Reddit Reddit reviews Simpson Strong Tie FPBB44 Black Powder-Coated 12-Gauge E-Z Base

We found 4 Reddit comments about Simpson Strong Tie FPBB44 Black Powder-Coated 12-Gauge E-Z Base. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Building Supplies
Building Materials
Decking & Fencing
Fencing Railings & Pickets
Decking Posts & Accessories
Simpson Strong Tie FPBB44 Black Powder-Coated 12-Gauge E-Z Base
Allows easy installation of 4x4 wood posts on existing concreteEasy to install in concrete with 1/2 in. diameter anchorsMade from 12 gauge steelBlack Powder-Coat. Post bases do not provide adequate resistance to prevent rotation about the base and therefore are not recommended for non-top-supported installations such as fences or unbraced carportsInstall with 1/4 in. SDS screws or 1/4 in. HDG lag screws
Check price on Amazon

4 Reddit comments about Simpson Strong Tie FPBB44 Black Powder-Coated 12-Gauge E-Z Base:

u/[deleted] · 3 pointsr/DIY

Do you mean patio? :P


Easy enough. Get one of these then do the hammer drill thing. For bolts in to the concrete either use the wedge anchor or set some bolts in with epoxy. Probably wise to use stainless steel for all your bolts.

u/robert_cortese · 3 pointsr/SanJose

>That's a gorgeous fence

My wife would digress, she says the curve isn't centered. 2 flats on one side, 3 on the other.

>I am an idiot

C'mon you run trivia nights, I've seen you post here plenty. There are true idiots on this sub, and you're not one of them (IMHO)

>don't know if I could actually do that.

Don't know until you try. I didn't know until I tried, but I had some fencebuilding experience when my family still had ranches (mostly the old men yelling at me to carry wood, sand, nail, no cutting)

This is how I did it. Maybe I can lend a hand, I dunno. You'd have to entertain my wife and kids and maybe feed us or something. Maybe you could do the same for us sometime.

Tools: (mostly cheap harbor freight)

  • Miter box saw. This let's you cut fairly precise angles.
  • Jig Saw. For finishing the curve on top.
  • Drill. For putting things together
  • Hammer Drill. For drilling in cement anchors (Mine is freestanding, not attached to the fence or house)
  • String, for making that swooshy curve.

    I started off by measuring. Once I had my measurements in, I took a long hard look at my neighbors fence (we have that picture) and copied the framing. I scaled it for my entryway.

    Once I had the basic design down, I drilled in my post cement anchors. I used 4 of these Simpson Strong Tie Fence Anchors. Even after a year, the fence is still as strong as the day I made it.

    After I had my posts up, I put the J screw hinge onto the posts and connected some cross members so the posts would shore up against each other.

    I took what would become my gate frame, and put the other half of the j screw hinge in. Then I did one final measure now that I knew how much space the hinges took up.

    Pulled the 4x4's off the hinge post, and built out the rest of my frame. I made sure to leave plenty of room at the bottom for the gate to swing freely. After the frames were complete, I re-hung them on the J hooks.

    Once the frames were up, I began skinning them. I laid a 4x4 at the bottom to give myself spacing (Didn't want the skin scraping) and put up fenceboard. Throughout this entire process, I used deck screws with the star bit. These bits don't slip, and the screws are coated to sort of self lubricate themselves through the wood.

    After all the skin was up, I tied a string to where I thought was center at the bottom of the fence. I stretched the string to the top of the fence and tied a crayon to it (just didn't have a pencil) The string acts like a giant compass, and let me make a nice even arc.

    Finally, I took a hand held jig saw and sawed along the line at the top making that nice curve.

    Only took me a day to knock it out.

u/chrisbrl88 · 1 pointr/HomeImprovement

Dig a hole 2 feet deep (minimum), pour a footer using an 8" tube form, and use a post base. You can set the base and put the anchors into the concrete while it's still wet to avoid having to drill (just make sure you get it plumb using a torpedoes level). It'll run you all of fifty bucks. The EZ base is the most expensive part.

u/Hedsteve · 1 pointr/DIY

Fill the buckets and then install brackets on top.

brackets on Amazon