Reddit Reddit reviews Micro-Mesh 9 Sanding Sheet Introductory Woodworkers Kit with a 2 inch by 3 inch Foam Sanding Block

We found 7 Reddit comments about Micro-Mesh 9 Sanding Sheet Introductory Woodworkers Kit with a 2 inch by 3 inch Foam Sanding Block. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Power Tool Parts & Accessories
Power Sander Parts & Accessories
Sander Sheets
Power & Hand Tools
Power Finishing Tool Parts & Accessories
Micro-Mesh 9 Sanding Sheet Introductory Woodworkers Kit with a 2 inch by 3 inch Foam Sanding Block
Micro-Mesh is a unique cushioned abrasive that produces a very fine and uniform scratch pattern. The nine grades of abrasives range from 1500 grit to 12000 grit. The 1500 is similar in grit range to conventional 400 grit wet/dry sandpaper. The 12000 will leave a scratch pattern that cannot be detected by the human eye and produces a wonderful looking finish. Micro-Mesh abrasives can polish to a high reflective state or leave a matte or satin finish depending upon where you stop.Before starting the Micro-Mesh cycle of abrasive sanding, coarse sanding should be done using up to 320 grit sandpaper. Shaping, sawing or turning of the work piece should be complete.Begin with 1500 Micro-Mesh. Sand until all of the sandpaper scratches are removed. Continue with the MICRO-MESH series and cycle up to the desired look (1800, 2400, 3200, 3600, 4000, 6000, 8000, 12000). Thinned lemon oil or Danish oil can be applied as a finish on bare wood.MicroMesh performs very well in conjunction with polyurethane, polyester, epoxy, lacquer and so on. Follow the manufacturer’s recommended cure times prior to re-coating or applying the finish coat. When you are applying multiple coats, sand from 1500 Micro-Mesh to 3200 or 3600 between coats to remove any orange-peel or dirt. After the final coat has fully cured, polish the surface beginning with 2400 Micro-Mesh and continue through the series (3200-12000) until the desired gloss is achieved.Satin finishes are achieved by sanding up to the 3600 grade. The satin finish gets progressively higher in gloss through the 6000 step. High gloss finishes will appear by the 6000 through 12000 step. The wood, the finish used and personal preference determine where to stop. Micro-Gloss liquid abrasive can be hand rubbed onto the finish following the 12000 Micro-Mesh step for an “ultra” high gloss finish.🇺🇸 This Made In the USA KIT INCLUDES: 1 each of the following grit 3 inch by 4 inch sheets: 1500, 1800, 2400, 3200, 3600, 4000, 6000, 8000 and 12000. Also included is a 2 inch by 3 inch foam sanding block. Micro-Mesh can be used wet or dry.
Check price on Amazon

7 Reddit comments about Micro-Mesh 9 Sanding Sheet Introductory Woodworkers Kit with a 2 inch by 3 inch Foam Sanding Block:

u/crystalmerchant · 5 pointsr/modelmakers

Replied to a similar post recently:

> I did this to a windshield once. Researching fix options was how I learned this technique. Use Micro-mesh sanding pads in this order:

  • 3200 grit - horizontal strokes
  • 3600 - vertical strokes
  • 4000 - horizontal
  • 6000 - vertical
  • 8000 - horizontal
  • 12000 - vertical

    > That should get it transparent, and looking close to glass. Sometimes I then polish with Novus if needed.
u/dicerolla_d20 · 5 pointsr/dice

When I make dice I polished my masters with these. https://www.amazon.com/SANDING-SHEETS-INTRODUCTORY-Peachtree-Woodworking/dp/B000H6HIK2
And when the dice come out of the mold I use them on the sprue marks as well. For the final polish I use headlight restoring polishing with an harbor freight version of a Dremel and a budding attachment.

u/SnarkMasterRay · 5 pointsr/modelmakers

OK.... so in roughly the same order you asked (and I know this will be a long response)....

To me, the paint ratio is more a guide than a formula. I'm looking more for the right consistency than number of drops. Some paints require more thinning than others. Yawningangle mentions Alclad - their paint is formulated for airbrushing, so you don't need to thin it out at all. If the paint in the cup has about the same consistency as milk, it will spray.

