Reddit Reddit reviews StarTech.com 15.7 in (400 mm) SATA Power Splitter Adapter Cable - M/F - 4x Serial ATA Power Cable Splitter (PYO4SATA), Black

We found 77 Reddit comments about StarTech.com 15.7 in (400 mm) SATA Power Splitter Adapter Cable - M/F - 4x Serial ATA Power Cable Splitter (PYO4SATA), Black. Here are the top ones, ranked by their Reddit score.

Computer Accessories & Peripherals
Computer Cables & Interconnects
Electronics
Computers & Accessories
SATA Cables
StarTech.com 15.7 in (400 mm) SATA Power Splitter Adapter Cable - M/F - 4x Serial ATA Power Cable Splitter (PYO4SATA), Black
Add three extra SATA power outlets to your Power Supply – SATA to SATA Power Cable – SATA Power Splitter Cable – Serial ATA Power Splitter1x SATA Power Plug to 4x SATA Power ReceptacleSATA Power Splitter Cable AdapterDurable construction
Check price on Amazon

77 Reddit comments about StarTech.com 15.7 in (400 mm) SATA Power Splitter Adapter Cable - M/F - 4x Serial ATA Power Cable Splitter (PYO4SATA), Black:

u/Codaii · 13 pointsr/CableManagement

On break at work so i’ll make this quick. Most motherboards come standard with these but there are outliers. Looked these up quick just to give you an idea. The right angle side of the cable would plug into your drives and should help you keep away from bending your cables with the back panel. Hope this helped.

Data cables

Power cables

Edit: These are also good to use.

u/fleton · 9 pointsr/DataHoarder

A fast and easy option is get a sata power spliter. Just snip the last wire which disables the 3.3v pin and they work perfectly fine. It is what I did.

u/Not_So_Invisible_Man · 8 pointsr/DataHoarder

If you care about your disks or are using certain enterprise drives you should be using decent quality sata to sata splitters such as https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E

Some drives have issues if they don't have the extra 3.3v leg.

u/Not_the-FBI- · 6 pointsr/DataHoarder

Sure, this one. I needed 4 sets to get enough connectors for all my drives. Take the back cover off of the connector, its just clipped on. Pull the wire up from both sides to keep the metal connector in place. Repeat for all the connectors. Then put your drives in your caddy or whatever you're using, put the empty connectors on the drives, then run your new wire across all of them for perfect spacing. I used new 18ga wire, but you could reuse the old too. Skip the wire for the 3.3v line, then get a flathead screwdriver out and push the wire into the connectors. Do the same for the female connector with however much spacing you want, then just put the back covers back on and you're all set.


All in all I think it took me an hour or so to do my 3 caddies. Once you figure out how to do it it goes pretty quick. Super easy as well, just make sure to double check you have the female connector the right direction so you're not reversing the pins power and killing your drives.

u/FruitGuy998 · 5 pointsr/DataHoarder

https://www.amazon.com/dp/B0086OGN9E/ref=cm_sw_em_r_mt_dp_U_MSWBCbH62Y3RM

I got that it's been working great on my shucked easystores.

u/D2MoonUnit · 4 pointsr/DataHoarder

Those look pretty molded to me too. I use these ones, myself:
https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E

The connector is upside-down, so it's a bit of a pain to use, but I'm only using 2 of the 4 slots at the moment.

u/Droid126 · 4 pointsr/DataHoarder

I'm running 10 drives on my corsair CX500M. it only has a single 12v rail. its also powering my 1080. I have had zero problems for 2.5 years now. I use these. they are amazing and high quality.

u/solomoncowan · 4 pointsr/buildapc

In no circumstances should anyone use molex to sata use this instead.

u/g_l_e_n · 4 pointsr/techsupportmacgyver
u/TripKnot · 3 pointsr/unRAID

While the capacitor in those Silverstone cables are suppossed to help even out power as drives spin up, the capacitor quality apparently isn't good (eg ChengX).

