Best combination wrenches according to redditors
We found 132 Reddit comments discussing the best combination wrenches. We ranked the 88 resulting products by number of redditors who mentioned them. Here are the top 20.
We found 132 Reddit comments discussing the best combination wrenches. We ranked the 88 resulting products by number of redditors who mentioned them. Here are the top 20.
![TEKTON 1916 Combination Wrench Set, Inch/Metric, 1/4-Inch - 1-Inch, 8 mm - 24 mm, 24-Piece [Older Model]](https://m.media-amazon.com/images/I/41YCDbEo1cL.jpg)
Checkout Tekton, can get all their stuff on Amazon and I've been very pleased with the stuff I have from them. Best part is for the most part they don't skip sizes in their sets like other cheap stuff.
Check out, TEKTON Combination Wrench Set with Store and Go Keeper, Metric, 8 mm - 22 mm, 15-Piece | 18792 https://www.amazon.com/dp/B00OZJN3PQ/ref=cm_sw_r_cp_apa_YfpWAbSSBGA74
I have this set and a couple others. They have been awesome.
GEARWRENCH 1/4" 12 Point Ratcheting Combination Wrench - 9008 https://www.amazon.com/dp/B0002NYD44/ref=cm_sw_r_cp_api_i_G.tMDb9J0X6AB
hate flats, learn how to switch out tubes, saved me a lot of hopelessness and the gear required is pretty light to carry around.
lever
tubes
ratchet wrench 15mm
portable air pump
back up and running in 15-20 min.
Always great to see the yellow stickers!
Just a heads up too, this was on slickdeals today as Amazon's deal of the day:
https://www.amazon.com/gp/product/B0002NYD1W/ref=ox_sc_act_title_1?smid=ATVPDKIKX0DER&psc=1
Craftsman is junk; Husky is decent; Snap On is overpriced.
I re-tooled last summer from my old Williams set. Here's what I wound up with:
-Snap On GF80: 3/8" drive ratchet, got it off ebay for $50. I probably wouldn't buy again, but it is very nice.
-Pittsburgh Pro extendable 1/2" drive and flex-head 1/4" ratchets: Less than $20 each, and they are 90% as good as the Snap On. I would probably buy the 3/8" instead of the Snap On, if I had to do it over again.
-Pittsburgh Pro 1/2" drive impact sockets: These boys have taken some abuse at this point, and other than the etching having been stripped off of a couple (see abuse above), they are still in great shape. $25 for shallow, $32 for deep, Metric or SAE.
-GearWrench 3/8" drive impact sockets: $60 for a pretty complete (8mm-19mm + 21mm, 5/16"-3/4") set, and they are very thin-walled so you don't really need chrome.
-Pittsburgh Pro 3/8" chrome (shallow only): $9/set for 12-point sockets, which is the only reason I got them.
-Pittsburgh Pro 1/4" chrome sockets, shallow and deep: Overpriced, really, but I got the color-coordinated ones which are pretty cool. I might go for a cheaper set if I had to do it again. $8-9/set.
-GearWrench Long Pattern Wrench Set: I got the 22-piece Metric set (6mm-32mm with some skips) for $97; I haven't bothered to get the SAE set, I just have a handful of Pittsburgh SAE wrenches on a wrench ring.
And a big rally box to put it all in. I bet you could get all of it for under $500 if you use coupons at Harbor Freight and shop around for the GearWrench stuff.
-------------------------------------------------------------
I also got a DeWalt cased set to keep in my trunk:
https://www.homedepot.com/p/DEWALT-1-4-in-x-3-8-in-Drive-Polished-Chrome-Mechanics-Tool-Set-200-Piece-DWMT75000/206510555
But I had to add some wrenches (it has 10mm, 11mm, 13mm and 14mm; wtf?!) to my trunk bag to make it "complete," and even then it has some oddness to it (3/8" drive starts at 14mm, so you'd better not have any really tight 12mm bolts...) so it might not be what you are looking for, but they make a few different sets.
----------------------------------------------------
Other things I considered:
https://www.amazon.com/Williams-50614-2-Inch-Socket-146-Piece/dp/B00HR1Q5F4
$320 for a complete Williams socket set, but the wrenches are about the same...
