Reddit reviews Mitutoyo 050103, Edge/Center Finder, 3/8" Diameter Shank, 0.200" Diameter Tip
We found 2 Reddit comments about Mitutoyo 050103, Edge/Center Finder, 3/8" Diameter Shank, 0.200" Diameter Tip. Here are the top ones, ranked by their Reddit score.
Used in a milling machine to find the workpiece edgeAll working surfaces are hardened and groundCenterfinder end is used to find hole centers, and aline the spindle with a punch mark or scribed line
Uh, pretty sure the pointed end is a "center finder". That's what I use it for anyway.
http://youtu.be/06IGyn84lmE?t=1m23s
That's what Mitutoyo says it is.
You have a good idea too there though, but I don't think that situation comes up enough to warrant slapping one on the back of your edge finder.
I own a Craftex CX-601, which is a very similar machine to the one you've decided on.
On the vice, I would recommend either buying a vice that someone else owns and can confirm is good...or only buy one you can see in person. I bought a 5 inch Taiwanese vice, and I'm pretty disappointed with the quality of it. It was on-sale, and I figured it would "do fine" while I looked for a Kurt or other super nice unit on Craigslist. Turns out it does "do fine", but the moveable jaw was shimmed instead of machined square. Not good. On my table a 5in vice is a good size, but I probably could have gone with a six. Consider upsizing yours to a 5in vice.
It's worth looking to see if you have any tool shops nearby that carry milling machines, even ones of a different brand. Armed with your machine's measurements you can find a "similar" sized bed on a floor model and see what a 4, 5 and 6in vice will look like. That's what I did before ordering both my mill and my vice size.
All the clamping kits are basically the exact same in the box, probably from the same company. Shop around, you can save even more money:
http://www.amazon.com/Anytime-Tools-Slot-CLAMP-CLAMPING/dp/B007DMLBRE?ie=UTF8&keywords=clamping%20kit%201%2F2%20t-slot&qid=1458758346&ref_=sr_1_6&sr=8-6
http://www.harborfreight.com/58-piece-combination-step-block-and-clamp-set-3-8-eighth-inch-16-nc-studs-1-2-half-inch-clamps-5952.html
I own that end-mill set, very happy with it.
You have two edge finders listed, a Mitutoyo edge finder and a Fowler edge and centre finder. You only need the one combo unit, and this Mitutoyo is cheaper: http://www.amazon.com/Mitutoyo-050103-Center-Finder-Diameter/dp/B002SG7PPM/ref=sr_1_1?ie=UTF8&qid=1458758586&sr=8-1&keywords=edge+and+center+finder
You are missing a holder for your horizontal dial indicator, which I'm presuming you're ordering for squaring up your head to the table, and your vice to the table. The magnetic base you have is great for checking run out of the spindle, and movement of the work, but not ideal for squaring up the head. I started with a clamp like this:
http://www.amazon.com/HHIP-4401-0401-Universal-Indicator-Holder/dp/B01BHHY92E?ie=UTF8&keywords=universal%20indicator%20holder&qid=1458759060&ref_=sr_1_21&sr=8-21
Which I wasn't too happy with. It works, but it's pretty easy to upset the clamp alignment and you have to start over. I have since ordered this unit: https://www.accusizetools.com/egaa-z986-zero-set/ but haven't had a need to re-square my head or vice yet. Doesn't look like it's available on Amazon though.
I notice the mill you're looking at has the option to add the X-axis power feed for $299. If you can stretch the budget, definitely go for it. I figured I would "add one later" and even though I still plan on doing so, man am I cranking away on that handle a whole lot.
It's not cheap, but I find this set of drill bits to be quite handy: http://www.amazon.com/Woodtek-928828-Boring-Machinist-Titanium/dp/B008RE2CSY/ref=sr_1_6?ie=UTF8&qid=1458759539&sr=8-6&keywords=115pc+drill+bit+set