Reddit Reddit reviews TEKTON 3179 35mm Double-Face Soft Mallet [Older Model]

We found 3 Reddit comments about TEKTON 3179 35mm Double-Face Soft Mallet [Older Model]. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Hand Tools
Hammers
Mallets
Power & Hand Tools
TEKTON 3179 35mm Double-Face Soft Mallet [Older Model]
Two 35mm Diameter Replaceable HeadsBlack Rubber Head for a Cushioned Strike, High Impact Plastic Head For a Positive StrikeRugged Tubular Steel HandleCushioned Non-Slip Rubber Handle GripQuality Guarantee
Check price on Amazon

3 Reddit comments about TEKTON 3179 35mm Double-Face Soft Mallet [Older Model]:

u/give_me_candy · 14 pointsr/DIY

I just posted another comment so you'd see a notification.


Here's the list! Hope it's not too long. All the tools listed are the ones I bought. If I have other suggestions, I've listed them as well. I've also listed details on the functions of the tools, and why they're superior to some other alternatives. If you look for the same amount of tools in one of those "kits," they would set you back roughly 200-400, depending on where you bought it from. The tools in these kits are usually quite inferiorly made as well. This list is a result of about a week long search and perusal. Tandy is a well known and easily accessible aggregation of tools, but they're overpriced for what they do and their quality is mediocre at best.

  • Stitching Chisel Set Amazon - $19 - Used for even stitching holes. An alternative to this tool would be something called an overstitch wheel, but from what I've read, the consensus seems to be that pricking irons are better and more reliable for straight lines. Also, overstitch wheels don't pierce the leather all the way, and only mark the holes, meaning that you have to pierce each hole individually with an awl after you're done. Double the work.

  • Stitching Groover & Edge Trimmer Amazon - $22 - This tool combines three tools into one. The edge groover, edge trimmer, and fold liner. It's not amazing quality admittedly, but it gets the job done well, and for the price I really can't complain. The edge groover cuts out a thin channel which sets the thread in deeper in the leather. Edge trimmer smooths the sharp corners, and the fold liner makes a line if you want to fold the leather somewhere.

  • Cutting Mat Amazon - $10 - I'd say absolutely necessary for anything leather related. This one is really cheap, works great. I have the 18x12 inch model, and the price is for that one as well.

  • Hole Punch Set Amazon - $9 - I'd say this one is more on the optional side. Mostly needed if you're interested in putting in hardware like rivets or snaps. Also good however for oblong rounded holes, like I showed in my project.

  • Mallet Amazon - $8 - Needed for all sorts of things. A normal metal hammer won't work because it won't absorb any force at all and all energy will be transferred to the leather, potentially damaging it. A rubber mallet allows for a softer hit.


  • Diamond Stitching Awl Ebay - $9 - While technically not necessary if you're using a stitching chisel, if the leather you're working with is extremely thick, it might help to have it. You should get one anyway though. You'll inevitable end up using it. Also, make sure to get a "Diamond" pointed one. Normal awls with round points just poke a hole in that doesn't close back up. Diamond points are wide and thin, and this allows the leather to close back up on the thread after it has been sewed up. C.S. Osborne is also American made.

  • Skiving Knife Ebay - $9 - Needed for thinning leather when folding, or simply trimming thick leather. There are several different styles, and they all definitely require a bit of finesse to be used properly, but are immensely rewarding once learned. Also a C.S. Osborne.

  • Bone Folder Ebay - $7 - One of the tools you can improvise for. It's needed to crease corners when folding to flatten them out. Also can be used to burnish. The cocobolo burnisher that I made ended up working just as well as this for folding as well. Any smooth, rounded/flat long object will work well for this. This one is also a C.S. Osborne.

  • Harness Needles Ebay - $7 - Size 2 is what I got, and it fits with 0.8 thread, also what I used. These needles are handy because the tips are somewhat rounded, which means no pricked fingers. Comes in a pack of 25, and the first two that I pulled out are still going strong, so they're quite sturdy.

  • Ritza "Tiger" Thread Ebay - $7 for 25m - Obviously endless varietes of alternatives here. However, in my research it seemed to be the consensus that this was the superior thread. It comes already waxed, and it's extremely durable. The 0.8mm size fits the size 2 needle, and both are great for small projects.

  • Barge Cement Ebay - $4 or $23 - Barge cement is a well known glue for leatherworkers, and works well. It's used to hold edges together to make sewing easier, as well as holding folds down. The thing is, they released a new formula, (the $4 one) that is "eco-friendly" and is missing some key chemicals. This is the one I got. It also kinda sucks at holding leather together. The original formula, (the $23 one), comes in a quart size at the smallest, but from what I heard this one is rock solid and the origin of their reputation. If you're planning on doing many projects I'd just say to invest in the quart.