I generally use 20-30 PSI, more often the lower values. I like to spray a bit thinner and at lower PSI so that I get thin, even coats with less chance of runs, drips, etc.. The higher PSI values can dry the paint out faster, leading to a pebbly texture on the model.

Masking - I use Tamiya's tape for detail work:
6mm Tape dispenser
10mm Tape dispenser
18mm Tape dispenser
40mm Tape roll
It's a thin rice paper that has more flex than plastic scotch tape and is much thinner than most masking tapes. Good stuff. It will still bubble and ripple over compound curves, but you can work around this by cutting it into thin strips and layering it - see this article for examples.

A dremel works too fast for polishing car models; you'll go through the paint at that speed. It's better to work by hand with some fine polishing clothes. I'm a big fan of Micro-Mesh and you can get starter kits fairly inexpensively that will work great on a project like this.

With regards to the dash - generally, if you're not happy the best thing to do is either live with it or strip it off and start over. It's a big enough pain in the butt that I will sometimes just live with it and leave the windows up or canopy down. ;)

u/Destructias_Warlord · 2 pointsr/modelmakers


If you want to recreate the picture, paint with thinned (you can use water or alcohol) mr.hobby gloss black, silver, and dip the windows in acrylic floor wax. Then you'll need to polish that with some super fine sandpaper, 15,000 grit.

Shopping list:

Tamiya Extra Thin Cement: 5$

Mr. Hobby Gloss Black 4$

Mr. Hobby Silver 4$

Paintbrush set 5$

Sandpaper 25$

• Never get your glue on the windows.
Use something washable for attatching windows like Elmer's Glue.

• Do not paint everything and assemble rather paint as you assemble. Don't get paint on the attatchment points because that will make the cement useless.

Edit: I got the prices on the Mr. Hobby wrong.


u/DavidAg02 · 2 pointsr/AutoDetailing

I think u/TyrantLeo was assuming you bought the Dr. Colorchip kit, which does include everything. However, it looks like you're asking about the dealership touch-up paint.

For that, you want to put the paint on as thin as possible, and in layers. Light coat, let it dry, another coat, let it dry, etc. until you cannot see the bare metal through the paint. Then go over the top with clear coat.

If you want to make it near perfect, invest in an ULTRA FINE grade sanding kit like this: http://www.amazon.com/SANDING-SHEETS-INTRODUCTORY-Peachtree-Woodworking/dp/B000H6HIK2

Ignore the part about woodworking... sand paper is sand paper. This will allow you to really flatten and polish the surface so that the touch up paint blends as seamlessly as possible with the factory paint. I typically only use the 3 to 4 finest grades in this kit when doing touch-ups. You won't be removing much paint at all, and a kit like this allows you to focus on a very small area versus a 6 inch area like you'd have to with a DA + pad. Finish with a light polish and a coat of wax.

u/explodyii · 1 pointr/Shave_Bazaar

The 3k I've found is this one. It works fairly well, but is a bit of a pain on account of the thicker sheet and the texture of the paper itself, which gets caught up sometimes on the surface.

I used to use a micro mesh progression of sanding sheets, which worked great, but my girlfriend threw them out accidentally a couple of months ago and I have yet to replace. The kit I used was this. I definitely start to see a difference the further up in the grit I go, but strictly speaking, you can get a very presentable razor with 600 grit and some metal polish. It won't have a mirror finish, but will still look clean and nice!

u/cgrd · 1 pointr/Pipes

Thanks! :-)
The micro mesh can be a bit hard to find...any specialty wood working store should carry it, but it's available online.


http://www.amazon.com/MICRO-MESH-SOFT-TOUCH-SANDING/dp/B000H6EC4C


http://www.amazon.com/MICRO-MESH-SANDING-SHEETS-INTRODUCTORY/dp/B000H6HIK2


http://www.leevalley.com/en/wood/page.aspx?p=62127&cat=1,42500

A cheaper method would be to start with a very fine steel wool, and then use a nail buffer, which is essentially a nail file with micro mesh on it...the "shine" side will be the finest. Both of these could likely be found in Walmart, etc.