---------
This might be the "bang for the buck" winner, simply for the completeness of the socket sets:
https://www.amazon.com/dp/B01LYZ2IJ5
https://www.amazon.com/dp/B01MDO6L90
https://www.amazon.com/dp/B00OZJN3PQ
$270 ($180 for 1/2", $88 for 1/4" and 3/8") for a staggeringly complete set (10mm-32mm in 1/2" drive, shallow and deep, with no skips!) and then $42/set for the wrenches, 8mm-22mm.
---------
https://www.amazon.com/KD-Tools-KDT-80942-239-Piece/dp/B00OL2XFLO
GearWrench socket, wrench and allen key set, $210 for a whole bunch of tools, although they aren't the high-tooth-count ratchets.
--------
https://www.harborfreight.com/hand-tools/hand-tool-sets/301-pc-mechanics-tool-set-63464.html
Then there's this thing. It is actually quite well reviewed, and surprisingly complete on the socket side, if a little short on wrenches. It's usually on sale for $160.
---------
https://www.amazon.com/dp/B0056E11QW
https://www.amazon.com/dp/B00BT0AYG0
...and then there's the dream: If I could get away with having this stripped-down of a set... $600 for a very nice, but fairly bare-bones set. No deep-well, no 3/8" drive at all (hello, super-tight 12mm bolts!), and only great big long extensions... if you never need to get into really tight spaces, maybe. The 3/8" drive set is another $260 on top of this, and still doesn't have short extensions or deep-well sockets.
Tekton and harbor freight are your best friend.
Go to harbor freight and get a toolbox, 3 ton jack, and 4 jack stands. A creeper is nice to have.
If you want sockets and ratchet from harbor freight, get the Icon ratchets and Pittsburgh sockets.
I suggest Tekton from Amazon. Start with the 3/8 set, then get the 1/2 and 1/4 set.
https://www.amazon.com/dp/B07P6RJXJ9/ref=cm_sw_r_cp_apa_i_UuaQDbRWPK777
That'll cover your socket needs for the most part.
For wrenches :
https://www.amazon.com/dp/B00OXUPFDU/ref=cm_sw_r_cp_apa_i_CwaQDb63MEAK1
With a toolbox, Jack, Jack stands, socket set, and wrenches, you'll be able to complete most jobs.
Over time, you'll accrue more tools as you need them. I'm a mechanic by trade and, even with a fully matured tool setup, find myself buying tools I need every once and a while.
Join us at /r/tools and www.garagejournal.com
It will back a screw out, but it won't give the tourqe to break it. These work way better in tight situations like that.
https://www.amazon.com/TITE-REACH-EXTENSION-WRENCH-TR14_38_DIY-Tite-reach/dp/B00DMHN014/ref=mp_s_a_1_2?adgrpid=57600405338&gclid=EAIaIQobChMI9O6zgM3Z5QIVBdbACh1_bw7YEAAYASAAEgJE7_D_BwE&hvadid=274748500793&hvdev=m&hvlocphy=9013479&hvnetw=g&hvpos=1t1&hvqmt=e&hvrand=5807838383904752486&hvtargid=kwd-329913341964&hydadcr=20381_9349130&keywords=tite-reach&qid=1573181297&sr=8-2
This kind of thing? Tite-reach Extension Wrench Tri-pack by Tite Reach
For tool boxes, I'd go craigslist, 100%. Get in the habit of looking for toolboxes twice a day, and you'll find a good deal eventually. I'd also recommend buying power tools on CL, especially corded ones (where you don't have to worry about a worn out battery). If you want to buy new, the harbor freight tool boxes are a great deal and work really well.
As far as tool sets, I've found it better to kinda just accumulate the stuff you need over time. To start, definitely get a good socket set with 1/4" and 3/8" drive sockets, as well as a couple ratchets. I'm partial to the composite bodied tekton ratchets on amazon, as it's great to not have to worry about dinging the paint by swinging a ratchet into it. I'd also reocmmmend getting a set of gearwrench ratcheting wrenches. They're phenomenal, and once you go to a ratcheting wrench you'll never go back.
As far as other tools, you can't go wrong with a big hammer, a set of pry bars, and a good screwdriver set. It's expensive, but the chapman manufacturing bit driver sets are incredibly well made and super versatile. It's not cheap, but it's also essentially the only screwdriver set you'll ever need. A good impact wrench can be very helpful for general use, though I'd recommend getting a set of impact-rated sockets to go along with it (the 12-point sockets in most socket sets can strip quickly when used with an impact).