  • Stitching Pony This is what it looks like - I didn't put a link to a product for this one because all the ones I have seen are ridiculously overpriced. I made my own out of some more scrap hardwood I had laying around, (you can barely see the tip of it in the sewing picture here and it works flawlessly. It's used to hold the leather together so you can saddle stitch it, which requires both hands. Besides the wood, it cost me about $3 in hardware to make my own. You can easily whip one up with some 2x4s and a long bolt, knob, and some screws, for a grand total of probably $5 from home depot. You may need a table or miter saw, or equivalent.

    *Some of the eBay listings might have ended, but I'm sure you'll be able to find identical tools for the equivalent price or even cheaper.

    For me the tools came out to a grand total of roughly
    $115. You can give or take $20 if you want to improvise your own tools, or switch them out. I'd say this setup works just fine for mid to smaller projects like what I made, or wallets, etc.

    As for the leather, Springfield Leather sells some quality leather by the square foot, which is nice for first timers, as most tanneries only sell by the side, like what I had, which usually average around 21-28 square feet. Pretty big investment. Maverick Leather Company sells quality leathers as well as Horween "Seconds", like what I got for a very nice discount. These seconds are full sides with minor defects in the leather, but unless you're making huge bags it's easy to cut around the brand marks/scars etc, and your leather will look spotless. I got a full side of Horween Essex for roughly
    $130, and I'm guessing if I bought the same straight for Horween it would have run me in the ballpark of $300 or so. Since my laptop case only used about 7-8% of my leather, I used about $10 worth of leather. Quite a bargain if you ask me. If you're looking to do many projects like I am, I'd advise you to invest in a nice Horween side. Can't beat it for value and price.

    All told, the laptop case itself cost about
    $11-12 worth of materials** (leather, fabric, thread, glue) and took the better part of 2 days to complete. Granted, much of that time was spent just sitting and thinking as most of it was improvisation, as you can see by my horrible sketch.

    As far as my "learning" went, it was literally just Google. Some youtube videos help, and I glanced through some forums, but overall, as I've often found in woodworking too, nothing beats hand-on experience.

    Well, hope this helped you guys out and answered some questions. I know I definitely would have appreciated a specialized list like this when I was starting out.
u/Roguewolfe · 2 pointsr/ar15

Looks good, sir. I did the same thing with a google doc for my 300BLK build.

I really like those sights, I have the exact same ones with the HK style front on my Windham SRC.

If you don't already have a hammer, you'll want to get a non-metal one to use with the punches. I got this one, good price and works well.

u/Jwast · 2 pointsr/ar15

Man I just finished this post and it's kind of long, oh well, that's what I get for staying up all night getting hopped up on diet soda like a rebel.

Start with buying a stripped lower, don't get hung up on brand names, there are only a handful of lower manufactures out there (I believe less than 10, maybe less than 5). Most companies have someone else make their lowers and stick their roll mark (the design on the side of the lower) on it then sell it at a 50% markup. This is the only part of the entire firearm that can not be shipped to your doorstep unless you have an FFL.

Next, since you don't want anything flashy, I would suggest the Palmetto State Armory Classic Lower Build Kit and bam, your lower is all done.

For your upper, I think I would stick to more reputable brands since there seem to be more manufacturers due to the lack of the involvement of headaches with the ATF, grab one with a lot of high reviews and then buy a PSA AR15 Upper Build Kit. For a barrel just go with whatever suits your taste, my preference is definitely 16" with a mid length gas system, it's a dream to shoot. I would recommend getting one with a front sight post already pinned on, if you decide you don't want it (like if you would want to install a free float hand guard), it's very easily replaced but if you get one without and decide you want it later it's probably the most involved/complicated thing you can even do with an ar-15. If you get a barrel with a pinned on front sight/gas block then grab the appropriate length hand guard for $20-$40 and then you need a muzzle device and a crush washer which should be about $8-$10. Buy some charging handle, everyone I know owns a Bravo Company gunfighter charging handle and loves it but I have heard a lot of good things about the Ranier Raptor charging handle as well.

Now, for a bolt carrier group, you do not want to assemble this at your kitchen table, at least not the carrier. The gas key staking is probably the most important part of the entire firearm in terms of reliability, I can't stress this enough, buy your bolt carrier from a reputable company, if you can get a Bravo Company bolt carrier group DO IT and don't look back. Once you get it, don't ever remove the gas key either, I wish I could find the video but I can't, it was of some youtube clowns running around with ar-15's and one of their rifles kept malfunctioning, he same something dumb like "I even removed the gas key and cleaned it out, I don't understand why it isn't cycling" later in the video he took out his bolt carrier and it was rattling like a paint can.

Also, factor tools in to your budget, probably around $50-100 depending on what you already have and how easily you want your build to go. The only thing you absolutely will need is an armorers wrench, everything else can be cheesed or is more for convenience. A torque wrench really should be used for the castle and barrel nuts, a center punch for staking the castle nut is actually cheaper than a tube of loctite, a small table clamp vice like this one should be sufficient if you don't have one already and a set of vice blocks will make your life easier when you torque stuff down, a set of roll pin punches and a non-marring hammer will keep everything nice and pretty but are not required if you take your time and go slow.