Reddit Reddit reviews Wago 221-415 Lever-Nuts 5 Conductor Compact Connectors 10 PK

We found 10 Reddit comments about Wago 221-415 Lever-Nuts 5 Conductor Compact Connectors 10 PK. Here are the top ones, ranked by their Reddit score.

Industrial & Scientific
Electronic Components
Interconnects
Interconnect Terminals
IDC Electrical Terminals
Wago 221-415 Lever-Nuts 5 Conductor Compact Connectors 10 PK
Connect any combination of solid, stranded, and flexible copper wires faster and more reliablyMinimize space consumption in the junction box by 40% compared to 222 SeriesVisually inspect for proper strip length and complete wire insertion through its transparent housingOperate comfortably and with lower operating forces by using familiar orange leversBag of 10 with instructions card.
Check price on Amazon

10 Reddit comments about Wago 221-415 Lever-Nuts 5 Conductor Compact Connectors 10 PK:

u/bal00 · 2 pointsr/AskElectronics

Hm, it's not very complicated though. If you cut the cable, there are 8 wires inside: 3 black ones, 3 yellow ones, a blue one and a red one.

You connect all the black ones and the blue one together and wire those to the negative wire of a socket like this. Then you take the three yellow ones, connect them together and wire them to the positive wire. Done.

If you're not sure how to connect the wires together, these are more or less perfect for the job. Maybe you can find them locally.

u/LaughsTwice · 2 pointsr/MPSelectMiniOwners

Here is a small diagram i threw together for soldering in an additional fan into power pads beneath the board. I have switches in here because i plan on having a switch for the part cooling fan so i can turn it off when i want to print ABS parts.

Also, get these connectors so that you only have to solder one + wire and one - wire to the mainboard, strip 11mm of wire and plug the + into one connector and the - into another connector. Now you have the ability to add 4 accessories like extra fans or LED lighting.

u/micro0637 · 2 pointsr/electricians

This picture shows a pigtail connection.

Basically, you will join all the black wires, and all the white wires together using a cap or better yet, a set of these. in those groups you will also add a new ~5" section of wire to connect the outlet.

I wouldn't suggest trying to get all 3 sets of the current wires to the outlet, because if you dont get it tight enough you have a point of failure. ARC = Fires

u/Thomcat316 · 2 pointsr/CarAV

Ditch the converter for a NOCO battery charger/maintainer. You will thank yourself later. This one does fine with a 55Ah AGM battery. Also, don't use a wet cell battery unless it's in its own box outside the trailer.

I like your fuse block. I fused the battery feed to mine at 30A, and sized the wire accordingly - 10AWG boat cable would be perfect. All the fuses in my Blue Sea Systems fuse block are 10A and under.

Grab some LED voltmeters and mount one inside and one near your fuses. And one in your car, and....

Unless you need a separate distro bus, I'd skip that. I am using Wago 221-415 connectors as mini bus bars as needed - run a wire from the fuse panel into the cabin, then up to four additional circuits from that point - lights, etc.

You will find that your main switch panel is less functional than you hoped it would be. I recently removed mine. Individual switches at point of contact are much more user-friendly.

We loved our Fantastic Fan, and I've heard great things about Maxx Fans, but we went back to a solid roof with vent fans in the galley bulkhead.

Multicolored LED strips are fun! We are currently installing two circuits of them in the galley. When you set yours up, make sure you install a controller with non-remote controls. We have had some of the remotes fail, and at least one of them couldn't be replaced. Superbright LEDs currently has a stunning deal on one that fit our needs.

LED strip channels are a good idea. Also get the long clips, which hang on to the channel better.

Your under-cabinet lighting is probably on a 12V wall-wart. Cut it off and hook the LED strips right into your 12V system.

For wiring, get a spool each of 22AWG, 18AWG and 14AWG tinned copper cable; molded cable (lamp cord style) is acceptable. We have used Wiremold NMW1 raceway and surface mount boxes to keep things simple and tidy. Where things turn corners we leave the wires exposed instead of going nuts with the corner and tee fittings.

u/smallfeet_HUGETOES · 1 pointr/microgrowery

They are pc fans. I guess I am trying to find out if it is possible to use 2 of the 12v 1Amp drivers to run 3 fans at 12v and 666mA, instead of 1 driver that is currently running them at 12v 333mA to each fan. -- and keep from hitting them with 24v.

I am using wago connectors for my wiring. So if I just plugged in an additional driver, would this double the overall output to 24v 2Amps, or does it stay at 12v and just double the Amperage since each driver is only putting out 12v. ??

u/the_real_sasquatch · 1 pointr/microgrowery

Its very easy to wire these up. The first image at this link shows a good way to wire them. To do it that way, you need 10 Wago 221-415 lever nuts.

You can use thermal tape to attach the strips to your aluminum frame, if you don't want to drill a bunch of holes. That makes it a little easier to assemble.

Definitely do it yourself. If you have any questions, post them on here, or in the forums on LEDBuilder.com, and someone will help you get it wired up.

When I said "not much room for error", I meant that if one or two strips get disconnected, the driver will deliver more power to the remaining strips than their max rating. That is very unlikely to happen. So, don't worry about it much. Just make sure all your connections are good before you power it up.

u/ZorzStudios · 1 pointr/DIY

Forgive me if it sounds ignorant: is junction recommended for safety/neatness or is it a technical must, as opposed to twist-on wire nuts I thought of using? If it's a must, would it be something like these (terminal blocks):

https://www.amazon.com/Wago-221-415-LEVER-NUTS-Conductor-Connectors/dp/B06XH47DC2
https://www.galco.com/buy/Bussmann/TB100-04

I'll mount the sticks on the outside of the rim, bringing the wires along the spokes to the center of the wheel.

u/TurnbullFL · 1 pointr/electrical

Wago lever nuts are the way to go.

I'll even give you a link to the 5 port ones:
20 Amp 5 port.
30 Amp 5 port.