Also, buy as much lighting as you can, and get something comfortable to sit on. Trust me, you'll thank yourself later.
https://www.amazon.com/TEKTON-1916-Combination-Wrench-Metric/dp/B000NQ159G
They're not top quality but for $20 you can't go wrong!
I own that Joker set. They look cool. They've got a feature list a mile long. But my Tekton wrenches are just... better. For what it's worth, the quality on the Joker's aren't even that good. Wera sent their manufacturing for the Joker's out to the Czech Republic, which is kinda like the China of Europe for cheap manufacturing.
If you need ratcheting wrenches, I'd recommend you get the Tekton WRN53170 set. 8-19mm with no skips, which is the same range as the wera plus the 9mm. And the set is only $80 for some strong wrenches with better quality control than the Joker's. Great warranty too. https://www.amazon.com/TEKTON-WRN53170-Ratcheting-Combination-Wrench/dp/B01F511TS0
If ratcheting isn't that important to you, the WRN03393 set is also great. 8-22mm with no skips. Only $50 bucks. https://www.amazon.com/TEKTON-Combination-Wrench-Roll-up-Storage/dp/B0199R9UQ4
Oh and always buy the Tekton sets with the pouches - if you like the plastic wrench organizers instead, you can always buy those separately for a few bucks, but those roll up pouches are gorgeous and strong and you can't buy them by themselves.
Anyway, sorry if I sound like a Tekton fanboy, but I own all three sets I've talked about here. I hardly use my Joker's because the Tekton sets are way better. TL:DR Jokers not worth it.
They make them, they aren't the best when you need alot of torque though.
https://www.google.com/url?sa=t&source=web&rct=j&url=https://www.amazon.com/Crescent-CX6RWS7-Combination-Ratcheting-Open-End/dp/B009L86A7O&ved=2ahUKEwjp7YO8z_vlAhWZCjQIHUx6AGwQFjAFegQIAxAB&usg=AOvVaw26sJkFimhU5lq9Sj-yTHe1
You obviously don't own these...https://www.amazon.com/GearWrench-85888-Metric-Combination-Ratcheting/dp/B000NIAKGI
Tekton wrenches: https://www.amazon.com/dp/B00OXUPFDU
GearWrench sockets and ratchets: http://www.tooldiscounter.com/ItemDisplay.cfm?lookup=KDT80300P
Kobalt cabinet I found on clearance for $160: https://m.lowes.com/pd/Kobalt-3000-35-in-W-x-47-in-H-7-Drawer-Steel-Rolling-Tool-Cabinet-Black/1000437815
Anyone have recommendations for mounting the wrench holders to the pegboard on the inside of the lid?
Gearwrenches: http://www.amazon.com/GearWrench-9416-Metric-Master-Ratcheting/dp/B0002NYD1W/ref=sr_1_3?ie=UTF8&qid=1419886288&sr=8-3&keywords=gear+wrench
I love my Gearwrench stuff. I have the ratcheting wrenches and some socket stuff, the 120XP ratchets are amazing. I always grab them before my more expensive tools.
For your budget you can get a lot of wrenches:
https://www.amazon.com/gp/aw/d/B0002NYD1W/ref=mp_s_a_1_4?ie=UTF8&qid=1511099834&sr=8-4&pi=AC_SX236_SY340_QL65&keywords=gear+wrench+ratcheting+wrench+set&dpPl=1&dpID=51Ney6Tn4JL&ref=plSrch
https://www.amazon.com/gp/aw/d/B0002NYD12/ref=mp_s_a_1_5?ie=UTF8&qid=1511100241&sr=8-5&pi=AC_SX236_SY340_QL65&keywords=gear+wrench+ratcheting+wrench+set&dpPl=1&dpID=51MI3AtWo7L&ref=plSrch
https://www.amazon.com/gp/aw/d/B01MZ66M6O/ref=mp_s_a_1_27?ie=UTF8&qid=1511100494&sr=8-27&pi=AC_SX236_SY340_QL65&keywords=gearwrench+stubby
[Complete enough?] (https://www.amazon.com/dp/B00H2W7LVK/ref=cm_sw_r_other_awd_8Ec3wbE12RGJD)
I agree, build you own kit. Below is my take. Know that some of those tools are not for every day use in networking, but who can resist getting more tools? Also, if you get all of these I realize it will be over $200. So, just use this list as a guide not a definitive list.
