Reddit Reddit reviews Stelpro Z-Wave Plus KI STZW402WB+ Thermostat (White) for Electric Baseboards and Convectors

We found 15 Reddit comments about Stelpro Z-Wave Plus KI STZW402WB+ Thermostat (White) for Electric Baseboards and Convectors. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
HVAC
Household Thermostats
Building Supplies
Home Thermostats & Accessories
Home Programmable Thermostats
Stelpro Z-Wave Plus KI STZW402WB+ Thermostat (White) for Electric Baseboards and Convectors
UNIQUE Z-WAVE: The Stelpro KI is the first Z-Wave thermostat in North America to work with line voltage, with a 2-wire connection to the heater.EFFICIENT HEATING: Remotely control your baseboard and convector heaters from your mobile device or computer (when included to a Z-Wave gateway controller - sold separately).SAVE SMART: Set your own temperature schedules to reduce energy bills with minimal effort; take advantage of the device's ECO mode, designed to be as energy-efficient as possible.ELEVATED CLIMATE CONTROL: Create advanced automations by pairing the Stelpro KI with other Z-Wave devices. Trigger the heating on/off with a door/window sensor, temperature sensor, motion sensor, etc.CERTIFIED QUALITY: This thermostat is Z-Wave Plus and UL certified. Made in Canada. Works with SmartThings, Vera, HomeSeer, Nexia and Wink.
Check price on Amazon

15 Reddit comments about Stelpro Z-Wave Plus KI STZW402WB+ Thermostat (White) for Electric Baseboards and Convectors:

u/Anydudewilltellyou · 8 pointsr/HomeImprovement

/u/tainttrauma, read his post again. He has electric baseboards. Those have line voltage thermostats. You've recommended low voltage units.

Yea, that's not gonna' work for him.

There aren't a whole lot of options for smart line voltage units. Especially if the baseboards have a fan incorporated into them.

This one MIGHT work. Need to see if it is compatible with O.P.'s units:

https://www.amazon.com/STZW402WB-Thermostat-Electric-Baseboards-Convectors/dp/B01BYL1OAS

u/jryanishere · 5 pointsr/homeautomation

I have electric baseboard heat in my basement.

This is what I use to control it.

It works great.

Beat's the hell out of my old setup of a transformer, relay, and standard stat.

Pick a controller of your choice to control them all. Home Assistant on a Pi would be the cheapest local solution to get going.

u/ajc253 · 4 pointsr/homeautomation

I just ordered a couple of these.

Stelpro Z-Wave Plus KI STZW402WB+ Thermostat (White) for Electric Baseboards and Convectors

https://www.amazon.com/dp/B01BYL1OAS/ref=cm_sw_r_cp_api_yap9BbV3PDQET

u/baudfather · 2 pointsr/homeautomation

Depends what kind of hub you have. If you don't have z-wave, you're options are pretty limited. Easiest and safest IMO would be a zwave baseboard thermostat. Something like this, depending on size of heaters, etc: https://www.amazon.com/Stelpro-STZW402WB-Electric-Heater-Thermostats/dp/B01BYL1OAS

​

u/computerguy0-0 · 2 pointsr/homeautomation

For electric baseboards: https://www.amazon.com/Stelpro-STZW402WB-Thermostat-Baseboards-Convectors/dp/B01BYL1OAS

For the main oil heating zones, I would honestly do a few more z-wave thermostats then pull it all together with your home automation software of choice (Home Assistant, HomeSeer, Smart Things, Wink, etc...)

Depending on what was used for floor heating, you may not be able to do much with this besides wire something for on/off.

u/byobeer · 2 pointsr/HomeImprovement

Chance are that those baseboard thermostats are 'line voltage' units. Either 115v or 230v AC. Which means that they control the units by turning the power to them on and off.

Conventional (smart) thermostats are low voltage. They operate on 24v AC. They tell relays to operate the system. You cannot use a low voltage unit on a line voltage device. Well, you can, for about 2 seconds. Then you let the smoke out of your new thermostat.