I used to use those cables until I read a post on the unraid forums where a user was experiencing multiple drive failures and solved it by removing the CP06 adapters.
I ended up swapping the silverstone adapters out for 1x4 StarTech adapters:

https://www.amazon.com/gp/product/B0086OGN9E/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1

u/ss0889 · 3 pointsr/JDM_WAAAT

You can buy a bunch of these, dismantle, and reassemble without the 3.3v wire. Makes for a really clean cable too.

StarTech 4X SATA Power Splitter Adapter Cable https://www.amazon.com/dp/B0086OGN9E/ref=cm_sw_r_cp_apa_i_pQDTCbTN3408G

https://images.app.goo.gl/wbW4z7TGCrhF8bZn9

u/astro143 · 3 pointsr/buildapc

StarTech.com 4x SATA Power Splitter Adapter Cable (PYO4SATA) https://www.amazon.com/dp/B0086OGN9E/ref=cm_sw_r_cp_api_lkZxybFHC9CZ1


I just bought one of these for that exact reason. Use it as an extension for the optical drive

u/boostdd · 3 pointsr/JDM_WAAAT

Here is my custom SATA power splitter. The top (5th) connector was added afterward. Notice how the rightmost wire is missing, that's the 3.3v wire. https://i.imgur.com/w7FqbFy.jpg

Some folks add the main male connector in between the drive connectors, instead of leaving a short length at the top or bottom (like mine).

Keep in mind that the splitter comes with 4x connectors, so you have to order an extra one in order to complete the row of 5x connectors. So if you have the Rosewell 15x bay chassis, you'll need to order four splitters.

u/defenceplox · 3 pointsr/DataHoarder

For the sata power you just need something like this;

StarTech 4x SATA Power Splitter Adapter Cable https://www.amazon.co.uk/dp/B0086OGN9E/ref=cm_sw_r_cp_apa_C-eczb8V3CKRY

u/ruralcricket · 3 pointsr/DataHoarder

These are crimped.

https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E/ref=sr_1_1_sspa?keywords=sata+power+splitter&qid=15512362


But before going further...

  1. can you hear it spin up?
  2. Have you checked in diskmgmt.msc and initialized the disk?

    If you have 4 wires in your power cable it shouldn't be the 3.3v issue as the 4 wires are 12v, 5v, and two ground leads.

    If you have 5 wires, the wire closest to the notch in the connector is the 3.3v lead.

    https://imgur.com/a/tW8NDP4
u/CollateralFortune · 3 pointsr/homelab

All that stuff is.

Something like this is crimped. This too

u/wlhlm · 3 pointsr/homelab

I recommend using SATA power splitters.

u/kladze · 3 pointsr/DataHoarder

i have used regular tape aswell as gaffa tape...

a better and proper solution (if you have multiple drives like this) would be to get a sata splitter and then remove the cable that "covers" the pins for 1-3... i just got myself these https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E

Now where each "sata plug" is... you can open the cap remove the wire so it only have 4 wires and then you dont need to do the 3.3v mod anymore and then pop the cover back on.

u/cf18 · 3 pointsr/buildapc

https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E/

The easiest solution is to get a SATA splitter. Modular PSU power cables must match the PSU model.

u/Nyteowls · 2 pointsr/DataHoarder

https://www.amazon.com/gp/product/B0086OGN9E/
Safer to use the daisy chained ones, since specific power supply cables dont mix well with other brands and sometimes even different models of the same brand, you can fry your HDD+power supply. You can only daisy chain so much, so you'd probably want to research and calculate what the maximum amount of HDD off of one main power supply cable is.

u/D-J97 · 2 pointsr/pcmasterrace

Not saying you should do it, just showing you you can get up to 4 way splitters: https://www.amazon.co.uk/StarTech-B5196-Power-Splitter-Adapter/dp/B0086OGN9E

u/wintersdark · 2 pointsr/JDM_WAAAT

You want to get well made ones. Look for brand names, not the cheapest you can find. The problem ones are the really cheap ones, which are characterized by molded SATA connectors - the wires terminate inside the molded SATA power plug. [These ones are very unreliable.](
https://www.amazon.com/Cable-Matters-3-Pack-Molex-Power/dp/B00STNUB04/ref=mp_s_a_1_3?crid=3D7AP1AE1TFLT&keywords=molex+to+sata+power+adapter&qid=1555423096&s=gateway&sprefix=molex+to+sata&sr=8-3)

Edit: I use "cheap" too much here, there are good inexpensive ones such as I link below, so don't use price as a rating.

