Reddit reviews Irwin Tools Combination Square, Metal-Body, 12", 1794469
We found 10 Reddit comments about Irwin Tools Combination Square, Metal-Body, 12", 1794469. Here are the top ones, ranked by their Reddit score.
Black precision-etched scalesDurable cast zinc bodyRust proof stainless steel bladePerfect for 90° and 45° markingCan be used as a gauge for transferring measurements
If you go hand tools, you can start with Rennaissance Woodworker’s minimum tool list. You can go with a lot of vintage tools to save money, but for fun I priced out all new tools of good quality. Many tools were recommended here. I've added a workbench and some reference books and videos too.
MINIMUM TOOL LIST
$169 Jack Plane Woodriver
$125 Hand Saw backless saw ~26″ in length
$28, $30, $35 - 1/4, 3/8, and 1″ chisels Ashley Isles MK2
$79 Back Saw Veritas Crosscut Carcasse
$12 Coping Saw Olson
$18 Marking Gauge Beech Marking Guage
$12 Square IRWIN Combination
$149 Some kind of sharpening set up (stones, sandpaper, whatever) Norton Waterstone Woodworker Package
$592 Subtotal
NICE TO HAVE
$13 Honing guide Eclipse style
$13 Marking knife Veritas
$22 Mallet Thor
$15 Book to learn from Essential Woodworker Book
$63 Subtotal
WORKBENCH
$27 Workbench plans Naked Woodworker
$123 Materials for Naked Woodworker, costs from Mike Siemsen
$35 Holdfasts Gramercy
$185 Subtotal
GRAND TOTAL
$840
It is made of 3/16" black Elmers Foam Board.
The tools I used are:
Used this list for a couple posts, its about $200ish in all to get you started. This list uses chisels in lieu of say a router plane for dados and doesn't have an option for grooves but that's later down the road. I've got a big enthusiast list as well if you'd be interested.
> Crosscut/Ripsaw: Irwin Double Sided Pullsaw https://www.amazon.com/IRWIN-Tools-Double-Edge-9-5-Inch-213103/dp/B0001GLEZ8
> Joinery Saw - I think this is the one Japanese saw I own? works okay https://www.amazon.com/Z-saw-Dozuki-Z-Saw/dp/B001DSY7G6/ref=pd_sbs_469_3?_encoding=UTF8&pd_rd_i=B001DSY7G6&pd_rd_r=RBVEGF6TKKCZHVCH7WSH&pd_rd_w=16INj&pd_rd_wg=gFI50&psc=1&refRID=RBVEGF6TKKCZHVCH7WSH
> Chisels https://www.amazon.com/Narex-Republic-Woodworking-Chisels-863010/dp/B00GPC74ZQ/ref=sr_1_1?s=hi&ie=UTF8&qid=1499302108&sr=1-1&keywords=narex+chisels
> Marking Gauge https://www.amazon.com/Crown-135-Marking-Gauge-Beech/dp/B00EC9AOZQ/ref=pd_lpo_vtph_469_lp_t_4?_encoding=UTF8&psc=1&refRID=ZBYMV8TF850C6M5JDGDG
> Bevel Gauge https://www.amazon.com/dp/B06XC2NYKS?psc=1
> Mallet - I'd personally make one or buy a used one (of heavier wood, good grain and quality construction.) Amazon has some though. https://www.amazon.com/Narex-gram-Beech-Carving-Mallet/dp/B00L7BQL54/ref=sr_1_11?s=hi&ie=UTF8&qid=1499302341&sr=1-11&keywords=mallet
> Combination square -does the work of several sizes of squares for the price of one - https://www.amazon.com/IRWIN-Combination-Square-Metal-Body-1794469/dp/B005XUHIBG/ref=sr_1_2?s=hi&ie=UTF8&qid=1499302407&sr=1-2&keywords=square
> A No 4 or 5 sized plane - I buy old Stanley's/Bailey's because they're great, and usually cheap for bench planes - Flea Market/Antique stores/ebay -$20 ish --- Amazon also sells new (I give no guarantee on quality however) - https://www.amazon.com/Stanley-12-404-Adjustable-2-Inch-Cutter/dp/B000FK3WI2/ref=sr_1_1?s=hi&ie=UTF8&qid=1499302507&sr=1-1&keywords=stanley+plane
> "Workbench" - temporary thing to hold pieces while you make dovetails - https://www.amazon.com/WM125-Workmate-350-Pound-Capacity-Portable/dp/B000077CQ0/ref=pd_cart_vw_2_1?_encoding=UTF8&psc=1&refRID=CA9X21QD5D7QAXKMGE6S
> Woodscrew clamp, used to clamp peice to workbench while chiseling waste - https://www.amazon.com/ATE-Pro-USA-30143-Handscrew/dp/B0006A4A5U/ref=sr_1_1?ie=UTF8&qid=1499303583&sr=8-1&keywords=wood+screw+clamp
>
> Other than clamps, glue, mortice gauge, etc, this is good enough to get you started making carcass (dovetailed) pieces of furniture, like a shoe cubby or bookshelf. (Currently making a chimney bookshelf for myself)
>
> Thats around $200 for getting you started. Add a mortise chisel and mortise gauge and you can start mortise and tenon work. Invest in pipe clamps when you reach a glue up point.
