Reddit reviews Tripp Lite Basic PDU, 30A, 20 Outlets (16 C13 & 4 C19), 200/208/240V, L6-30P Input, 15' Cord, 1U Rack-Mount Power, 5 Year Warranty (PDU1230)
We found 15 Reddit comments about Tripp Lite Basic PDU, 30A, 20 Outlets (16 C13 & 4 C19), 200/208/240V, L6-30P Input, 15' Cord, 1U Rack-Mount Power, 5 Year Warranty (PDU1230). Here are the top ones, ranked by their Reddit score.
Single phase PDU: safe, reliable power distribution unit delivers 200/208/240 volt single phase AC power to multiple loads from a utility outlet, generator or UPS system in a high density it environment. Ideal no frills basic PDU for networking, telecom, security, PDU networking, and audio/video applications20 outlet power distribution: The PDU features 20 total outlets rear C13, four front C13 and four front C19. The NEMA L6 30P input Plug with long 15 foot (4.5 meter) cord connects to your facility’s compatible AC power source, generator or protected ups to distribute power to connected equipment. Pdu offers 208/240 volts AC, 30 a maximum input currentSwitchless design: the switchless design prevents an accidental shutdown, which could lead to costly downtime. Built in circuit breakers protect connected equipment from dangerous overloads1U metal Housing: reversible all metal housing faces front or rear in rack. Power distribution unit mounts horizontally in 1U of EIA standard 19 inches 2 and 4 post racks, as well as on a wall or workbench or under a counter. Also known as PDU power strip, power distribution unit rack mount, basic rack PDU, PDU 30a, rack mount PDU and power distribution unit 19 rack mount5 year warranty & Free tech support: Tripp Lite warrants this product to be free from original defects in material and workmanship for the duration of the warranty. If the product should prove defective in that time, Tripp Lite will Gladly repair or replace it. Our chicago based tech Support team is ready to assist you with any warranty assistance, trouble shooting techniques or configuration help. Call them at 773 869 1234 M F 8am 6pm cst
Tell the electrician that you want 3 to 5 30-amp 240-volt breakers installed with one L6-30R receptacle running off of each breaker. Then buy these 240 volt PDU’s and some of these C13 power cords for your rig power supplies. You’re all set.
This 240 volt setup will double your capacity and make your power supplies more efficient.
I second this. I swapped everything over to 240 last night and everything seems much more stable. Definitely affordable, especially if you already have an unused 20/30A 240V in a garage or something and definitely worth doing. Tripplite 30A PDU ~$160 (https://www.amazon.com/gp/product/B0007YG85A/ref=oh_aui_detailpage_o04_s00?ie=UTF8&psc=1), C14 to PSU cables ($5 each or less if used) (https://www.amazon.com/gp/product/B000067RRX/ref=oh_aui_detailpage_o07_s01?ie=UTF8&psc=1), and presto. You're good to go. It was literally plug and play with all of my PSUs (EVGA, Corsair, Rosewill, etc.). Everything is on one 30A 240V outlet instead of spread across multiple 110 outlets.
If you're in the US, call an electrician. Tell him/her that you need a 240V (or 220V) 30A circuit installed that terminates into a L6-30R receptacle that you can plug one of these PDUs into:
https://www.amazon.com/gp/product/B0007YG85A (or similar spec PDU)
Also, buy a few of these 14/3 AWG C14-to-C13 power cables - one for each T9:
https://www.amazon.com/dp/B0085CE9O8
... and use them to connect your T9's PSUs to the PDU. 1 in each bank.
You can run 4 T9s off of the above 30A 240V PDU and circuit, while still observing the 80% rule.
That's it! Good luck.
UPS aren't relevant here. They are battery backups. You need a PDU. I use this one: https://www.amazon.com/gp/product/B0007YG85A/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
Make sure the plug matches. You will also need C14 to C13 power cords.
One 240/30A should be adequate :) That gives you 7,200 watts and even at 80% load that's 5,760 watt max so you're pretty close to that number. Go with two x2 240/30A for now; you may just need the one extra down the road if you expand or have a tool or something that can take advantage of the 240's. Might as well get it done while the electrician is in there.
We upgraded ours completely as our 100 amp panel to be upgraded so had my friend (master electrician) install new 200 amp panel (waiting for 200A drop by the electric company). 40-slot panel including whole house surge protector (fits inside two slots).
I took the possible maximum power each card can draw just to have some breathing room and ended up with x2 240/30A breaker running on L6-30 plugs with Tripp-Lite PDU's (https://www.amazon.com/gp/product/B0007YG85A) I split the power between the two lines even though I can probably run all my 40 1080 Ti's on one but wanted to spread the load a bit.
240's are nice since there's a slight increase in efficiency but also you're able to run server PSU's like HP's with breakout board which ends up being cheaper than buying couple 1200W PSU's.
