Reddit reviews TEKTON 5866 12-Inch Oil Filter Pliers
We found 13 Reddit comments about TEKTON 5866 12-Inch Oil Filter Pliers. Here are the top ones, ranked by their Reddit score.
Fits oil filters from 2-1/4 inches to 4-1/2 inches in diameterThree-position slip joint design quickly adjusts to sizeRight-angle teeth grip while turning in either directionLong handles reach into tight spacesSoft, comfortable grips offer nonslip control
I've used an oil filter wrench before, it works pretty well
Got any good size channel locks you can get on it?
I had to put a screwdriver in the side and eventually went all the way through one time then turned. (This was on my ‘99.)
I bought this one not long after.
TEKTON 5866 12-Inch Oil Filter Pliers https://www.amazon.com/dp/B000NPR33O/ref=cm_sw_r_sms_c_api_BJtMAb2G01VJ8
When you got a put one back on, just do it snug with anti-seize. Pretty hand tight is good. The heat will expand it and cause it to seize up.
Best $12 I ever spent.
https://www.amazon.com/dp/B000NPR33O/ref=cm_sw_r_taa_ZtsOybJ1G5QCR
I'd change the oil and filter again ASAP. It most likely won't blow up in a few hundred km, but it really should be done. What kind of filter wrench are you using? If it's really stuck I'd recommend getting the appropriate sized end cap wrench like these: https://www.harborfreight.com/End-Cap-Oil-Filter-Wrench-Set-4-Piece-63707.html
With one of those and a long ratchet or breaker bar you could probably remove a filter installed by The Hulk.
Edit: if you can't find the right size or you'd rather have an adjustable tool, you could also try this type of pliers: https://www.amazon.com/TEKTON-5866-12-Inch-Filter-Pliers/dp/B000NPR33O
I don't have this exact model, but I have one in this style. https://www.amazon.com/TEKTON-5866-12-Inch-Filter-Pliers/dp/B000NPR33O/ref=sr_1_3?ie=UTF8&qid=1501010937&sr=8-3&keywords=oil+filter+wrench
It is my "go to" if the filter is tight and I don't have a model specific tool.
http://www.amazon.com/gp/product/B000NPR33O/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1
I use a pair of these as my main set of oil filter pliers, and something similar to this if a filter really wants to start some drama. Something like this socket type strap wrench pretty much always works as well, is cheap, and is easier to fit than the strap wrenches with the big plastic handles built in.
This Filter wrench has taken off every filter I've ever had with no issue. might be worth a shot.
You can buy oil filter wrenches that look like this or this. Both work really well and most auto parts stores or Harbor Freight carry them. A large pair of channel locks work as well. The filter is already fucked, so don't be afraid to squeeze it into an oval shape to get a good bite on it.
The coolant line looks like a pre-heater for the intake manifold, where it runs coolant through the intake to make it heat up faster so that the engine can lean out (fuel injection doesn't have a choke, but does essentially the same thing when the engine is cold and that is richen the fuel mixture). Again, a foot or so of 3/8 or whatever size heater hose is only a few dollars at an auto parts store.
I've found these work better than anything I've ever tried.
TEKTON 5866 12-Inch Oil Filter Pliers https://www.amazon.com/dp/B000NPR33O/ref=cm_sw_r_awd_6OzAub010K5RS
I've used those, and they do work fairly well if you can get them to grip. It's a specialty tool though, and everyone has a screwdriver.
Mine has a 3/8 square hole in it and requires a short extension. I still grab the screwdriver when it's really stuck though, mostly out of habit.
These usually work fairly well too: http://www.amazon.com/TEKTON-5866-12-Inch-Filter-Pliers/dp/B000NPR33O/ref=pd_sxp_grid_pt_1_2
https://www.amazon.com/TEKTON-5866-12-Inch-Filter-Pliers/dp/B000NPR33O
These are what I use.
TEKTON 5866 12-Inch Oil Filter Pliers https://www.amazon.com/dp/B000NPR33O