This makes me think that your x-gantry is not squared up properly, or when you were trying to get it square you forced those wheels out of alignment.
Disassemble the gantry from both carriers (you'll have to remove it completely from the z-screw to remove the left side) and adjust the wheels on the carriers first. They should be just tight enough to hold them up vertically but you should be able to slide them up and down with minimal resistance.
Then start the reassembly process. Install the left end of the gantry first, and get the gantry arm as flat/parallel as possible along the base's protrusion towards center. I lay something thick and flat on this protrusion so I can make sure the gantry arm is parallel to it. Slide that end on through the z-screw, etc.
Now when assembling the right side, you have your bolts visible on either side of the vertical track, so you can adjust for level/square from the right side. Do the same method as the left side with aligning the gantry arm with the protrusion that goes to center to get you close to square. Don't completely tighten these right side bolts, though. Measure DOWN from the top of the vertical struts to the gantry arm and tighten the right side bolts completely once you get it squared up. I recommend using a locking combination square, and don't worry about the exact number for distance, just that they are the same.
Through this whole process you shouldn't have touched your eccentric nuts and your base on the right should still be relatively stable.
it looks like this https://www.amazon.com/IRWIN-Combination-Square-Metal-Body-1794469/dp/B005XUHIBG/ref=sr_1_1?ie=UTF8&qid=1481037968&sr=8-1&keywords=compound+square
but I think it was my grandfathers prob 30+ years old so I assume its good. I can look into getting a digital one though.
What are you going to use the #4 plane for? Planing without a solid workbench and vise/hold downs is a chore. Perhaps a block plane or even sandpaper would be enough to get you started?
Square - get the Irwin combo, it's accurate enough for casual use. https://www.amazon.com/IRWIN-Combination-Square-Metal-Body-1794469/dp/B005XUHIBG
That stone is too coarse for woodworking tools. Either use sandpaper like others have suggested, or get the King 1000/6000 https://www.amazon.com/King-Sided-Sharpening-Stone-Base/dp/B001DT1X9O
I would argue that the chisels, while crappy, will make good sharpening practice. Or get the $5 Harbor Freight ones and sharpen them every 5 minutes - at least you'll become a sharpening expert fast.
I measured/marked the holes using a combination square. Then I drilled 5/8 holes in opposite corners cut area. Then I used a cheap ($20) electric jig saw to cut out the area as best as possible. I would follow the lines on one side, then flip it over and cut it again. The jig saw blade bends so it cuts on an angle. Finally, I used a chisel to remove excess material and clean up the holes and straighten them out.
Combination Square
https://www.amazon.com/gp/product/B005XUHIBG/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
1" Chisel (or you can get a set of three for a little more)
https://www.amazon.com/IRWIN-M444-1-Inch-MARPLES-Chisel/dp/B0000CBJH8/ref=sr_1_20?ie=UTF8&qid=1493124918&sr=8-20&keywords=irwin+chisel+marples
Mallet
https://www.amazon.com/gp/product/B00020JNDI/ref=oh_aui_detailpage_o09_s00?ie=UTF8&psc=1
Jig Saw
https://www.amazon.com/Black-Decker-BDEJS300C-Jig-4-5-Amp/dp/B00OJ72L84/ref=sr_1_1?ie=UTF8&qid=1493125013&sr=8-1&keywords=4.5+amp+jigsaw
This is what I have been using and it is great - perfect 90 degree corners and straight lines
https://www.amazon.com/dp/B005XUHIBG/ref=cm_sw_r_cp_api_Q0YfzbMQW2PYX
What kind of experience are you guys coming into this with?