The good ones sort of clamp onto the wires. or have crimped pins.

Here's a video that shows what to look for: https://youtu.be/TataDaUNEFc

u/freakingwilly · 2 pointsr/pcmasterrace

Don't use molex to SATA. There is a reason why "molex to sata fire" is one of the top hits when you Google "molex to sata".

Buy a SATA power splitter instead.

u/Af87l · 2 pointsr/DataHoarder

That power supply has a whopping 6 SATA outputs. You should be able to use 2 or 3 of these with no problem: StarTech.com 4 Outlet SATA Power Splitter Adapter Cable - SATA Splitter Cable - SATA Adapter - Black - SATA Splitter - (PYO4SATA)

I would be hesitant to chain them all together into an 11x cable. Is there some particular reason why you need a single cable for all your drives?

u/kramer314 · 2 pointsr/buildapc
u/Flu17 · 2 pointsr/buildapc

What wattage is your PSU? SSDs don't take much power, so you could probably use a splitter. Also, don't your SATA power cables have multiple connectors on each cable? The ones that came with my PSU look like the ones in this picture:
https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E/ref=pd_lpo_147_lp_img_4?_encoding=UTF8&psc=1&refRID=MXNGKRM3TBJEM0N5YYM4

u/BergOfStein · 2 pointsr/techsupport

That makes it a bit more difficult. I would need to see a picture of the inside of your computer.

Basically you are looking to see if there is an additional power cable in the case that looks like this. It should be attached to the chord that is attached to your SSD that is already in the computer.

If there is an extra power port already available then you will just need to buy an additional data cable to install the new HDD.

Here is a pretty simple brake down on how to do the rest. I would watch a YouTube video as well to see the whole process in action. You will need to buy some screws to secure the HDD to the slots in the computer. Ask a local computer store, they will be able to help.

It is basically close to plug and play, like an external drive, but a few extra steps and it is internal.

u/Coplate · 2 pointsr/DataHoarder

You can get one of these, that isn't molded, and just remove the 3.3v wire, if you want to have it handy for this kind of drive, if you dont want to use a molex adaptor

StarTech 4X SATA Power Splitter Adapter Cable https://www.amazon.com/dp/B0086OGN9E/ref=cm_sw_r_cp_apa_i_kZE3CbNH7J2V8

The 3.3v wire is the one closest to the "L" on the plug part.

With this kind, you can always keep the wire, and put it back in later if you need it.

You can buy this kind and take the plugs off. And add them to your existing wires too! That's how I made mine that are exactly the right length for all 6 drives in my case. You just need a small flathead and patience. Or a normal punch down tool

u/Mel--Gibson · 2 pointsr/techsupport

My computer only has 2 sata power plugs, but I have 8 drives that use sata power. I got a couple of these

https://smile.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E/

u/broken_cogwheel · 2 pointsr/DataHoarder

I don't know of any guides, but for the home user, it's really not expensive or difficult.

What you need, besides HBA in your host machine, is just a bunch of cabling. If you don't have an HBA...cheap and available on ebay.

Just an FYI: Most hard drives don't use a lot of power. (you can look up the max power requirements for specific drives through their manufacturer spec sheet) A 500 watt power supply can often supply the vast majority of that over the 12v rails. Your power supply can run many more disks than it has provisions for, so splitter cables are often the only way to maximize your chassis disk space. As I mentioned before: don't use cables with molded connectors. Cables like https://www.amazon.com/gp/product/B0086OGN9E - you can see they are plastic and snap around the cables themselves and aren't a molded piece.

The super quick and dirty to expand your storage past your server computer's space or power capabilities is:

u/thewebdev · 2 pointsr/india

No, I didn't mean if your mobo supports the processor. Every processor has a different cooling requirement. So you have to use the correct heatsink and fan with it to ensure that the CPU cools correctly. Your current CPU's sinck and fan may not be suitable for the new CPU. You need to do some research on this.

