Reddit reviews Klein Tools D275-5 Lightweight Flush Cutter, Up to 16 AWG, Grips Designed for Tool Control and Heat Treated For Durability

Not necessary, just cut it flush.
https://www.amazon.com/Cutter-Lightweight-Klein-Tools-D275-5/dp/B000GTMZHG/ref=sr_1_4?keywords=flush+cut&qid=1573177684&s=hi&sr=1-4

Got a soldering iron for Christmas and dove right in. This is my third 60% build, and by far my favorite.

Parts

• Clear acrylic case and Gat greens from Sentraq
  
• PCB from TechKeys
  
• Black aluminum plate and Cherry stabs from Originative
  
• DSA keycaps (PBT) from PMK
  
• LEDs from switchTop
  
• E-Projects 200 Ohm Resistors from Amazon
  
  

  Tools
  

• Solder sucker
  
• Heat Resistant Soldering Mat
  
• Hakko FX888D Soldering Station
  
• Kester 44 Rosin Core Solder 63/37 .031"
  
• Klein Tools Lightweight Flush Cutter
  
  I'm still tweaking my QMK keymap, but will contribute it to the repo once I get it to a good spot.
  

By flush cut, I mean these. https://www.amazon.com/Cutter-Lightweight-Klein-Tools-D275-5/dp/B000GTMZHG/ref=sr_1_6?keywords=flush+cut&qid=1574342422&sr=8-6

Saws are often called "pull saws", which shouldn't be too necessary with filament supports since they should break away with force. But I've got one for helping with lots of resin supports at once, but I don't like that one and should get a smaller and stiffer saw that doesn't bend.

flush cutters.

A lot of people love those auto tensioner/Clippers, but I've found that if you don't have them set perfectly on the the it will still leave more of a tail than if you just use these: http://www.amazon.com/gp/aw/d/B000GTMZHG?pc_redir=1396457586&robot_redir=1

I've built and/or rebuilt at least a couple dozen systems and never nicked a wire while cutting a tie. Then again, I'm not some troglodyte that takes a knife to zip ties. I use these.

Second this. I am the data center grunt.

I brought my own pair last week of these, because I can’t live without them.

They’re perfect. If you watch a Panduit termination video on YouTube: there is a reason he has these. Even more so for the 6a shielded stuff.

Edited for formatting.

Kanthal is typically used and will be your most commonly seen wire. I only know of Gplat as an alternative (I used it... not worth the price increase IMO) I get mine from Amazon, I originally started with 28 gauge, then a buddy let me borrow his 26 gauge, that was good too. I purchased some 24 gauge and it drains my batteries hard (which is why I want a dual box mod.)

Yes, a mod is the housing. Then you will need your atomizer and battery.

I started dripping with the IGO-w atty with the Smok Magneto Mod. Biggest problem I had with it is it was small and i had to drill the air holes. I still use the Magneto.

I would never suggest tank anything. I tried both the genuine and the clone russian 91% and it was a terrible experience.

So, for a beginner getting into dripping I would suggest these parts:

[Plum Veil Atomizer] (http://www.eciggity.com/plume-veil-clone-by-tobeco/) (Note! I have not bought anything from this site.)

ANY single battery 18650 mechanical mod. They all realistically do the same thing. RipTrippers.com does a lot of reviews, they should be able to point you in the right direction. I do however suggest one with a magnetic fire button instead of spring. (It will lower resistance and last longer because springs are weaker than magnets)

Atleast 2 [18650 Sony batteries] (http://www.myvaporstore.com/SONY_VTC5_18650_2600mAh_Battery_Flat_Top_30A_p/sny65026-f.htm)

Charger I chose the two battery one for money purposes but I suggest the 4 since it's only like $5 more and can charge a myriad of batteries

[These clamp things] (http://www.amazon.com/5-5-KELLY-Hemostat-FORCEPS-Straight/dp/B000QWK174/ref=sr_1_6?ie=UTF8&qid=1414788271&sr=8-6&keywords=medical+clamps) makes building much easier

I use these but a lot of people use nailclippers

[Wire] (http://www.amazon.com/Genuine-Lightning-Vapes-Kanthal-Resistance/dp/B00JVXVKB0/ref=sr_1_2?ie=UTF8&qid=1414788396&sr=8-2&keywords=28+gauge+kanthal+wire) either 28 or 26 gauge is what I would recommend.


Cotton Balls

[Ohm Tester] (http://www.amazon.com/gp/product/B00MBNCOMG/ref=s9_simh_gw_p328_d0_i1?pf_rd_m=ATVPDKIKX0DER&pf_rd_s=center-2&pf_rd_r=0J7AHRP45YSC4DHAS7DB&pf_rd_t=101&pf_rd_p=1688200382&pf_rd_i=507846)

Drill bits, allen keys or screwdriver to wrap coils around (i usually use Allen Keys)

Another Screwdriver for you builds

Tweezers are nice for accurate adjustments

Some people suggest a torch.... it's a waste of money for most builds. The main idea behind them is they are used to burn off any chemicals on the wire... but when you are done building you just fire it a few times before you put cotton in them and it does the same thing. Some builds need a more flexible wire... that is the only time you will need it.

Note: I 100% support the use of Clones, especially when you are starting out your vape life. They save so much money and do an adequate (if not better) job of most authentics.

Neat but not always usable in a tight space. All you really need is a small pair of flush cut side cutters. Every mechanic has them just for this purpose.

Klein Tools D275-5 5-Inch Lightweight Flush Cutter https://www.amazon.com/dp/B000GTMZHG/ref=cm_sw_r_cp_apa_XiZZzb9P1HDM4