Reddit reviews Legrand-Wiremold CMK70 Flat Screen TV Cord and Cable Power Kit
We found 13 Reddit comments about Legrand-Wiremold CMK70 Flat Screen TV Cord and Cable Power Kit. Here are the top ones, ranked by their Reddit score.
POWER OUTLET IN-WALL CABLE MANAGEMENT SYSTEM: The CMK70 Flat Screen TV Cord and Cable Power Kit is perfect solution for power outlet and in-wall cable organizer. It is suitable for all types of wall mount Flat Screen LED, LCD, and Plasma Televisions.BIG MONEY SAVING PACK: The Wiremold cable management kit includes 2 power grommets, pre-wired wire harness, hole saw/handle, fish tape and 6 ft. extension cord (to go from bottom grommet to existing power outlet)TO RATED WALL GROMMET KIT: Wiremold CMK70 Flat Screen TV Cord and Cable Power Kit is ETL Listed. It is top rated product with easy DIY InstallationHDMI CABLE PASS THROUGH: Wall Grommet Kit is the easy solution to running flat screen TV cables behind walls. It is a Brush style AV/ HDMI cable pass-through. The wires can be routed behind the wall for a clean look and its suitable for low voltage cables.IN-WALL POWER OUTLET: Wiremold CMK70 Flat Screen TV Cord and Cable Power Kit has two Power outlets. Works with most TV plugs (Max plug width 1.125 in.).
Hole in the wall and drop the cable down. Then put a wall grommet near your outlet.
Or one of the cable hiding plastic pieces, legrand makes a good one but make sure you use vinegar to remove them or else they’ll pull the paper off the drywall which Is a pain to fix.
Legrand
Wall grommet
Edit: forgot to mention that if you’re putting a power cable in the wall you’ll need a different cable to actually run through the wall to keep it in code as it is a potential fire hazard. Here is a good kit that would fit for this example
I'm a home theater installer myself (not a licensed electrician, just a DIY electrician) but yeah that violates NFPA/NEC
Correct way of doing things would have been using something like this or hire an electrician to have them place an outlet behind the tv.
The guy you got was a hack for sure alright
They sell kits that let you do it yourself.
"Simple installation: Do-it-yourself kit allows for neat and easy installation in under 30 minutes with no electrician or hard wiring involved."
I got this thing
Cut two holes in the drywall. One behind the TV, the other in a hideable place near an outlet. Everything runs in the wall. I can add or remove wires any time I want. Literally nothing to see.
You can get one of these bad boys
Legrand - Wiremold CMK70 Flat Screen TV Cord and Cable Power Kit, Recessed In-Wall Cable Management System with PowerConnect, White. https://www.amazon.com/dp/B006K3CM4S/ref=cm_sw_r_cp_api_kq1IBb3Y8ZCRB
Very nice work, it looks great.
The only criticism I have is that it is against code to run the power cable through the wall like that. There are many kits that can easily fix this, though they are kind of pricey
http://www.amazon.com/Wiremold-Company-CMK70-Screen-Cable/dp/B006K3CM4S/ref=sr_1_13?s=hi&ie=UTF8&qid=1372172782&sr=1-13&keywords=wiremold
Mount TV and place center below at ear level.
Also, you can conceal all of your cables and run power to the TV using something like this. They're pretty easy to install and look way nicer than using tape.
I cut a few holes in the walls to run the cables and power.
https://www.amazon.com/gp/product/B006K3CM4S/ref=ppx_yo_dt_b_asin_title_o08_s00?ie=UTF8&psc=1
Run this on the back of the "desk"
https://www.amazon.com/gp/product/B07B7JF74H/ref=ppx_yo_dt_b_asin_title_o05_s02?ie=UTF8&psc=1
And because I couldn't run cable from left to right behind the wall because of studs I use this to at least control the wires on the wall.
https://www.amazon.com/gp/product/B01JKO8724/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&psc=1
I put a hole in the wall behind the TV and installed this
Install something like this https://www.amazon.com/Legrand-Wiremold-Wall-Management-PowerConnect/dp/B006K3CM4S/ref=mp_s_a_1_7?keywords=in+wall+cable+management+kit&qid=1573651157&sprefix=in+wall+&sr=8-7 .. I've put that in a few places and it's pretty straight forward and includes everything you need except a drill.
Here's a better kit you can show him and explain to him what it is and how it works.
https://www.amazon.com/dp/B006K3CM4S/ref=cm_sw_r_cp_apa_i_uinPCb978NC1B
​
As you can see here, https://i.imgur.com/UvMSba9.png there are two "ends" of the in-wall kit, the male receptacle and the female receptacle.
The "cable" that runs between each of the receptacles can't be anything but romex because its within the wall.
However this kit, isn't pushing anymore over 15amp as its just a power cord for a single device, you're not running multiple devices off of the run, just the projector is running off of the run.
Just because the outlet that the kit plugs into is a 20amp circuit / outlet, doesn't mean the whole kit also has to be 20amp.
https://www.amazon.com/dp/B006K3CM4S/ref=cm_sw_r_cp_awdb_t1_kpNzDbMBP9B4V
Use this for hiding the cables. But you’ll need to take the TV down
Looks good but if you’re not renting I would spend the $40 and completely hide the cables in the wall. Using a kit like this one makes it look that much cleaner.