I got confused about the power part. You just need to buy ONE power cable that can support 2-3 HDD. Something like this one. (And make sure your SMPS can provide enough power).

u/rehpotsirhc123 · 2 pointsr/pcmasterrace

It's definately not BTX but it also doesn't look standard ATX. I would get this or this and call it a day

u/petehackett101 · 1 pointr/pcmasterrace

These are the ones I was thinking of getting:

https://www.amazon.co.uk/gp/product/B0086OGN9E/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

Looks like they are the better option you suggested?

u/billyvnilly · 1 pointr/unRAID

you buy this cable: 4x SATA splitter cable
each of the adapters actually has a plastic housing on the back that you snap on and off. You unsnap the housings and literally rip out the 3.3v wire (the 1st wire, on the notch/elbow side). Snap the housings back on, and done.

u/korpo53 · 1 pointr/homelab

I've done servers with cables like that first one (though from Monoprice, I think), and they work fine. I used power cables like this, though you may have to find ones that bend the right directions or something for your use case.

I think that red/black cable is to hook your SAS card up to the board, or lights, or something so you the blinken lights on the front of your server. Not really necessary.

u/GGATHELMIL · 1 pointr/freenas

https://www.amazon.com/gp/product/B0086OGN9E/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1


these all the way. they are rigid too so if you bend them they stay for the most part.

The R5 was on the table. actually better suited since it has the Perfect amount of bays. but that price tag ughhh. Also this case would be cool for a daily driver case. It has a hot swap 3.5 drive bay on the top. its weird to see on a case

u/Reuuk · 1 pointr/homelab

I did get more than 4 drives installed, I have 4 in the hot swap bays and one SSD that is sitting inside the case that I run my windows server on. The SSD is just hooked up to a SATA port on the motherboard, as for power I bought a sata x1 -> sata x4 connector and I am using that to power the drive. The system treats it just like a normal drive at this point and it's working just like I want it to.

I bought a H700 on ebay for ~$100 and just swapped it out and it came with a new cable that just hooked up to the back on the backplate on the hot swap bays. Raid controller takes care of my 4x4TB drives set in raid 5 with ease, no issues there.

I think I hit all your questions, feel free to let me know if this is confusing.

u/kamillion2000 · 1 pointr/computers

If you have an existing SATA power cable you can use a splitter similar to this one they also make them for the Molex power connectors

u/lunarsunrise · 1 pointr/homelab

Pretty much no power supply is going to have enough connectors for a substantial number of drives. That's hardly important, though. 4:1 or 5:1 splitters are cheap and easy to come by. (That one is $6.69 right now.)

Also, one of the advantages of using a chassis with a backplane is that it saves you dealing with an enormous wiring harness.

You may, however, eventually run into other limitations of your power supply. (This is unlikely with 15 drives and a 650W PSU, however.) For example, how many rails does your power supply have, and what are their individual maximum wattages? (3.5" hard drives primary draw from the 12V rails.) There may be less than the full 650W available to your hard drives.

You will also see large current spikes at boot, when all of the drives try to spin up at the same time. The machine may fail to boot if this draw exceeds the power supply's capacity (again, either on those particular rails or overall). This can be mitigated by using staggered spin-up, which requires either controller/OS support or MacGyvering. (One of the pins in the SATA connector tells the drive not to spin up immediately when power is applied.)

All of that having been said, though, unless you have other complaints about your PSU, a few cables is probably the right fix.

If you're dead set on replacing it, then you should be most interested in power supplies with high efficiency at the load that you expect. (Do some math but also take some measurements, and then look at the PSU's datasheet. The single efficiency number that will be advertised on the product's website or box assumes that it is almost fully loaded.) Power supplies are also differentiated by features like active PFC (power factor correction).

If you're looking for a specific suggestion, I've had good luck with the EarthWatts series.

Good luck!

u/slowro · 1 pointr/buildapc

I more or less found what I was looking for. Helps when you know it is called sata power and not hard drive power cable.