Do you have mentors/are you yourselves familiar with the use and safety precautions necessary around power tools?
What kind of space are you in? Do you have a dedicated space to use or do you need to move things in and out of an area every meeting?
How much do you want to learn? Are you planning on using primarily Matrix/Tetrix this season or do you want to do custom fabrication?
If you're planning on using chain, I'd recommend getting at least one of these (Dark Soul #25 chain tool). You won't need to use master links again, and they're just in general great to have around.
I would definitely recommend getting Anderson Powerpole tools and items. Definitely get a TriCrimp and associated wire, connectors, and contacts, if you don't have them already.
I'd also recommend a few tools that come in useful just in general when it comes to FTC-- a good adjustable wrench is good to have around, whether you're doing custom or not. A ratcheting screwdriver is also good to have around, in addition to more standard versions. I'd also recommend my personal favorite allen wrenches (you can get just metric or standard sets, but I linked the paired version). For taking care of stuck bolts or anything else stuck, a good pair of locking pliers are also great. Also getting some good pliers for all your electrical needs is a good idea. Also extremely useful is a good square. On a similar note, a level is good for checking whether you actually bolted that part on straight.
You should also get a general set of combo wrenches and some of the specific sizes most common for FTC. Pretty much any reputable brand is fine for this-- don't spend more than about $50 for a set and $10 for an individual wrench (honestly, that would be super high, you should probably target half of that). A decent ratchet set is also good, but not absolutely essential.
Other good things to have around are a heat gun or heat bar (for doing custom plastic parts for your robot). You can do some great stuff with some creativity and some sheet polycarbonate.
To go with that, a vinyl cutter is great for doing sponsor decals and general cool stuff.
As far as "essentials" go, that depends on where you want to go. If you want to do lots of custom work-- or use something like 80/20, then you'll want some other tools to do that work. A good power drill is absolutely essential, and if you have the space, I'd definitely recommend getting a solid miter saw and an aluminum cutting blade (I know some people consider them too dangerous, but with proper safety training and precautions, I've never had a student or mentor get injured with one).
As far as materials for doing custom work go, I'd recommend getting some box aluminum (1x1 and 1x2) tubing, 1/8" and 1/16" polycarbonate (I'm partial to the dark tinted stuff, but it's a bit more expensive), and a full assortment of #6 and maybe #8 hardware. You'll also want some M3 screws for face mounting AndyMark and REV robotics motors. I like to use Copper State for this, because while they have a totally garbage web ordering system, their prices are great, and their website isn't that bad (to be honest, I'm a bit spoiled by McMaster-Carr).
You probably don't need me to tell you what kind of COTS parts might be good (if that's within the scope of this money). Electronics, good phones (not those stupid ZTEs), motors, are all good.
You'll notice that I'm not suggesting the very budget stuff-- while you can go that direction if you need to, quality tools help you get quality results. If you have the money to get and use the right tools for the job, I always recommend doing that as opposed to cheaping out with something you'll just end up breaking and messing up your robot with later.
A decent chunk of the tools I linked are suggested by my personal favorite review site, The WireCutter/SweetHome. I've used the majority of them, and my experience has been good enough that I don't have an issue recommending their suggestions for other tools relevant to FTC.
Hopefully that was somewhat helpful. I'd definitely consider the answers to the questions at the top-- they can help you narrow down what will actually be useful for you. I can definitely give more specific suggestions if you know what direction you're taking with robot building techniques and how much space you have/ whether you have to move.
I will say that he's going to be limited with that workspace, but he can get by with some basic stuff. I also have extremely limited space. I have an outdoor shop space, but since it's not insulated and has no power, I'm very limited in what I can do.
However, here's a good list of things to get.
Keep in mind that father's day is coming up soon, and tools like these are popular things to be put on sale. Keep your eyes open :)