BAGS
ETHERNET TOOLS
SCREWDRIVERS
PLIERS and WRENCHES
POWER
MISC
SUPPLIES
For 3/8 impact sockets go with the Sunex 3342 master set. It has both SAE and Metric and comes with both short and deep well for $68 and they're made from Cr-Mo instead of Cr-V like the Tekton ones are.
Edit: For wrenches check out the Tekton 18772 and 18792 sets, I own both of these sets and like them a lot and just now noticed that they're on sale right now.
Well, you wanted a project, and you wanted to learn...
To be blunt, Don't dive into this any further until you have learned how to get stripped fasteners out. It is a skill that is 100% necessary to learn, and ignoring it now will just cause heartache down the line. Right now, those two fasteners are worth exactly what you paid for the bike, because until you get them out, the bike is worthless. If you spend money fixing another problem, these will still be there, and they will still be broken, and if you can't fix them later, then all the time and money you spent elsewhere on the bike is for not.
There are millions of discussions on the internet discussing the removal of stuck fasteners. Some people are full of shit, others know what they are talking about. Given that this seems to be an issue of ferrous fastener in aluminum block, an easy-out is NOT the way to do it... I give you a 99.95% chance of breaking it off in the fastener.
Before you do anything else, buy the following tools:
HAND impact driver. (I've used many different ones, this is my preferred one)
Flex-head ratcheting box wrench set. When I was an industrial mechanic, I used these almost to the exclusion of ratchets. They fit in tighter places than ratchets, and because of physics, don't round fasteners as much.
A set of GOOD drill bits and cutting oil.
A Torque Wrench.
A service Manual for the machine you're working on.
DO NOT USE ADJUSTABLE WRENCHES at this stage in your adventure. They are a convenience trap, and are much more likely to round off a bolt head than a box wrench. Box wrenches and sockets are the least likely to round heads, because they apply force all around the fastener's head.
Aside from very specific circumstances, you should not be using power tools for anything mechanical. Any time they save on one task will cost you time unfucking your mistakes somewhere else until you learn the proper way to do things. (It's super easy to fuck a screw head, or cross thread a bolt if you try to zip it with a rattle gun.)
As far as the fasteners, if there is clearance, you can cut a slot in the head, and use a flat-blade screwdriver bit on your hand-impact driver to back the fasteners out. Alternatively, if there is at least 1/4in of thickness between the head of the fastener and the engine block, you can drill the head off, and then use vice-grips on the shaft of the fastener.
I have those and these from Tekton. I honestly haven't needed the angled wrenches for much yet, but I didn't notice anything wrong with the combination wrenches.
I got my first automotive job about 2 years ago. I am also a nut at buying tools. I started off with an 8-drawer Cornwell cart. Loved it. Once I got a decent amount of tools, I bought a SO Classic 96 box. Worst decision ever. Granted it was a fantastic box. But for $6000? No. I was paying about $200/mo (my minimum payment was only $38/week but I wanted to put more down)... the interest rate... 22% which I was told was average. I cant tell you how stupid I felt seeing that, out of that $200/mo, $60 was going to a finance charge. I paid until I got down to owing $3,500, bought it completely with a credit card that I got 18/mo-no interest and then sold the box for $3,000 cash. I took a $500 hit, but it sold after 3 days and I wouldve paid more than $500 if I kept paying to SO.... I went back to the cornwell cart for about a year and realized that SO and their interest rates suck and I really didnt need that box at that time. I just bought a used Cornwell 58" box with a hutch for $4,500 (normally $9,000 brand new. Got repo'd from some guy that stopped making payments. Don't be that guy) at 9% (lowest they got) and sold the Cornwell cart to a coworker for $500. Couldnt be happier.
The ONLY hand tools that are absolutely a must from SO, are their ratchets, pry bars and cordless ratchets. Best out there, no doubt about it. Get long flex head ratchets
For sockets/extensions, Gear Wrench. You can get shallow and long metric sockets from your local Advance Auto Parts from a pretty good price. Gear Wrench also makes Torx and Hex (allen) sockets.