I don't really know much about PDUs, so I just got a simple one. 30A 220v - which can run 4 of my 1400w server PSUs per PDU per 30A outlet.
https://www.amazon.com/gp/product/B0007YG85A/ref=oh_aui_detailpage_o07_s00?ie=UTF8&psc=1
I use this one, pretty decent. I can handle 3 to 4 antminers (depending on model). Tripp Lite Basic PDU, 30A, 20 Outlets (16 C13 & 4 C19), 200/208/240V, L6-30P Input, 15 ft. Cord, 1U Rack-Mount Power (PDU1230) https://www.amazon.com/dp/B0007YG85A?ref=yo_pop_ma_swf
https://www.amazon.com/Tripp-Lite-Outlets-Rack-Mount-PDU1230/dp/B0007YG85A/
Just swap the socket to a L6-30 and run with it :)
I found a custom cord page on that site:
https://www.stayonline.com/custom_power_cords.aspx
I'm not sure how it validates the configuration since receptacles have different wires/grounding but they have an email you can contact on there for guidance.
If it's possible to change that plug into a NEMA L5-30 (which it seems is possible on that custom cord page) then op could get a PDU like this:
https://www.amazon.com/dp/B000083KIV
That might be a little overkill for what op needs.
Another option to consider is instead of using the C13 to NEMA 5-15 cables from your PSU, you can use C13 to C14 to a PDU that accepts them which would run your PSUs at 240V instead of 120V. Then instead of the NEMA 10-50 to L5-30 op could get a cable that does NEMA 10-50 to L6-30 and a PDU like this:
https://www.amazon.com/dp/B0007YG85A
This is all operating under the assumption that it is possible to convert 10-50 to L5-30 or L6-30. NEMA 10-50 is non-grounding so that may be an issue.
These are all running:
This was the UPS that was purchased. https://www.cdw.com/product/APC-Smart-UPS-SRT-6000VA-RM-UPS-6000-Watt-6000-VA/3590615?cm_ven=email&cm_cat=ET_BC&cm_pla=MKT14Q076adu0000p0000&cm_ite=MKT14Q076_20180201_TRIG_PRODCATCH_0_CTRL_A&etsi=12258963&etsu=&obem=r6tIoIA1Z0S7QJ6YyY4EeD30ItfeRgzMhoxC7JcVWmc%3D
As for a rack we have a single rail rack about 6 foot tall. Nothing special. The company I work for is moving their servers back in house so they never had a heavy duty rack. Currently holds our ASA, Switch, PBX system, and a couple other odds & ends.
The PDU I was looking at on amazon is here - https://www.amazon.com/gp/product/B0007YG85A/ref=ox_sc_act_title_5?smid=ATVPDKIKX0DER&psc=1
Thanks for all of this!
So please someone correct me if I'm wrong. I believe you need a L6-30r recepticle with a L6-30p pdu and use c13 to c14 cables preferably 14awg. [Cable] (https://www.amazon.com/gp/aw/d/B0027JTJ22/ref=mp_s_a_1_6?ie=UTF8&qid=1522540645&sr=8-6&pi=AC_SX236_SY340_FMwebp_QL65&keywords=c13+to+c14+power+cord) [pdu] (https://www.amazon.com/gp/aw/d/B0007YG85A/ref=mp_s_a_1_1?ie=UTF8&qid=1522540759&sr=8-1&pi=AC_SX236_SY340_FMwebp_QL65&keywords=tripplite+pdu&dpPl=1&dpID=31M8t%2BMq9yL&ref=plSrch)
For power, you'll want to go with 220v (it's more efficient). You'll need to know the draw for your power supply and the load (amps) it puts on the circuit. For example 1400w @ 220v = ~6.36amp. Because it's constant draw, you don't want to exceed 80% of the circuit's max capacity.
For my units, I installed 2 x 30amp 220v breakers in my panel and used a few PDU's (https://www.amazon.com/Tripp-Lite-Outlets-Rack-Mount-PDU1230/dp/B0007YG85A/) with a NEMA L6-30P connecters and C14 to C13 power cables that connect it to the power supplies.
Could use one of these adapters along with one of these PDU's. We use a similar setup with an unused NEMA 14-50 outlet.
Which conversion cables are you referring to?
Here's my planned setup. From the wall socket which is a NEMA 14-30R I plan on plugging the following PDU into it https://www.amazon.com/Tripp-Lite-Outlets-Rack-Mount-PDU1230/dp/B0007YG85A
with the following adapter https://www.amazon.com/gp/product/B077V2JSVV/
Now the question is do i need to use any special PSU cables? Should I use the C19 ports on the PDU or are the standard C13 cables fine?
I plan on running 5 rigs, each rig is pulling about 750 from the wall when plugged into a standard 110 wall outlet.