But safe or not? Sorry if mobile link, on phone

https://www.amazon.com/dp/B0086OGN9E/ref=cm_sw_r_awd_ok0.ub17EJJZX

u/gd2246 · 1 pointr/DataHoarder

Ok then. But it's pretty easy and I've never screwed that up either. You could also just use a Molex to SATA adapter, works just as well. Or a SATA power splitter and cut the 3.3v wire.

u/Buck9999 · 1 pointr/homelab

I have two or three of these. I've had one for a couple years and the others just over a year. Haven't had any problems with them and them seem solid.

I'm powering 5 old Hitachi 2TB drives and 3 WD 8TB reds.

StarTech 4X SATA Power Splitter Adapter Cable https://smile.amazon.com/dp/B0086OGN9E/ref=cm_sw_r_cp_apa_i_Al9OCbBR56GD1

u/xanylea · 1 pointr/techsupportgore

If you have at least some sata power, you can get 1sata-to-4sata power splitters like this: https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E/

Due to how they have to be made (crimped, not molded) they should be fine.

u/RaulNorry · 1 pointr/buildapc

I've actually been using two of these (https://www.amazon.ca/StarTech-com-PYO4SATA-Power-Splitter-Adapter/dp/B0086OGN9E/ref=sr_1_2?s=electronics&ie=UTF8&qid=1505935424&sr=1-2&keywords=sata+to+sata+splitter) for the past two years in my NAS. I've got 9 hard drives and 2 SSDs powered from a 450W PSU, and haven't had a single issue at all with connectors feeling hot, PSU shutting down, etc. This is over an extended period, with drives being accessed concurrently at maximum speeds.

u/PARisboring · 1 pointr/buildapc

It's alright to use sata power splitters, but the type you linked are known to literally melt and burn. Don't get the type where the cables are molded into the connector. You can identify them by the cable running straight into the connector, rather than at a right angle. You want a splitter that uses sata connectors with crimp on taps. Those are solid. Like This.

u/toomanytoons · 1 pointr/techsupport

If you already have a standard SATA cable plugged into a hard drive, unplug it and use a splitter like this 4x power splitter. Try some google searches for the model # and the port # (r11) and maybe throw in "hdd/odd" for good measure. You could also call your manufacturer (Dell?) and ask them.

u/Grus · 1 pointr/DataHoarder

Cables like these that give you 4 SATA power connectors out of one molex connector, I've seen one with 6x SATA before, but I can't find it anymore, I hope I will. And then just a PSU with enough molex connectors, I guess. I think there might be some aftermarket cables for modular PSUs too, I don't know, it would make sense... But you could probably use more than one PSU to power all the drives, maybe that's a good idea anyway.

u/devilsdeeds · 1 pointr/homedefense
u/mmm_dat_data · 1 pointr/DataHoarder

wow, thanks duly noted. I been using these: https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E/ref=sr_1_3?s=electronics&ie=UTF8&qid=1482938279&sr=1-3&keywords=sata+power+splitter

how nervous would you be with sata power splitters? startech's not too bad a brand right? ....RIGHT? haha

u/coolhwip12 · 1 pointr/buildapc

Awesome, thank you for the detailed response.

So if I'm doing my math correctly, one SATA cable from the PSU would have four connectors. Splitting it with the 4x SATA splitter would put me at 7 connectors total. Let's say I run a high estimate of 9W per HD, that's still only 63W which is well under the 192W calculation. I was thinking about running a blu-ray drive on the same line which would still only be (9W6)+30W=84W total. So I would be safe in my instance is that right?

The AMP connector route you mentioned would still be well under since the molex to 4x SATA would be the only thing connected to that cable. 9W
4=36W or (9W*3)+30W (BD drive)=57W.

Would you recommend one route over the other (SATA to 4x SATA vs molex to 4x SATA)? Looking at either one of these guys..

https://smile.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E/

https://smile.amazon.com/Monoprice-108794-24-Inch-15-Pin-Female/dp/B009GULFJ0/

Thanks!

u/fastrthnu · 1 pointr/DataHoarder

Just buy some cheap Y splitters. We use them all the time.

