Reddit Reddit reviews MG Chemicals 99.9% Isopropyl Alcohol Electronics Cleaner, 945 mL Liquid Bottle

We found 34 Reddit comments about MG Chemicals 99.9% Isopropyl Alcohol Electronics Cleaner, 945 mL Liquid Bottle. Here are the top ones, ranked by their Reddit score.

Industrial & Scientific
Lab & Scientific Products
Lab Chemicals
Chemical Solvents
MG Chemicals 99.9% Isopropyl Alcohol Electronics Cleaner, 945 mL Liquid Bottle
99.9% Anhydrous solvent—Removes water and humidity from components leaving them dryMeets reagent ACSMeets MIL Spec TT-I-735A and ASTM D770Less than 0.001 g/100 mL non-volatile residuesSuitable for use in food facilities as a non-food chemical. NSF International registration #144029Low toxicitySafe for aqueous environmentsExcellent “Green Solvent” scores
Check price on Amazon

34 Reddit comments about MG Chemicals 99.9% Isopropyl Alcohol Electronics Cleaner, 945 mL Liquid Bottle:

u/Nexdeus · 38 pointsr/watercooling

Get mechanical grade alcohol, 99%, get it in the pressurized spray can, and regular bottle. Disassemble the GPU and get any parts that got coolant on them out of the system.

Get a clean plastic container that can fit the parts you've gotten wet. Put the alcohol in there from the non pressurized n bottle. Place parts in bath of alcohol, use the pressurized alcohol and qtips to clean your parts. Once done, let dry for at least 48 hours in front of a fan.

I've recovered an entire x99 system this way. Good luck.

Edit

https://www.amazon.com/MG-Chemicals-Isopropyl-Alcohol-Cleaner/dp/B005DNQX3C/

Spray

https://www.amazon.com/dp/B005T8PL1Q

u/Spire · 25 pointsr/buildapc

Ninety-one percent may be a lot better than 70%, but I wouldn't call it ideal.

FWIW, I have a bottle of this 99.953%-pure anhydrous isopropyl alcohol, which is even better.

u/anosmiasucks · 8 pointsr/vinyl

> Rubbing alcohol (99% if you can get it)

I'll just leave this here

u/Butthole_Scientist · 6 pointsr/pcmasterrace

It's pretty easy to clean this.


ESD circuit board brushes: http://www.amazon.com/Plastic-Handle-Circuit-Static-Brushes/dp/B00BM38YPW


99.95% Alcohol: http://www.amazon.com/MG-Chemicals-Isopropyl-Alcohol-Cleaner/dp/B005DNQX3C/

Distilled Water can be used as well, just give it a few days to dry out.

Dip the brushes in the alcohol, don't just add the alcohol to the board, you'll end up using too much.

Make sure to wait an hour or so to guarantee that its all evaporated.

u/ssjhayes · 6 pointsr/steroids

Using Amazon and Medlabsupply for ease (two stop shop). I havent found much better prices (maybe a few cents..) in my homebrew career. My setup is a bit more expensive than whats listed lol.

Equipment

u/c0nsumer · 3 pointsr/bikewrench

I think that percentage is far more important, as a result I buy 99.9% isopropyl. Other things, such as rubbing alcohol (70%) or even 90% stuff... That other 10% seems to be water and a small amount of oils.

I once tested this by pouring some in a CLEAN glass and seeing what residue is left after it evaporates. That remaining gunk is not stuff I want left behind, especially on brake parts, so I use the purest stuff I can easily buy.

Specifically, this: https://smile.amazon.com/gp/product/B005DNQX3C/

u/Anatolysdream · 3 pointsr/fragrance

Going to have to fry those headphones. High concentration isopropyl alcohol

u/CanardConfit · 3 pointsr/trees
u/edwardmagichands · 3 pointsr/trees
u/robotsokk · 2 pointsr/MechanicalKeyboards

Not sure what solder you used, but that looks like flux. Isopropyl alcohol (like this) should work fine as a cleaner.

u/schmak01 · 2 pointsr/techsupport

You can get it easy on Amazon, there are hundreds of brands to chose from.

