Reddit reviews Moody Tools 58-0670 6-Piece Slot/Phil/Screw Extractor Combo Reversible Driver Set

http://www.amazon.com/Moody-Tools-58-0670-Extractor-Reversible/dp/B000JCT3W0

Get an extractor kit, something like this or this.

They don't?

I'd give this one a shot. https://www.amazon.com/Moody-Tools-58-0670-Extractor-Reversible/dp/B000JCT3W0/ref=sr_1_4?keywords=MOODY+screw+extractor&qid=1555039644&s=gateway&sr=8-4

​

That's how I removed the motherboard of my MBP. I stripped the heads of at least 6 motherboard screws, pretty much ground them to a cone with my regular phillips drivers. These ones took a bit of patience and finger skills, but got everything out.

I almost stripped the screws on mine as well while trying to unscrew with a cheap screwdriver. I ended up getting this: Moody Tools 58-0670 6-Piece Slot/Phil/Screw Extractor Combo Reversible Driver Set. I managed to get them out with just the driver, but I am sure the extractors will come in handy at some point.

Lots of choices for normal sized screw extractors. For the really small ones, give this set a try. (available from other vendors incl brick'n'mortar places).

http://www.homedepot.com/p/Ontel-Speed-Out-Speed-Out-Screw-Extractor-4-Piece-1000264/205110987

https://www.amazon.ca/58-0670-6-Piece-Extractor-Reversible-Driver/dp/B000JCT3W0

Moody Tools 58-0670, or in silver.

You'll need to use something like this. http://screwremover.com/Pages/grabitMicro.php You may want to measure the screw to see if these are small enough.

EDIT: Amazon has another company if you search for "grabit micro" The additional photos showed a person who had to remove stripped screws from an Apple notebook/cellphone. http://www.amazon.com/Moody-Tools-58-0670-Extractor-Reversible/dp/B000JCT3W0/ref=sr_1_6

Hey, just wanted to add an update to this in case anyone else runs into the same problem I have. I was almost to the point where I was going to take a drill to the chromebook! :O

Luckily I found Moody Tools Precision Screw Extractor on Amazon.

They worked like a charm and the stripped screws were out in just a few minutes!

Ok depends on they type of Barrel. If it is is a standard german barrel with screws protruding I would recommend this tool:
https://www.amazon.com/gp/product/B0052XQYVO/ref=oh_aui_detailpage_o00_s01?ie=UTF8&psc=1.
It is very good at grabbing the sides of exposed screws.

If the screw is flush with the service you might have luck with these:
https://www.amazon.com/gp/product/B000JCT3W0/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1
you have to be able to put a lot of pressure on the screw head so make sure it is resting level on the desk.

Here is a hand set that way you don't have to buy a drill.

For future situations you could keep a set of 'left handed' drill bits, these bits cut by spinning counterclockwise, giving the screw a chance to come loose. But really you should have a screw extractor, ones this small are hard to come by (#0 or #00) but they do exist:

http://www.amazon.com/Moody-Tools-58-0670-Extractor-Reversible/dp/B000JCT3W0/

If you're going for the cheap hex key + JB weld route check out your local hardware store.

Cheapish screw extractor set to try: https://www.ifixit.com/Store/Tools/Precision-Screw-Extractor-Set/IF145-118-1 or https://www.amazon.com/Moody-Tools-58-0670-Extractor-Reversible/dp/B000JCT3W0; reviews are mixed on these though.

For power tools, there are a couple of different options:

• Dremel / rotary tool: your best bet is probably to get a very small diamond burr kit and slowly mill a slot into the screw head that a flat-head driver could catch. A cutting wheel could also do this but you'd definitely damage things around the screw. Amazon sells these, as would your local hardware store.
  
• Drill: I'm not sure if they make small-enough left-handed bits for this, but that's normally what you'd use to get out stripped screws. Barring that, you can drill straight through the screw (which will damage the standoff; get ready to use epoxy or VHB to secure the replacement part in place), Again, hardware store or Amazon.

you could try a screw extractor. I am not familiar with the spyderco deleca 4 knife, but based on googling reviews it seems like it would withstand a fair amount of pressure.
Try something like this:
http://www.amazon.com/58-0670-6-Piece-Extractor-Reversible-Driver/dp/B000JCT3W0/ref=sr_1_2?ie=UTF8&qid=1342137683&sr=8-2&keywords=screw+extractor+set

I've used these in the past with great success. You can hammer and glue them in as well.

https://www.amazon.com/Moody-Tools-58-0670-Extractor-Reversible/dp/B000JCT3W0/ref=sr_1_1?ie=UTF8&qid=1492731155&sr=8-1&keywords=precision+screw+extractor

aw man.. yeah it's really tough to extract stripped screws.. don't give up just yet though, there are extraction kits out there, even for tiny screws like this or this