garage door Z-Wave tilt sensor, and an old Z wave outlet I had laying around. Together, I built a template cover device out of it. The tilt sensor is the feedback and the open/close commands are scripts. Each open/close script basically turns on the Z wave switch (and therefore powers the relay), then turns it off after 3 seconds. I added conditions inside each script as well. For open, it ensures someone is home and the alarm is not on, otherwise it won't work. There is also a 30 second delay, then a condition that the door is actually open or close and a notification if the proper position is not met.

I can try to post the config later on if you want it. Don't have access to it right now.

u/upnorth77 · 1 pointr/homeautomation

I have done this. Worked just fine. I used a standard Wemo outlet (picked up recently from Amazon for <$20) connected to one of these $9 relays. I then used a piece of solid 18/2 to connect the relay to the fireplace switch terminals. One of the great things about the setup is that the original switch still works in case of an outage.

I'm planning on trying the same setup for my garage doors.

u/DonkeyKwonGames · 1 pointr/askanelectrician

Just as an update and thanks for all the feedback.

I bought this: https://www.amazon.ca/gp/product/B017743I7S/ref=ppx_yo_dt_b_asin_image_o01_s00?ie=UTF8&psc=1

Hooked up the fireplace switch cables to the ON and the COMMON wire. Plugged it into the smart outlet and then to the wall. Works perfectly and it all fits under the fireplace with the rest of the controls.

u/noroom · 1 pointr/RASPBERRY_PI_PROJECTS

If your UPS can provide the signal (most can), you should definitely go for that.

Otherwise, I've used this successfully in the past: https://www.amazon.com/gp/product/B017743I7S/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1

Super easy, plug and play into the GPIO.

u/mitemouze · 1 pointr/3Dprinting

I'm still in the middle of adding a filament sensor to my OctoPrint setup so I may be missing something, but I think you should be able to use that plugin to achieve pausing a print when the power disappears. The 'Filament Sensor Reloaded' plugin just looks at a GPIO line that you select to determine if filament is present or missing and you can pause the print. If you connect the GPIO to a voltage from the same source as the printer, then you can detect the power removed from the printer and pause. A simple way to do that would be a USB power adapter with a voltage divider from 5V to 3.3V or you could use this power detector - https://www.amazon.com/Enclosed-AC-Protection-Bounce-Terminals/dp/B017743I7S/ref=sr_1_6?ie=UTF8&qid=1506368549&sr=8-6&keywords=iot+relay#Ask

For $9, I'd probably buy the power detector.

Like I said, I haven't experimented with OctoPrint pausing yet, but I would expect the same behavior as pressing the pause button.

u/Gqsmoothster · 1 pointr/HomeKit

I use a Koogeek switch with this relay plugged in:

Enclosed AC/DC Power Relay with Protection & De-Bounce. Screw Terminals. 120V Trigger Input. https://www.amazon.com/dp/B017743I7S/ref=cm_sw_r_cp_api_xVgRzbR56SQAV

The relay senses the 120v and closes the circuit of the two wires from your fireplace. In my case the fireplace had an external thermostat connected to it. I took out the two wires from the thermostat switch and connected those two wires to the relay. Now when the relay senses current it closes the circuit of the fireplace switch but without adding any electricity to it.

u/Sternberger · 1 pointr/HomeKit

What makes Nold interesting is the ability to control 2 doors as well as attach a magnetic sensor to let you know the open/close state. This is why I loved the WeMo Maker so much.

If you want an inexpensive garage door opener, use this with a WiFi outlet:

Enclosed AC/DC Power Relay with Protection & De-Bounce. Screw Terminals. 120V Trigge... https://www.amazon.com/dp/B017743I7S/ref=cm_sw_r_sms_c_api_Zi7KBb1KYGJB2

u/CamoHiddenDJ · 1 pointr/homeautomation

https://www.amazon.com/dp/B017743I7S/

This opens/closes a relay that you can wire into a contact sensor of some sort. Plug it into the clapper and you can do whatever automation you want with it. Normally use these on control4 systems, so not sure what zwave/zigbee/usb contact sensors are out there.

u/ob2kenobi · 1 pointr/homeautomation

You can connect it to an AC relay.

I use mine to open and close my garage door.

u/jodyw912 · 1 pointr/HomeKit

If you are up to doing a bit of wiring you can put together a rig that will work.
To do so you need to get a powered relay. There may be some on Amazon. https://www.amazon.com/Enclosed-AC-Protection-Bounce-Terminals/dp/B017743I7S/ Maybe something similar to this one but maybe one that already has a 220 plug on it.
Then use a iDevices or iHome plug to power it.
If not sure about wiring get an electrician to handle it.
Not quite a standard way of doing it but it would work.

u/dlflannery · 1 pointr/amazonecho

OK, here's an approach that should work and has worked for others:

Use a TP-Link HS100 Smart WiFi/Alexa-enabled plug driving an isolated relay, e.g.. https://amazon.com/Enclosed-AC-Protection-Bounce-Terminals/dp/B017743I7S/ref=sr_1_2?ie=UTF8&qid=1483241234&sr=8-2&keywords=120v+Relay+switch

Here is a quote from a reviewer who controlled a fireplace:

>Does exactly what it's supposed to. I used this with a TP-Link Smart Plug to allow me to use my Amazon Echo turn my gas fireplace on and off. The project took literally 5 minutes to hook up and works great. If I were going to pick any nit, I wish they had a version with a solid state relay so it doesn't "click" on and off, but that's really minor, and for this price, it can't be beat.Does exactly what it's supposed to. I used this with a TP-Link Smart Plug to allow me to use my Amazon Echo turn my gas fireplace on and off. The project took literally 5 minutes to hook up and works great. If I were going to pick any nit, I wish they had a version with a solid state relay so it doesn't "click" on and off, but that's really minor, and for this price, it can't be beat.

Setup the smart plug at an AC outlet close to the FP. Then plug the AC cord that comes with the relay module into the smart plug. The two wires that control the FP connect to the Gnd and NO contacts of the relay. Those two wires are very low voltage and current ("Millivolt circuit") that turn on the fire when connected. They should never contact a 120V circuit, which is why you need the isolated relay module.