Reddit Reddit reviews Swanson Tool S0101 7-inch Speed Square Layout Tool with Blue Book

We found 14 Reddit comments about Swanson Tool S0101 7-inch Speed Square Layout Tool with Blue Book. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Measuring & Layout
Carpentry Squares
Swanson Tool S0101 7-inch Speed Square Layout Tool with Blue Book
The Speed Square, made in the USA since 1925, is essential for every carpenter, construction professional, roofer, and DIYerSpeed Square belongs on every tradesman's tool bench; includes Try Square, Miter Square, saw guide, line scriber, and protractorIncludes pocket-sized Swanson Blue Book, a comprehensive guide to help workers make correct angle cuts for any pitched roofFeatures: 1/4-in spaced scribing notches and the Diamond cutout for easy rafter seat cuts and scribing the most common and popular stud widthsGradations included for marking common, hip, valley, and jack rafters; Useful for determining and marking angles and making square cuts on boards
Check price on Amazon

14 Reddit comments about Swanson Tool S0101 7-inch Speed Square Layout Tool with Blue Book:

u/soonerborn23 · 18 pointsr/HomeImprovement

depends on what diy goals you have in mind. What I find myself using 80+% of the time when I am doing home diy stuff is some combo of the following.....

u/ReverendSaintJay · 6 pointsr/DIY

I didn't see one of these in your pictures, but it would have made the circular saw cuts a whole lot easier.

http://www.amazon.com/Swanson-SO101-7-inch-Speed-Square/dp/B00002255O

The overhang on the back allows you to work with a circ-saw really well and get 90 degree cuts every time. For your table you could have offset it just enough to put your level between the speed square and the saw to use it as a longer guide.

u/coherent-rambling · 5 pointsr/BeginnerWoodWorking

Here's what I would buy if I were equipping my garage workshop on a budget from scratch today:

  • Table Saw - Unless you go for hand tools, this is the absolute core of your shop. Do not buy a new saw for less money than this under any circumstances, because it's false economy and you'll soon outgrow it. You may wish to buy a cheaper used model, in which case you should shop for a Craftsman 113 (aim for a belt drive rather than direct drive) on Craigslist. Spend up to $150 and plan to build or buy a better fence in the first year, which will bring you up to roughly the same capability as the new saws.
  • Drill and Driver - You need a drill anyway. Everyone does. This is nothing fancy, but it's a tolerable set that should last a hobbyist quite a while, and both batteries and extra tools are cheap. Grab a set of drill bits and a few impact-rated screwdriver bits, or a fancy combo set of both.
  • Miter Saw - Indispensable for cutting long pieces. You may eventually wish to get a big 12" sliding monstrosity to make wider pieces easier to work with, but you can also do that with a table saw. I suggest an inexpensive variant of the most basic type of miter saw to start, so you've got a good foundation to work from but don't have a ton of sunk cost if you upgrade later.
  • Circular Saw - You'll use this for breaking down sheets of plywood bigger than your table saw can handle. You can also use it as a stand-in for the table saw for the first few projects. I'm recommending a lightweight cordless model for convenience during these simple, short tasks, but if you work with thick materials you may eventually want a powerful corded one as well - I've got a cordless and then a monstrous 15-lb worm drive saw for heavy duty use. If you just want to split the difference right off the bat and have one tool that's okay for everything and not great at anything, get a basic corded one.
  • Jigsaw - For cutting curves and small notches. Make sure you get one with orbital motion, but other than that you can go pretty cheap on this because you won't use it that often. However, buy top-of-the-line blades; I really like Bosch blades.
  • Router - This is a very capable middle-of-the-road router. You'll eventually want to add a plunge base, and might add a lightweight trim router to make edge profiles more easily. You can get accessories to expand on this, or you can eventually dedicate it to a router table and buy new for those other things - the variable speed motor on this is ideal for table use.
  • Sander - This is the most general-purpose sort of sander, although it's a little on the aggressive side for final sanding. Just hand-sand where you need more finesse until you know what other sanders you might want.
  • Combination Square - Use this for laying out cuts and holes and stuff.
  • Speed Square - That blue book will show you tons of neat tricks with this square. Mostly you're going to use it as a short guide for the circular saw, though.
  • Tape Measure

    Edit: Looks like that's about $1,100.00 depending on your local tax rate and how much of it you can slip past untaxed. That's steeper than I expected, but it's also an entire barebones shop for less money than the table saw I really want.
u/lying_Iiar · 3 pointsr/woodworking

If the bandsaw runs, it should still be useful. You can purchase a new blade if there's an issue with the existing one. The chisels will be fine, but you'll have to learn how to sharpen them. Sharpening systems can be expensive, though.

Otherwise it depends a little on what you want to build.

If I were starting out on a significant budget, I think I'd go with a skil saw, triangle square, tape measure, and drill/driver set. And I'd be thrilled to have a bandsaw & chisels. If you can, buy a good skil saw. Don't too much worry about the quality of the rest.

