Reddit Reddit reviews NuTone NFS20Z Smart Z-Wave Enabled Isolated Fixture Mounted Control, White

We found 9 Reddit comments about NuTone NFS20Z Smart Z-Wave Enabled Isolated Fixture Mounted Control, White. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Electrical Equipment
NuTone NFS20Z Smart Z-Wave Enabled Isolated Fixture Mounted Control, White
Operate and control virtually any electrical device or appliance from anywherePerfect for Commercial Lighting, Dry-Contact Relays, Pool Pumps, Water Heaters, or In-Ceiling LightingMounts in an electrical boxWorks with other Z-Wave devices in your home to ensure full coverageNetwork wide inclusion for easy setup
Check price on Amazon

9 Reddit comments about NuTone NFS20Z Smart Z-Wave Enabled Isolated Fixture Mounted Control, White:

u/TheDiscordium · 4 pointsr/SmartThings

I have two of these devices for controlling my garage doors.

NuTone NFS20Z Smart Z-Wave Enabled Isolated Fixture Mounted Control, White https://www.amazon.com/dp/B00WXLRF2U/ref=cm_sw_r_cp_api_mXKRAbX1N0YGB

There is also a similar model by Linear and GoControl.

I was thinking about using another to control my fireplace, but I am hesitant to connect that to SmartThings.

u/bymyhand · 3 pointsr/smarthome

I have an enclosure and I replaced my timer with this:

NuTone NFS20Z Smart Z-Wave Enabled Isolated Fixture Mounted Control, White https://www.amazon.com/dp/B00WXLRF2U/ref=cm_sw_r_cp_apa_i_gn1CCbKSH1BWE

Zwave Pool Timer Replacement

u/Waffle_bastard · 1 pointr/homeautomation

Neither the fan nor light have wall switches - they both receive straight power, and their only controls are pull switches on the fan itself.
I just got done pulling the cowl off of the fan to take a look at the wiring, and it has four wires. Based on some wiring diagrams online, this seems to be standard, and an encouraging development. I'm considering wiring in a Z-wave fan controller like this one ( https://www.amazon.com/gp/aw/d/B00WXLRF2U/ref=mp_s_a_1_1?ie=UTF8&qid=1503442019&sr=8-1&pi=AC_SX236_SY340_QL65&keywords=zwave+fan+controller&dpPl=1&dpID=41mCd9NGH6L&ref=plSrch ), and just sticking it up inside the attic.

u/MyOther_UN_is_Clever · 1 pointr/homeautomation

So assuming you have seperate wires for light and fan motor, you need a smart switch for LEDs (assuming LEDs), and a seperate smart switch for fan motors. https://smile.amazon.com/MOES-Ceiling-Control-Compatible-Required/dp/B07HQ95N69/ref=sr_1_9?keywords=wifi+ceiling+fan+controller&qid=1555516380&s=gateway&sr=8-9

You can also get a smart universal controller, which is a little box you wire into the fan housing, and pretty much all fans are designed to fit one (hence universal). https://smile.amazon.com/NFS20Z-Enabled-Isolated-Fixture-Mounted/dp/B00WXLRF2U/ref=sr_1_15?keywords=wifi+ceiling+fan+controller&qid=1555516380&s=gateway&sr=8-15 The downside to this option is you can't control either from the wall switch (except on and off).

I haven't done too much looking, yet, but I do know that fans are usually 3 or 4 speed, so I'd look for switches that match (as opposed to ones that let you set any voltage). The motors are engineered to specifically run at certain speeds (it's a frequency thing).

For everything to work properly, the pull chains need to be set to max speed, max brightness. I recommend not adding the extensions that are often included, so people don't mess them up on accident.

u/FunkyPickleSmell · 1 pointr/smarthome

My gas fireplace is already wired to a dumb light switch.

I wouldn’t foresee any problems converting that switch to a smart switch and seeing the same on/off behavior.

If yours isn’t wired into a light switch already then I’d look for a z-wave inline switch like the one I used on my garage door: https://www.amazon.com/dp/B00WXLRF2U/ref=cm_sw_r_cp_api_4krUAb8FJHWKB

u/HomeSeerMark · 1 pointr/homeautomation

OK based on the wiring diagram, the included fan speed switch relies on separate wires to power the motor for different speeds. This would rule out using a conventional Z-Wave fan controller as those simply change voltage to regulate speed. If you want Z-Wave managed speed control, you'll need to cobble together Z-Wave activated fixture modules (like this one). On the other hand, if you'd be content to manually control the speeds and want to use your automation system to turn the fan on and off, a Z-Wave smart switch or receptacle would work.

u/bacon_slice · 1 pointr/smarthome

NuTone NFS20Z Smart Z-Wave Enabled Isolated Fixture Mounted Control, White https://www.amazon.com/dp/B00WXLRF2U/ref=cm_sw_r_cp_apa_CQ.2AbTHN7542

u/Anydudewilltellyou · 1 pointr/smarthome

I control all my Z-wave switches, lights, etc with a hub. Then Alexa talks to that.

Allegedly, Z-wave works with Alexa, but I've never tried it direct. Others should chime in here.

For your fan, this may work for you:

https://www.amazon.com/NFS20Z-Enabled-Isolated-Fixture-Mounted/dp/B00WXLRF2U

u/MagnusTheRabbit · 1 pointr/homeautomation

Is it a ceiling fan? If so:

You would replace the box that communicates with your current remote with something like this. Note I am not endorsing that specific product at all as I have no experience with it.