Reddit Reddit reviews Yost Vises 905-AS 5" Heavy Duty Steel Bench Vise

We found 1 Reddit comments about Yost Vises 905-AS 5" Heavy Duty Steel Bench Vise. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Hand Tools
Power & Hand Tools
Bench Vises
Yost Vises 905-AS 5
Bench-mount vise with 5" nominal top jaw width and 1/2"- to 1-1/2"-diameter pipe capacity provides clamping action for light-duty applications360-degree swivel base adjusts the direction of the jaws for proper placement and locks in placeCast steel body is painted black for mild protection against corrosion and has flat portion that acts as a reinforced anvil and an additional work surfaceReplaceable top jaws and built-in pipe jaws are grooved for enhanced gripMain screw that controls the jaws is covered by a bar to protect it from damage
Check price on Amazon

1 Reddit comment about Yost Vises 905-AS 5" Heavy Duty Steel Bench Vise:

u/Jaxxbeachguy ยท 2 pointsr/rosin

This is my set up. Really, really easy. I dont have a garage full of tools and i still thought it was easy.

Disassemble this https://www.amazon.com/gp/aw/d/B01M14RI79/ref=zg_bs_11058261_7?ie=UTF8&psc=1&refRID=F6E9C1ERF8C0HBFJSA98 (having some of those really small screwdrivers like you'd use to work on eye glasses makes this part cake)

https://www.amazon.com/gp/aw/d/B00ZS6JU02/ref=mp_s_a_1_7?ie=UTF8&qid=1510258631&sr=8-7&pi=AC_SX236_SY340_QL65&keywords=aluminum++1%2F2+inch&dpPl=1&dpID=31FkfqMeaYL&ref=plSrch use a dremel to cut this into plates to sit on both sides of each of your hair straightener heat plates. Having the aluminum against the back of the hair straightener plate will keep you from smashing those wire leads and allow you to put more pressure.

I tried a few diff arbor presses and vises, for my small nug presses (i press a nug at a time, its just for me and rosin lasts me a really long time in my wax pen) .... the 5 inch model of this one gives me plenty of pressure and doesnt break the bank. https://www.amazon.com/gp/aw/d/B003JSY8S0/ref=mp_s_a_1_7?ie=UTF8&qid=1510258796&sr=8-7&pi=AC_SX236_SY340_FMwebp_QL65&keywords=yost%2B5%2Binch%2Bvise&dpPl=1&dpID=41QF1yC8WyL&ref=plSrch&th=1&psc=1

And thats it. At first i used jb weld to hold my plates to each other but found that metal wire (with slots cut into everything to make the wire stay in place and the plates to meet flush) was far easier. Only tool i really used was a dremel and of course my laser thermometer to constantly check accuracy of the temps. I get great results with this setup and it was super cheap. I can post pics of mine if you want. Got it zip tied to the inside of a milk crate to make it portable and stand upright on its own. It looks pretty rough but works great.

Edit. ... personal opinion here ..... but beware of builds using arbor presses, yeah they work, but for my money its easier to twist that 5 inch vise tight really hard then wait and watch the timer...... vs having to stand there with all my weight leaning on an arbor press handle for 60 seconds at a time to keep pressure on. That yost 5 inch vise gives me better returns than i got from an arbor press and it's less work.


Hope i dont get laughed too hard but here is my Frankenstein https://m.imgur.com/a/bOZ1P (note the notches made with the dremel to keep the wire from sliding around the vise when you tighten it.) Works like a champ and cheaply replaced parts.