StarTech.com 6in SATA Power Y Splitter Cable Adapter - M/F - Power splitter - SATA power (M) to SATA power (F) - 6 in - PYO2SATA https://www.amazon.com/dp/B002N2EHVQ/ref=cm_sw_r_cp_apa_i_d1hXDbBGRA2YX

Ooh even cooler 1 to 4!

StarTech.com 4X SATA Power Splitter Adapter Cable (PYO4SATA) https://www.amazon.com/dp/B0086OGN9E/ref=cm_sw_r_cp_apa_i_J3hXDb01TS76J

u/ZeroBANG · 1 pointr/pcmasterrace

What do you think about those here?

u/Switchen · 1 pointr/buildapc

One of these guys would split the SATA power for you.

u/finglongerUK · 1 pointr/techsupport

are you looking for something like this 4x sata

or molex to sata

if your looking for something that connects direct to the PSU then youd need to let us know make and model of the PSU but usually the best place to start looking would be on the PSU manufacturers website

edit: if your PSU only has one or two SATA\molex connectors this will usually indicate the PSU is very low voltage adding more drives than the PSU can supply with the cables provided could cause stability issues

u/yellowkat2016 · 1 pointr/DataHoarder

That's what I was initially thinking of. But I read some comments of people that had problems with that kind of solution messing up their drives. Maybe it was in the past and things have gotten better? Maybe due to the quality of components? I didn't wanna risk it. Plus, it's almost the same cost as a SATA 3 card.

https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E/ref=sr_1_3?ie=UTF8&qid=1537284746&sr=8-3&keywords=sata+splitter+power+cable

That's the most recent thing I found on Amazon that seemed like it could work for cheap. To just disconnect the whole extension instead of the drives themselves. Read they were safe too.

u/MrKazador · 1 pointr/DataHoarder

Molded sata power connecters are no good. You want a cable like this https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E/

u/knulltobak · 1 pointr/PleX

The adapter cable only splits the power from the PSU. All the HDDs got their own sata cable to the motherboard so they all show up as induvidual disks. They look like this.

u/ismee · 1 pointr/DataHoarder

Thank you so much for the response and info!

I saw this review on Amazon. What do you think?

That person also links to the following products. How essential/necessary do you think they would be to the node-804? I've read some other review that don't highlight suggestions as the review above does. What are your thoughts?

u/mithikx · 1 pointr/CableManagement

Hmm, I use something like this on a Corsair 750D but the cables on mine have smaller spaces than the product page on Amazon so they're a better fit for drive caddies. (the one I used I got from a local computer store)


Could you use this which comes in a 2 pack: https://www.amazon.com/Cable-Matters-Pack-Power-Splitter/dp/B012BPLW08/

u/arkhira · 1 pointr/pcmasterrace

This sounds like a Dell/HP/Acer prebuilt system. If so just get a 1TB SSD and clone your mechanical hdd over to the new SSD. I would advise against using molex -> sata power. If that is not an option then you could try something like this instead: https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E.

u/Spys0ldier · 1 pointr/burstcoin

Ah ok. For some reason I was thinking you had a modular psu but forgot a store bought pc prob wouldn’t. You can always get more sata power splitter. My psu is modular but I’ve already run out of power options and need to get a splitter like this StarTech.com 4x SATA Power Splitter Adapter Cable (PYO4SATA) https://www.amazon.com/dp/B0086OGN9E/ref=cm_sw_r_cp_api_MmJLAbVG5R700.

u/wchill · 1 pointr/DataHoarder

I bought a SATA power splitter (https://www.amazon.com/StarTech-com-Power-Splitter-Adapter-PYO4SATA/dp/B0086OGN9E) and then just cut the wire on the side with the L shaped bit. It's honestly easier to just do that (scissors to cut the wire + some tape to insulate) and it's only 7 bucks.