For wrenches.... Gear Wrench or Cornwell. Also, these are my favorite... http://www.amazon.com/ATD-Tools-99650-Ratcheting-Wrench/dp/B008FXN0VK
Deep Impact sockets, Harbor Freight. Seriously, they are impact sockets, they rarely break and youll be chucking them on the ground to loosen a bolt that got stuck. No need for anything fancy. I dont really see the need for shallow impact sockets
For pliers, Knipex Knipex Knipex... You will thank me later. Snap On prices, but 10000X better quality. Snap On pliers suck ass and wont warranty the teeth on them. Knipex does warranty the teeth. Just look at their needle nose pliers... every tooth on them lines up perfectly (point to point) with each half. Their long-handled Wire cutters are awesome and their channel-lock-style pliers just bite harder the more pressure you apply when youre breaking something loose. Ze Germans might make shitty cars, but they do know how to make quality tools.
For cordless impact tools, Ingersoll Rand. Pricey, but they are the best out there. I have the 1/2" and 3/8" IQ 20V series. Little secret. Look for when they run a special on the 1/2" impact that comes with a charger and 2 batteries. The 1/2" impact batteries also fit on the 3/8" impact so you can save some money and just buy the bare 3/8" impact tool. The batteries for the 1/2" are 3 amp while the 3/8" are 1.5 amp but the 1.5A batteries wont work on the 1/2" impact.... sorry if that was hard to read.
I know that having the Snap On name stamped on everything you own is every new mechanics dream. Been there, regretted that. So much money wasted. Snap on USED to make the best of the best and SOME of their stuff still is the best. But they have gone down hill and more and more of their tools are made overseas now. Granted, some overseas made tools are actually top notch. Youll never be able to convince anyone that, but its true. A guy at my shop has a ton of older Snap On stuff and works just fine. But every time one of his 20 year old tools breaks, he gets upset. SO still warranties it, but then he has to keep getting it warrantied because the quality isnt there anymore and they keep breaking.
Start small, avoid too much debt, and fuck SAE sizes except for 7/8". I dont think car manufacturers use them any more
Why not just this?
Tite-reach Extension Wrench Tri-pack https://www.amazon.com/dp/B00DMHN014/ref=cm_sw_r_cp_api_i_665WDbBEBM07B
I almost bought them a few years ago when I decided on upgrading from my Gearwrench set. I work industrial maintenence, and even then do I rarely come across situations when the Jokers would actually make a difference.
I ended up going with a Blackhawk set. Having a reversible ratcheting head was more important to me
https://www.amazon.com/dp/B004HMDKZE/ref=cm_sw_r_cp_apa_i_ukRjDb14FTP73
If you're just looking for a set for the house, and not work, I suggest just going with a Gearwrench set
these are less than half and use a big shoulder on the ratcheting section which makes them more fun to use, but they aren't quite as sturdy. I have a set of each and I use the cheaper ones more, but they aren't good for breaking tough nuts/bolts loose like the Matco ones are. They are also all spline drive so they are great at gripping stuff that is partially rounded and star heads.
I set up a tool box for my younger brother this year and this is the socket set I picked for him
GearWrench 80550 57 Piece 3/8-Inch Drive 6 Point Socket Set https://www.amazon.com/dp/B000NICEVW/ref=cm_sw_r_cp_api_2D.wybBAS3832
I also got the
GearWrench 81210P 120XP Cushion Grip Flex Teardrop Ratchet, 3/8-Inch https://www.amazon.com/dp/B00BTEXV52/ref=cm_sw_r_cp_api_sF.wyb6FDSS1G
Wrench set
TEKTON 90191 Combination Wrench Set with Store and Go Keeper, Inch/Metric, 1/4-Inch - 1-Inch, 8 mm - 22 mm, 30-Piece https://www.amazon.com/dp/B00OXUPFDU/ref=cm_sw_r_cp_api_mG.wybM57PJSQ
Basic stuff
Ball pein hammer
Dead blow hammer
Feeler gauge
Brass drift pin
Sparkplug sockets
Assortment of pliers
Assortment of screwdrivers
Crescent wrenches
The US General 5 Drawer Tool Cart is a beginner mechanic's best friend.
A word of warning though; don't buy combination wrenches from Harbor Freight. They skip sizes, and that's not what you want when you're working on several types of cars that can't agree on standard sizes.
