Reddit reviews Stanley 33-425 25-Foot by 1-Inch Measuring Tape

We found 8 Reddit comments about Stanley 33-425 25-Foot by 1-Inch Measuring Tape. Here are the top ones, ranked by their Reddit score.

16-Inch and 19.2-Inch stud center markings7-Foot standout25-Foot length1-Inch width

Check price on Amazon

8 Reddit comments about Stanley 33-425 25-Foot by 1-Inch Measuring Tape:

u/rompenstein · 9 pointsr/Tools

Here's what I would personally recommend for a decent minimum starter set, assuming you're just looking for general homeowner/handywork tools:

5-in-1 screwdriver
16 oz. claw hammer
6 in. adjustable wrench
Measuring tape
Allen wrenches
Pliers

Those are all solid quality tools that I've personally used in the past. There's obviously tons of other stuff you'll need along the way if you're into fixing things but that's a great starting point.

u/coherent-rambling · 5 pointsr/BeginnerWoodWorking

Here's what I would buy if I were equipping my garage workshop on a budget from scratch today:

Table Saw - Unless you go for hand tools, this is the absolute core of your shop. Do not buy a new saw for less money than this under any circumstances, because it's false economy and you'll soon outgrow it. You may wish to buy a cheaper used model, in which case you should shop for a Craftsman 113 (aim for a belt drive rather than direct drive) on Craigslist. Spend up to $150 and plan to build or buy a better fence in the first year, which will bring you up to roughly the same capability as the new saws.
Drill and Driver - You need a drill anyway. Everyone does. This is nothing fancy, but it's a tolerable set that should last a hobbyist quite a while, and both batteries and extra tools are cheap. Grab a set of drill bits and a few impact-rated screwdriver bits, or a fancy combo set of both.
Miter Saw - Indispensable for cutting long pieces. You may eventually wish to get a big 12" sliding monstrosity to make wider pieces easier to work with, but you can also do that with a table saw. I suggest an inexpensive variant of the most basic type of miter saw to start, so you've got a good foundation to work from but don't have a ton of sunk cost if you upgrade later.
Circular Saw - You'll use this for breaking down sheets of plywood bigger than your table saw can handle. You can also use it as a stand-in for the table saw for the first few projects. I'm recommending a lightweight cordless model for convenience during these simple, short tasks, but if you work with thick materials you may eventually want a powerful corded one as well - I've got a cordless and then a monstrous 15-lb worm drive saw for heavy duty use. If you just want to split the difference right off the bat and have one tool that's okay for everything and not great at anything, get a basic corded one.
Jigsaw - For cutting curves and small notches. Make sure you get one with orbital motion, but other than that you can go pretty cheap on this because you won't use it that often. However, buy top-of-the-line blades; I really like Bosch blades.
Router - This is a very capable middle-of-the-road router. You'll eventually want to add a plunge base, and might add a lightweight trim router to make edge profiles more easily. You can get accessories to expand on this, or you can eventually dedicate it to a router table and buy new for those other things - the variable speed motor on this is ideal for table use.
Sander - This is the most general-purpose sort of sander, although it's a little on the aggressive side for final sanding. Just hand-sand where you need more finesse until you know what other sanders you might want.
Combination Square - Use this for laying out cuts and holes and stuff.
Speed Square - That blue book will show you tons of neat tricks with this square. Mostly you're going to use it as a short guide for the circular saw, though.
Tape Measure

Edit: Looks like that's about $1,100.00 depending on your local tax rate and how much of it you can slip past untaxed. That's steeper than I expected, but it's also an entire barebones shop for less money than the table saw I really want.

u/83drew · 5 pointsr/cars

https://www.amazon.com/Stanley-Powerlock-25ft-Tape-Rule/dp/B00002X2GQ/ref=sr_1_3?ie=UTF8&amp;qid=1501611122&amp;sr=8-3&amp;keywords=tape+measure

u/CR3ZZ · 4 pointsr/Machinists

Those are nice but this is a far more accurate caliper

https://www.amazon.com/gp/aw/d/B00002X2GQ/ref=mp_s_a_1_3?ie=UTF8&amp;qid=1495863708&amp;sr=8-3&amp;pi=AC_SX236_SY340_FMwebp_QL65&amp;keywords=tape+measure&amp;dpPl=1&amp;dpID=41RWEfPSKQL&amp;ref=plSrch

It's used for precision inspection by real machinists!

u/TornadoDaddy · 2 pointsr/funny

Perhaps you should consider buying one of these before your next big purchase

http://www.amazon.com/gp/aw/d/B00002X2GQ/ref=s9_top_hm_b2Jvw_g469_i1

u/road_warrior_1 · 1 pointr/Carpentry

A saw, drill with bits, measuring tape.

These are some of the tools I have. They are, admittedly, more aggressive than what you might need for your first project but it should give you an idea of were to start from.

u/reg_sized_rudy · 1 pointr/Fitness

This recent invention could help you finally determine your accurate height: you're welcome

u/TheLegendOf1900 · 1 pointr/GentlyWeepsPlayers