u/R3v7no · 1 pointr/buildapc

You can either A) build a cheap server for ~400 or B) use a sata splitter like this

u/nudelete · 1 pointr/Nudelete

>-Previous threads here-
>

>
>Objective:
>Going back to the original - The $500 build from /u/JDM_WAAAT. Since then, many of those parts prices have drastically increased in price or are unavailable. So new objective, build it better, for less! And oh man did we ever.
>
>
>Rules for buying used server-grade parts on eBay:
>
>1. Buy from highly-rated, reputable sellers
>2. When "Or best offer" is available, use it. Sellers will likely discount parts, often up to 30%.
>3. Shop around. There are many resellers selling the same exact parts on eBay, find the one with the best price.
>4. Scrutinize the details of the auction. For example, make sure CPU stepping / revision is correct to what you need. Make sure components are listed as functioning and not "for parts only".
>5. Do not, under any circumstances buy QA/QC/QS/ES labled CPUs. Only buy official used / refurbished Intel Xeon CPUs. Chips with this label are not guaranteed to work, and might break functionality with something as simple as a BIOS update.
>6. Check sources other than Ebay. /r/buildapcsales can be a huge help with this. Amazon or Newegg often have huge sales on some of the new parts. Shop around people!
>
>Build
>
>http://i.imgur.com/X1NzK7Z.png
>
>http://i.imgur.com/r2d3lQp.png
>
>http://i.imgur.com/AHQJmto.png
>
>Type|Item|Price (eBay) | OBO? | OBO price
>:----|:----|:----|:---- |:----
>CPU | 2x Intel Xeon E5-2650 2.00GHz, 8 core 16 thread | Incl w/ MOBO | |
>Motherboard | Supermicro X9DRi-LN4F+ Dual Socket | $281.98 | YES | $260
>RAM | 16GB (4X4GB) DDR3 ECC REG x 2 | $29.89 ea | YES | $25.00 ea
>CPU Cooler | 2x Arctic Freezer i11 CO | $19.22 ea | |
>PSU | EVGA 450W BT | $24.99 | |
>EPS Splitter | 8 Pin to Dual 8 Pin EPS Splitter | $6.00 | |
>24 Pin Extention | 12" 24 Pin Power Extention | $9.99 | |
>Case | Phanteks Enthoo Pro | $79.99 | $15 MIR | $64.99
>Thermal Compound | Gelid GC Extreme | $12.99 | |
>Other | Tax, shipping, fees | $3.60 | |
>Total | | $517.76 | after OBO | $471
>Optional Extras | Sata cable 6 pack | $7.49 | |
>Optional Extras | Sata power splitter | $6.27| |
>
>---
>
>About this build:
>
>There you have it. If you recall, the original $500 build actually used this same CPU. BUT ONLY 1!. Here, we used 2, gave it more RAM, and all for over $50 less!
>
> General: I recently completed almost this exact build, same mobo, case, etc. Just ended up with different RAM config, and used dual E5-2630L CPU's that i got for a steal. This build will be using two Intel Xeon processors on Intel Socket 2011 motherboard with Quad-Channel DDR3-ECC RDIMM memory. It does not include specifications for SSD or HDD.
>
CPU: The Intel Xeon E5-2650 is a high power, 8 core, 16 thread CPU that came out Q1 2012. 2.0Ghz clock, 2.8 Ghz turbo. It has a counterpart, the E5-2600L series who are also 8 cores, but low power. If you don't need quite as much Passmark power, these are also a power saving option at a slightly lower price point. MSRP when it was released was around $1100.00 USD Each. Plex Transcoder has true multi-threaded support and will take advantage of all 32 threads. So while this CPU might not be clocked as fast as what most of you are used to, the sheer amount of cores/threads will more than make up for it. Dual E5-2650's will score 15000 on passmark. Another thing to consider is that since the CPU is so cheap, you won't have to worry about it when it comes time to upgrade in the future. You can replace it with any V1 or V2 E5-2600 series cpu's. Dual E5-2660 V2, 10 core 20 thread, 2.20GHz base / 3.00 Ghz turbo in the future for about +4000 extra passmark score.
> Motherboard: Supermicro X9DRi-LN4F (Link to Supermicro Product Spec Page) This motherboard has dual 2011 sockets with a whopping 24 DIMM slots. With this build we'll be using only 8 of those available DIMMS, so there's a possible future upgrade. 6 SATA ports are standard, along with 2 SAS ports, for a total of 14 available SATA connections. Quad Gigabit NIC is also standard, plus IPMI.