This is what I use, since it contains no water and is 99.9%. use gloves though, it will dry the crap out of skin.

https://www.amazon.com/MG-Chemicals-Isopropyl-Alcohol-Cleaner/dp/B005DNQX3C/ref=sr_1_9?ie=UTF8&qid=1504808917&sr=8-9&keywords=99+isopropyl+alcohol

u/rwreef · 2 pointsr/Aquariums

Use isopropyl alcohol to clean the whole the inside. It's safe for Electronics and will make it look like new. I would use a krylon paint on the rusty screws after removing the rust.

MG Chemicals 824-1L 99.9% Isopropyl Alcohol Liquid Cleaner, Clear , 945 mL (1 US Quart) https://www.amazon.com/dp/B005DNQX3C/ref=cm_sw_r_cp_apa_i_xyE1DbQ5BGQWF

u/nonja121 · 2 pointsr/Throwers

I use 99.9% isopropyl alcohol (electronics cleaner). Works great,

MG Chemicals 824-1L 99.9% Isopropyl Alcohol Liquid Cleaner, Clear , 945 mL (1 US Quart) https://www.amazon.com/dp/B005DNQX3C/ref=cm_sw_r_cp_api_jIFPAb1ZECD8F

u/lightfork · 2 pointsr/buildapc

Let them know exactly what happend and seek an RMA if possible as others suggest.

If no RMA is provided, you should clean that socket using high purity isopropyl alcohol. You can normally get it at a pharmacy in "medical grade". Or you can buy electronics grade in aerosol can or liquid to thoroughly rinse out and flush the socket.

u/juanitovaldeznuts · 2 pointsr/chemistry

What you want is anhydrous isopropyl

u/sentkent · 1 pointr/eldertrees

Hmm. okay. I saw a Youtube video that recommended this product, but that was for making an RSO wax/oil consistency, so maybe he used it because all the alcohol is evaporated off..

u/DarkStar851 · 1 pointr/vaporents

Hmm. Your reply isn't showing up in my app for some reason, but I get it from a local warehouse. They get it in huge volume, I get this size bottle (same brand) for $14 CAD. https://www.amazon.ca/gp/aw/d/B005DNQX3C/

Edit: it's not always MG, sometimes it's a different brand but I don't recall the name. I use MG for flux and solder too so I remember the brand.

u/chking999 · 1 pointr/prusa3d

Enabling the 7x7 mode on my MK3 gave me such good bed adhesion that I don't need to use glue stick anymore. Now I just spray the bed with a some 99% alcohol and then print. https://www.amazon.com/gp/product/B005DNQX3C/ref=ppx_yo_dt_b_asin_title_o03_s00?ie=UTF8&psc=1

u/NightmareNeomys · 1 pointr/synthesizers
u/Smokin2k · 1 pointr/NintendoSwitch

MG Chemicals 824-1L 99.9% Isopropyl Alcohol Liquid Cleaner, Clear , 945 mL (1 US Quart) https://www.amazon.com/dp/B005DNQX3C/ref=cm_sw_r_other_apa_i_2aZUDbPD21WNS

I cant find the youtube video I watched to fix my controllers.. it seems to be removed. But a few drops of this stuff (safe to use on electronics - it dries very fast) into the base of the joystick. You have to lift the rubber flap with a toothpick while you apply a few drops. Then just swirl the joypad clockwise and counterclockwise for 30 seconds to a minute. I have fixed all 3 of my controllers with drifts using this method.

u/Cit_the_bed · 1 pointr/overclocking

https://www.amazon.com/MG-Chemicals-824-1L-Isopropyl-Alcohol/dp/B005DNQX3C

It looks like it was in a flood or fire. Odds are the person turned it on and fried it. Your best bet is to save the cpu, the gpus by stripping them down. The motherboard is cheap to get, the ram is probably indestructible... forget the psu exists. You need to really clean the parts well to get the contaminants off. Head to walmart and get gallon jugs of distilled water, and just clean it really really well.

