Reddit reviews GreatestDeals (11x - 100x) NTAG215 NTAG 215 25mm NFC Stickers 100% Guaranteed to Work Perfectly with TagMo (Android) and Placiibo (iOS)! Multiple Sizes Available! (50 Stickers)
We found 6 Reddit comments about GreatestDeals (11x - 100x) NTAG215 NTAG 215 25mm NFC Stickers 100% Guaranteed to Work Perfectly with TagMo (Android) and Placiibo (iOS)! Multiple Sizes Available! (50 Stickers). Here are the top ones, ranked by their Reddit score.
Highest Rated and Quality NTAG215 NFC Tags on Amazon!! - 100% Guaranteed to work with TagMo and Amiibo Cards. NTAG215 NFC Sticker Pack ships blank ready to program!We stand by our product 100%! If for any reason your tag does not work, has an error, or becomes damaged, contact us immediately for a free replacement!USA Seller FREE Prime Shipping - Trusted Amazon Seller with 100s of satisfied customers!45+5 (50 Total) NTAG215 NTAG 215 NFC Stickers - 25mm Diameter - RFID - Paper Top - Strong Adhesive Bottom
50 x NTAG215 NTAG 215 NFC... https://www.amazon.com/dp/B071ZZTT6T
They are cheaper on Amazon.
https://www.amazon.com/NTAG215-NFC-Stickers-Guaranteed-Perfectly/dp/B071ZZTT6T/ref=mp_s_a_1_3?keywords=nfc+215+stickers&qid=1569471327&sprefix=nfc+215+sticker&sr=8-3
I’d like to thank this sub for all their ideas! I started my amiibo creation journey with a simple sticker attached to a rubber duck for Epona; when I saw my best man’s amazement when I showed him, I knew exactly what I needed to do for his best man gift.
I started by attempting to have a playing card company print some of the amazing card designs found on this sub. After being rejected for copyright because of the amiibo logo, I edited it out (as that’s where I was planning to place the sticker); they then told me the entire set was not going to be able to be made, which sent me into a minor panic. I switched up tactics and went to making coins.
Since there are so many varieties of coin sizes, I was a bit overwhelmed compared to the stock PVC or playing card sizes. After doing some research, I decided on the AIRTITE 30mm black ring coin holders. This was because the inner diameter is 1.55 inches, and I bought a 1.5-inch hole punch for the smallest amount of wiggle room.
I went for a cleaner look (just image of amiibo) which are downloadable from Nintendo’s amiibo lineup website. I wanted the black ring to be shown on the amiibo side but not the back, so I sized them all to fit within a 1.2-inch circle in word, centered within a 1.6-inch circle. I removed the inner guide circle and copied it into GIMP, a free open source program. This is my first time using it, but the best way I found was to paste each image in as a new layer, transform it to the proper size, and move it into place. (I'm sure there are better ways; this was all trial and error).
It is a destination beach wedding, so I found an appropriate Zelda image that wouldn’t look bad in a smaller size or where too much is cut off because of the circular design. The font is a free download, Hylia Serif. I messed up and sized the image to 1.5 inches, not 1.55 (hence the small gaps at the top and bottom). I printed them at home on glossy photo paper using an inkjet printer.
Assembly went bottom coin holder-back image-NFC tag-amiibo image-black foam ring-top coin holder. I added the black ring to center the 25mm sticker, then removed temporarily in order it to put the other image underneath the ring. While it is possible to reopen them, it is very tedious, and I strongly encourage double checking before closing (don’t forget a sticker like I did…). You can program them after you assemble them without any issues.
This is probably too much detail, but a lot of posts show amazing results and I knew I felt unsure of things many times before I ironed everything out. Hopefully this can make creating your own more accessible for future first timers! I’m going to work on cleaning up my coin pdfs but will post them soon! It’s a total of 36 coins (Zelda, Splatoon, and wedding Mario, naturally).
TL;DR:
Materials: AIRTITE 30mm black ring AIRTITE coin holders; 25mm NFC Stickers; 1.5 inch hole punch
Links:
https://www.gimp.org/
https://smile.amazon.com/NTAG215-NFC-Stickers-Guaranteed-Perfectly/dp/B071ZZTT6T/
https://smile.amazon.com/Black-Capsule-Air-Tite-Holders-Dollars/dp/B01EP1YREY/
https://smile.amazon.com/EK-Tools-Circle-1-50-Inch-Package/dp/B0090JVGFU/
https://www.nintendo.com/amiibo/line-up
http://artsyomni.com/hyliaserif
I used these and they're batting a thousand right now, as none have failed or had an error.
https://www.amazon.com/gp/aw/d/B071ZZTT6T?psc=1&ref=ppx_pop_mob_b_asin_title
50 x NTAG215 NTAG 215 NFC Stickers 100% Guaranteed to Work Perfectly with TagMo! (45 Pieces + 5 Bonus!) https://www.amazon.com/dp/B071ZZTT6T/ref=cm_sw_r_cp_apa_i_Ojz3DbHDMSSVB
Coin Capsules Round Plastic Coin Holder Case with Storage Organizer Box for Coin Collection Supplies (27 mm, 100 Pieces) https://www.amazon.com/dp/B07CNTTVF9/ref=cm_sw_r_cp_apa_i_Vlz3DbNKBS6RK
I also used Tagmo and NFC Bank.
No bad ones yet!
iPhone 11 pro. I got these tags
50 x NTAG215 NTAG 215 NFC Stickers 100% Guaranteed to Work Perfectly with TagMo! (45 Pieces + 5 Bonus!) https://www.amazon.com/dp/B071ZZTT6T/ref=cm_sw_r_cp_api_i_345XDb7F83780