Reddit reviews Mediabridge Ultra Series Digital Audio Coaxial Cable (4 Feet) - Dual Shielded with RCA to RCA Gold-Plated Connectors - Black - (Part# CJ04-6BR-G2)

Use digital cables for best signal

I found the operation manual for it, I will update this post with the cables as I find them.

EDIT: iPod connector - https://www.amazon.com/Pioneer-CDI200-Direct-Cable-Headunits/dp/B000LYAZ4G

EDIT: Antenna - https://www.amazon.com/Mediabridge-Coaxial-Cable-F-Male-Connectors/dp/B003FVJYF8/ref=sr_1_5?s=electronics&ie=UTF8&qid=1491765159&sr=1-5&keywords=antenna+cable if you need it, otherwise your car should have the antenna cable already.

EDIT: DIGITAL OUT, which is Dolby Digital Audio Output - https://www.amazon.com/Mediabridge-ULTRA-Digital-Audio-Coaxial/dp/B00FMZX5RI/ref=sr_1_4?s=electronics&ie=UTF8&qid=1491765375&sr=1-4&keywords=dolby%2Bdigital%2Bcable&th=1

EDIT: IP-BUS, or Aux Input - https://www.amazon.com/Pioneer-IP-BUS-3-5-Input-Cable/dp/B002ZYVNH8

EDIT: I couldn't find the EXT cable, but here is the manual if you want to find it yourself. The diagram is on page 7. https://www.pioneerelectronics.com/pio/pe/images/portal/cit_11221/417372568AVICD3InstallationManual0221.pdf

EDIT: I wasn't able to find any wired remotes or cables for the Pioneer Avic D3.

Assuming the wireless transmitter connects with 3.5mm or RCA, you're going to need to use the SPDIF out with a coaxial audio cable and run that into a DAC like a Fiio D3 and then into the transmitter. The other connections (besides the headphone jack) are all inputs

>thanks.. i already got this

>it doesn't insert completely, but i get the bass signal out of it.. but its so subtle even at highest volume..

Yep, I've had those on my sub's as well. They go on like a vise so I'm not surprised you're having issues getting them to seat fully. I finally replaced mine as they were just too tight for my liking. I almost pulled my AV receiver off of it's rack removing one side. Be very careful removing these. You have to be forceful yet restrained if that makes any sense. My guess is they aren't seated fully and you'll need to push them in completely. Either that or get my Knu Konceptz cables or the Kable Direkt's I linked you😉.

thanks.. i already got this

it doesn't insert completely, but i get the bass signal out of it.. but its so subtle even at highest volume..

For the sub you'll just need 1 coaxial RCA cable out from the receiver (Like what I linked below for the Fiio).

One coaxial cable for the DAC into the receiver, Like this cable

and two RCA to 1/4 TRS cable for the receiver to the JBLs, Like this cable

If you already have the JBLs hooked up via the Fiio you should already have those last two cables.

The TV's COAX out looks like a yellow/orange RCA out, right?

You need a DAC to convert the signal from digital to analog.

This should do it.

You'll need a digital coax cable too

Xbox > (HDMI) > TV > (Coaxial) > Receiver

All you need is something like this https://www.amazon.com/Mediabridge-ULTRA-Digital-Audio-Coaxial/dp/B00FMZX5RI/ref=sr_1_1?s=electronics&ie=UTF8&qid=1466713959&sr=1-1

EDIT: All the suggestions here would work btw. Figure out which one works best for you.

Do you think this would work:

toslink --> https://www.amazon.com/RadioShack-Toslink-Digital-Converter-1500059/dp/B007Z83FN4/ref=sr_1_5?ie=UTF8&qid=1510604030&sr=8-5&keywords=toslink+to+coax

--> https://www.amazon.com/Mediabridge-ULTRA-Digital-Audio-Coaxial/dp/B00FMZX5RI/ref=sr_1_3?ie=UTF8&qid=1510604839&sr=8-3&keywords=digital+coax+cable

--> https://www.amazon.com/Monoprice-BNC-Male-Female-Adaptor/dp/B006VK8IEI/ref=sr_1_5?ie=UTF8&qid=1510604846&sr=8-5&keywords=rca+to+bnc