>
RAM: Here, we're using 8x4GB DDR3 ECC REG for quad channel support, and a total of 32GB of available memory. 32GB is a good value here. Another 2 sets would fill all 24 slots, for a total of 96GB.
> CPU Cooler: There's not much to say here. It's compatible, it's quiet, and it works. We won't be overclocking, so there's not much to worry about so long as it works. Also designed for continuous operations.
>
PSU: It's cheap, powerful enough, and works. Not much more to say.
> Case: This case has full SSI-EEB+ (E-ATX with specialized mounting) support. Supports 6 3.5" hard drives two 2.5" SSDs, and two 5.25" bays natively. It's an all-around wonderful case, and it's really well-constructed (I have one, it's great). Also, one of the few cases that actually will fit this massive MOBO. In the front is a MASSIVE 200mm intake fan. Didn't even know they made them that big.
>
Splitter/Extension These are necessary with the parts listed above to work. The power supply listed only has 1 8 Pin EPS connection for the CPU. Since we have 2, need a splitter. If you use a different PSU, check on the # of EPS connections. If it has 2, this part is not necessary. This board BARELY fits in the case. I know, I have both! Here's some pictures to show. Because of this, wiring the power can be a bit tricky, and to get it done in a clean way, need the 12" extension.
>
Thermal Paste This is the best non-liquid metal thermal compound out there, hands down.
>
>Cautionary notes, other details
>
>1. Server equipment is stripped down to the bare minimum for compatibility and reliability. Because of this, features you are used to having might be missing - for example, some server motherboards don't have onboard audio. Also, most will use VGA onboard.
>2. Use a SSD for your host OS. This is likely where your Plex metadata will live, so if you're going to generate thumbnails and you have a sizeable library, make sure to get an appropriate size. I have about 20TB of media with thumbnails turned on, and 500GB is starting to feel tight. About 250GB is a good start for most people.
>3. Familiarize yourself with the BIOS options. Some may be different than consumer models. Make sure Hyper-threading is turned on in the BIOS. When in doubt, clear the CMOS / reset to default. You should verify that all 24-threads are showing in your host OS.
>4. Almost any OS will work. Includes ESXI, unRAID, FreeNAS, Linux, and Windows of course.
>5. Evaluate your RAID options. This motherboard has capabilities for onboard RAID, but that isn't for everyone.
>
>Upgrades, other parts
>
>1. Cheap storage in the form of $33 refurbished 2TB Hitachi Ultrastar hard drives. These are Enterprise level drives, great for use with RAID arrays.
>2. Sell the pair of E5-2650's & get Dual E5-2660 V2, 10 core 20 thread, 2.20GHz base / 3.00 Ghz turbo for 19,000 Passmark score. At time of posting these were $249.99 OBO w/ free shipping, extremely great value currently. If you're more concerned about power consumption, consider a pair of E5-2650L's for $41.50 each OBO at the time of this post, for a sweet ~14k passmark at only 70w TDP each.
>3. MORE RAM!
>4. Liquid cooling - If you plan on upgrading to V2's this is a good idea. Can get Corsair H55's for $60 each.
>5. DO IT ALL! If you want more power right now, sell the CPU's that come with the mobo for ~80 and grab a pair of E5-2660's for $240. Triple the RAM for an extra $100. Liquid cool the PSU's for an added $80. Finally, upgrade to a 550w semi modular 80+ gold psu for an extra ~$30 (one's on sale @ Newegg for $55 after MIR currently). Grand Total: around $840.
>
>FAQ
>
> Q: Aren't used parts unreliable?*

u/remembertosmilebot · 0 pointsr/techsupport

Did you know Amazon will donate a portion of every purchase if you shop by going to smile.amazon.com instead? Over $50,000,000 has been raised for charity - all you need to do is change the URL!

Here are your smile-ified links:

this 4x power splitter

---

^^i'm ^^a ^^friendly bot