Those will all be very useful later, too, of course. Might build some sawhorses first and go from there.

A skil saw is really useful for breaking down pallets, as well, in case you plan on making use of them as a source of lumber while you're starting out.

If you want a more specific list, I own these products:

https://www.amazon.com/Stanley-33-312-Powerlock-Tape-Rule/dp/B00002X2GN/ref=sr_1_5?ie=UTF8&qid=1497387060&sr=8-5&keywords=stanley+tape+measure

You don't need a 25' tape and a 12' tape is easier to use.

https://www.amazon.com/5280-01-15-Amp-4-Inch-Circular-Single/dp/B01BD81BLO/ref=sr_1_3?ie=UTF8&qid=1497387078&sr=8-3&keywords=skil+saw

That skil saw isn't the best in the world, but it'll get you pretty far.

https://www.amazon.com/Swanson-S0101-7-inch-Square-Layout/dp/B00002255O/ref=sr_1_1?ie=UTF8&qid=1497387123&sr=8-1&keywords=triangle+square

Just a cheap, basic square.

You'll also want some clamps, no doubt. On a tight budget I'd get some walmart cheapies. They're not great, but they get the job done, and clamps are crazy expensive. You want them to be basically like this:

https://www.amazon.com/IRWINQUICK-GRIPOne-Handed-Mini-Bar-Clamp-1964742/dp/B00002244S/ref=sr_1_1?ie=UTF8&qid=1497387348&sr=8-1&keywords=woodworking+clamps+hand

But larger (12-36"). And walmart brand is cheaper, I think they're about $3 for a 12" clamp.

Good luck! Ask questions!

If your goals are to do fine woodworking, like interior furniture (that isn't "rustic")...or if your budget is much larger, then you'll be looking at an entirely different set of tools.

Table saw, planer, orbital sander, bandsaw (if yours is no good), bench grinder, miter saw, jointer, in order of importance (to me!). And lots and lots of hand tools. Marking gauge, marking knife, awl, variety of drill bits, counter sinks.

Belt sander, disc sander, jigsaw, router. Router can be way up there in importance if you make good use of it--very versatile tool. I just don't use it a ton personally, and bits can be very expensive.

u/EntireOrchid · 3 pointsr/HomeImprovement

Speed square + clamp of your choice + cordless saw with metal-cutting blade.

Or use a speed square to mark your cut with a pen and then freehand cut with an angle grinder. Following a line is a lot easier than just winging it.

u/anotherisanother · 2 pointsr/woodworking

For true minimum you can use a hand saw, a drill, and something to support the wood, like some buckets or a pair of saw horses.

For angles, use a speed square or sliding bevel and kids protractor.

u/Vlacik · 2 pointsr/DIY

The entire project can be done with these tools:

u/thesirenlady · 2 pointsr/Machinists

its fine, though a bit small for what you want. good to have for general workshop purposes though

For squaring a rest and platen, or a 123 block.

u/RugerRedhawk · 2 pointsr/DIY

You would use this to draw your line: http://www.amazon.com/Swanson-Tool-SO101-7-inch-Square/dp/B00002255O/ref=sr_1_1?ie=UTF8&qid=1376580412&sr=8-1&keywords=speed+square

Of course you can do any job many ways, but a miter saw is going to come in handy and be a lot quicker and more accurate than using a circular saw. Definitely buy the circular saw first though, because as you say it can do the work of a miter saw plus more.

u/MattyH · 2 pointsr/HomeImprovement

I've built 2 sets of very similar shelvles. My notes:

Make the shelves 8' between the uprights so you don't have to cut out the notches. (or cut the length to whatever the "between" length is).

You need some joists running from front to back to keep the OSB from sagging. Every 2 feet would be fine, but go every 16" for a super super sturdy shelf that can hold really heavy stuff without sagging.

I'd use 1/2" plywood instead of the OSB, though the OSB would work fine (but only with the joists). Plywood is stronger and more stable over time. May not be an issue.

Circ saw is the tool for the job. And a speed square

The other tool for the job is a cordless screw gun/drill to drive the screws. Corded would work too, just not nearly as easy. Use deck screws and no predrilling required.

If you're wanting some new tools, I highly recommend Ryobi's lithium-ion cordless stuff that is common in hardware stores these days. The little cordless circ saw and drill could knock this out easily. I've ripped plenty of plywood with the circ saw, surprising myself how well it works.

Regardless of brand, if you're getting a circ saw, get one that shoots a laser out of the front on the cutting line. Allows you to cut quite straight lines freehanding it.

Have fun!

u/cheesuschrists · 1 pointr/HelpMeFind
u/RenegadeX21 · 0 pointsr/cade

You might benefit from using one of these.

The right side of the bezel looks like it is cutting off part of the screen (vis: barrels).
That said, it looks great! Love the metal accents. T-molding & Paint will really make it look great.

Consider making something to fill in the gap on the top. As others have mentioned, a marquee might/speakers (speaking of, where is sound coming from, now?) would be a good choice.