I have seen a StelPro unit, which is designed for your application. You might want to check it out:

https://www.amazon.com/STZW402WB-Thermostat-Electric-Baseboards-Convectors/dp/B01BYL1OAS

u/dsinton · 1 pointr/homeautomation

Maybe this Stelpro KI STZW402WB+ Thermostat for Electric Baseboards and Convectors https://www.amazon.com/dp/B01BYL1OAS/ref=cm_sw_r_cp_api_i_XBr6AbR8BCPXT

u/chabz5000 · 1 pointr/amazonecho

i have electric baseboard and use a stelpro KI z-wave thermostat for control.

you'd need a z-wave hub to bridge the two systems (i use smartthings), and with this unit alexa doesn't have native thermostat control -- i had to install the alexa helper apps for smartthings.

right now i have an 'off' temperature setpoint and an 'on' temperature setpoint, so i just have to say 'Alexa, turn the heat on' or 'Alexa turn the heat off' to switch setpoints respectively. i can also say 'Alexa turn the heat up' and it bumps the setpoint by 5 or 10 degrees (i forget which, and i'm not home to check). asking alexa to turn the heat down just turns it off (with my setup anyway).

u/jam905 · 1 pointr/ecobee

Electric baseboard units typically have line-voltage thermostats, which the ecobee3 (or ecobee3lite) is not. So you need a different solution if you want to make them "smart", such as the Stelpro KI STZW402WB+, along with a z-wave controller.

For your radiator, you can use either the ecobee or the ecobee3 lite depending on how uniformly the radiators heat your downstairs. If there are hot/cold spots, then the ecobee3's sensors may be useful.

u/Monkey_Tennis · 1 pointr/homeautomation

I'm looking to do this too, and it looks like the Stelpro KI STZW402WB+ is the way to go as /u/jryanishere mentioned.

It's worth noting, that hooking a Nest up via a relay is NOT supported. Nest have taken down their community forum that had a good guide on how to do it. There are others on the web, but I'd steer clear.

u/ArizonaLad · 1 pointr/HomeImprovement

You need to cut the power, and open it up. There are two ways your baseboard heat could be wired:

Two hots (black and red wires, no neutral, and a ground). The line voltage thermostat controls both wires. Or, the thermostat controls one wire only. This is old school, and while it works, you still have one leg that is carrying voltage. But since you don't have a completed circuit, it doesn't get hot.

Hopefully the new wall heaters will have their own t-stat built into them. There are currently very few choices for modern smart 'stats that will work in your situation:

https://www.amazon.com/STZW402WB-Thermostat-Electric-Baseboards-Convectors/dp/B01BYL1OAS

A Bluetooth only version:

http://www.morelectricheating.com/default.aspx?page=item+detail&itemcode=KINGELECTRIC10395&catlist=2299&parent=9629

A wifi version, to connect to your home network:

http://www.morelectricheating.com/default.aspx?page=item+detail&itemcode=KINGELECTRIC10397&catlist=2299&parent=9629

u/sidoh · 1 pointr/homeautomation

https://www.amazon.com/STZW402WB-Thermostat-Electric-Baseboards-Convectors/dp/B01BYL1OAS

This is for line voltage thermostats. Not sure if yours fits that bill

u/Notevenspecial · 1 pointr/HomeImprovement
u/RandomUser0137 · 1 pointr/homeautomation

https://www.amazon.ca/Stelpro-STZW402WB-Electronic-Thermostats-Smart/dp/B01BYL1OAS/

I use these z-wave thermostat's for my electric baseboards...I quite like them as they are easy to set up and configure. I use a pi running HA and a z-stick.

Now if I can only figure out how to get the "outside temperature" feature to work with a virtual temperature sensor....

u/arizona-lad · 1 pointr/HomeImprovement

The statement about no smart thermostats for baseboard heating is not entirely accurate. Look at the StelPro:

https://www.amazon.com/Stelpro-STZW402WB-Thermostat-Baseboards-Convectors/dp/B01BYL1OAS