Do you have access to a large ultrasonic cleaner? Fill it with isopropyl and turn it on outside (so there's no fire and explosion risk).

After you use the alcohol to drive the water out, I would clean the gpus twice as the ram is bga, and get a can of pcb contact cleaner and blast it with that when totally done.

I'm pretty sure you can salvage the gpus if the caps are solid caps.

Keep us posted, this looks like fun.

u/Sonicjosh · 1 pointr/gamecollecting

Got mine from Amazon, there's also a bigger bottle on that page that's cheaper, but no sprayer on it.

UK Amazon links

http://www.amazon.co.uk/gp/product/B004SPJP5O/ref=s9_dcbhz_bw_d0_g328_i1_sh

http://www.amazon.co.uk/gp/product/B005DNQX3C/ref=s9_dcbhz_bw_g328_i2_sh

u/JorgJorgJorg · 1 pointr/trees

Everclear will bring through more plant matter because it is only 95% alcohol (or 76% if your state doesnt allow the real stuff). I would highly recommend getting 99% iso from amazon. Dont listen to anyone who says the flavor isnt as good with iso. If you use 99.9%, it all evaporates anyway.

https://www.amazon.com/MG-Chemicals-Isopropyl-Alcohol-Cleaner/dp/B005DNQX3C

If you use everclear, your oil will be an undesireable shade of green due to bringing through the water soluble parts of the plant

u/Red-Fawn · 1 pointr/telescopes

This should work. It's not reagent grade, but I don't think the .09% difference will make a difference in a non-lab setting. The introduced impurities from the q-tip would make it a moot point anyway.

u/KLAM3R0N · 1 pointr/prusa3d

It could be "bad" ipa. Denatured ipa is not good for print bed cleaning. ( a bit on the subject https://sciencing.com/denatured-alcohol-vs-isopropyl-alcohol-5519636.html)

It is probably denatured with a oil based chemical , or has a weird additive, even a residue in the plastic bottle before filling at the factory.... Try another brand and get yourself some 99% ipa MG Chemicals 824-1L 99.9% Isopropyl Alcohol Liquid Cleaner, Clear , 945 mL (1 US Quart) https://www.amazon.com/dp/B005DNQX3C/


I'm personally curious about using DI water(deionized water) to clean instead of 99% ipa, or maybe a 50/50 mix. We use it at work on the industrial printers and it works really good.

u/UnlimitedCashOrgasms · 1 pointr/avb

alcohol will readily evaporate. Once the alcohol has "extracted" (pulled all the good shit) out of the plant matter, just let it sit out for a day or so. Applying heat will accelerate this process. it will evaporate and leave a gooey resin on your plate (or Pyrex dish). scrape (razor blade) and smoke. your done. Aside from golden grain you can also use this. Just don't drink it.

u/rdesktop7 · 1 pointr/3Dprinting

I use acetone on mine.

You can try some anhydrous IPA if you want to try something a bit less harsh.

Try to avoid acetone used for cosmetics, they tend to have things like perfumes in them that will only make your life sad.

Here are links to the fluids I like to use for cleaning:

IPA http://www.amazon.com/dp/B005DNQX3C/ref=biss_dp_t_asn

Acetone http://www.amazon.com/SUNNYSIDE-CORPORATION-84032-1-Quart-Acetone/dp/B000C02AW4/ref=sr_1_8?ie=UTF8&qid=1394475871&sr=8-8&keywords=acetone

Particularly on a hot print bed, make sure you are in a very well ventilated area during use.

u/Roofofcar · 1 pointr/mechanical_gifs

A life changer: anhydrous alcohol. Because it’s 99.9% alcohol, it evaporates essentially on contact when compared with ISO you might have used. I clean flat planes to be joined with a dab on a paper towel, then a microfiber cloth, then a quick jet of air. That might sound like a lot, but it’s genuinely less than 20 seconds per joint in cleaning time.

u/simight · 0 pointsr/sandiego