Reddit Reddit reviews Wright's Copper and Brass Cream Cleaner - 8 Ounce - Gently Cleans and Removes Tarnish Without Scratching

We found 8 Reddit comments about Wright's Copper and Brass Cream Cleaner - 8 Ounce - Gently Cleans and Removes Tarnish Without Scratching. Here are the top ones, ranked by their Reddit score.

Wright's Copper and Brass Cream Cleaner - 8 Ounce - Gently Cleans and Removes Tarnish Without Scratching
Long-Lasting Shine - The finest ingredients keep copper, bronze & brass beautiful for many years to comeEasy - It takes just seconds to effortlessly polish, rinse & dry for a brilliant, mirror-like shineEffective - Helps bring your copper back to its original beauty by erasing the discolorationProtect - Anti-tarnish formula leaves behind a protective coating that delays tarnish from reformingUse On - Tarnished copper mugs, pots, pans, sinks, doorknobs & other copper pieces around your home
Check price on Amazon

8 Reddit comments about Wright's Copper and Brass Cream Cleaner - 8 Ounce - Gently Cleans and Removes Tarnish Without Scratching:

u/wolf_pack1997 · 5 pointsr/OnTheBlock

https://www.amazon.com/Wrights-Copper-Cream-Cleaning-Polishing/dp/B0083PEZ00 My old man uses this make sure its real copper, but if it's looking like the statue of liberty it probably is.

u/brubakerp · 4 pointsr/metalworking

I would start with this stuff in a small area and see how it works out before you get into any sanding.

If you do have to sand, I would use a non-woven abrasive drum similar to these in the finest grit available. Only go coarser if you have to as you'll be making more work for yourself. I wouldn't sand in circles, straight sanding lines will look better if you cant get them all out. If you don't have a lot of scratches, start with a 220 emery cloth. Then move on to a buffing wheel and compound if needed.

u/Vortexbig · 1 pointr/HomeImprovement

I've used Wright's Copper Cream on heavily tarnished copper bells and it worked pretty well. I used hot water on the metal first, then scrubbed with a sponge, then rinsed. It does take some elbow grease, but if you can warm up the metal it comes off more easily.
https://smile.amazon.com/dp/B0083PEZ00/ref=cm_sw_r_cp_apa_i_h9XUCbY93CZ26

u/themasecar · 1 pointr/drums

That's a bronze shell, not a brass shell. Close enough, but Ludwig didn't make non-plated brass shells until recently.

I'd get some Wright's Copper Cream and a microfiber cloth and just take your time and work the shell over. If the tarnishing is really bad, you can get some fine-grade steel wool (hardware stores generally have down to 0000) and use it with the Wright's polish.

I use Wright's Copper Cream to clean my cymbals too, when I feel like doing that. Works better than anything else I've ever seen.

u/honeydothis · 1 pointr/DIY

I have a copper sink that looks exactly like that after a couple weeks of use. This stuff is what you need. Makes the sink look brand new and it's super easy to use!

u/arizona-lad · 1 pointr/HomeImprovement

Take one off and polish it. Almost certainly copper plated:

https://www.amazon.com/Wrights-Copper-Brass-Cream-Cleaner/dp/B0083PEZ00

u/ground_hogs · 1 pointr/jewelrymaking

Wright's Copper Cream works wonders. Rub it onto the copper and let it sit for a little while (5 min or so) and then rub it off under running water. I'm not sure this will remove sticky tape residue, but it will give a nice polish, so this could be a final step after following /u/fashionforward's advice.