IMO this is the best set you can get for your money, but you will need to get a 23mm separately if you ever want to change the diff oil in a Miata.
(PROTIP: 15/16 is 24mm and 5/16 is 8mm.)
Amazon
oooo I do like them....
insert [spongebob I dont need it meme] here
https://www.amazon.com/TEKTON-WRN77164-Flex-Head-Ratcheting-Wrench/dp/B01F512HOU/ref=sr_1_fkmr1_1?ie=UTF8&qid=1540946580&sr=8-1-fkmr1&keywords=double+box+flex+tekton
I've been happy with my Tekton metric set. The prices have gone up though, I got my metric set for about $35 in early 2017, but now they're about $50 each or $100 for both the SAE/Metric set.
Here's the SAE/Metric sets: https://www.amazon.com/TEKTON-Combination-Wrench-Keeper-Metric/dp/B00OXUPFDU/ref=sr_1_3?keywords=tekton+wrench+set&qid=1557847901&s=gateway&sr=8-3
Gearwrench. https://www.amazon.com/GearWrench-81919-44-Piece-Non-Ratcheting-Combination/dp/B00H2W7LVK/ref=sr_1_24?s=power-hand-tools&ie=UTF8&qid=1540036597&sr=1-24&keywords=wrench+set
Tekton. https://www.amazon.com/TEKTON-Combination-Wrench-Keeper-Metric/dp/B00OZJN3PQ/ref=sr_1_5?s=power-hand-tools&ie=UTF8&qid=1540036468&sr=1-5&keywords=wrench+set&dpID=51%252BDoXrWhZL&preST=_SY300_QL70_&dpSrc=srch
I don't like a raised panel wrench. You could also keep an eye out for craigslist snap ons or Mac.
I would carry a 15 mm short ring spanner (I think Americans call this a stubby box wrench). The other end doesn’t matter but will most often be open, making the tool a combination spanner if you’re looking for terms to Google.
This frees you to choose a smaller multi-tool. And it’s much stronger than anything in a multi-tool. Push it with your foot for higher torque if necessary. Use the ring/box end that allows much higher torque than the open end before deforming tool or nut.
Also much smaller, lighter, and capable of much higher torque than an adjustable spanner.
Example from a known good brand.
I just put together a tool kit for my BRZ, and I ended up getting a set of Tekton metric sockets and a Tekton low-profile 3/8s inch ratchet. I've used Tekton quite a bit and I found them to be pretty great. These metric sockets will cover just about everything on the car that can be loosened or tightened with a socket, and since they're deep sockets you can loosen lug nuts with them.
I'd suggest getting a breaker bar or torque wrench if you want to get an additional accessory. The breaker bar is great for loosening tough nuts, and the torque wrench is terrific for tightening a fastener to the exact amount of force it specifies in the manual.
If you really want to go above and beyond, an open ended wrench set (also metric) can be great for when a socket just won't fit. They even make a version with a built-in ratcheting mechanism
In summary, a metric ratchet set that goes from about 8mm to about 20mm is a great gift idea, and you can easily add on other accessories or wrenches if you want to make your gift a bit bigger. I can personally vouch for the Tekton stuff--sure it's not the most expensive fancy set of tools out there, but they look, feel, and work well.
Hope this helps!
Wiha makes "softgrip"wrenches that basically have a coating of soft material around the wrench grip.
Mountain Flexible Ratcheting Wrenches have a pretty unique handle/ergonomics that might interest you.
Other than that, the Gearwrench X-beam wrenches are pretty damn ergonomic if you ever get a chance to handle them.
Serpentine belt tool: www.amazon.com/gp/product/B0002WSFTO
I know it will be of use for your 2008.
Thanks a ton!
One:
What is the benefit of a 3/8 set when I have a 1/4 and 1/2 set? The physical socket sizes are more or less all covered, I believe, though I will check to make sure.
My friend told me I should get a 3/8 set simply for ratchet size reasons - he thinks that the 1/2 ratchet is simply too big to fit in most places.
On the other hand, I have a 2000-model american car, so there is a lot of space... and I'm simply not sure that a 3/8 set will be able to take the torque I need to get a lot of things loose.
I really appreciate the advice, by the way. If you think it's indispensable regardless of the above, I'll get one.
Two:
What makes a very good screwdriver set? What should I look for? I assume you mean I should get a set of fixed screwdrivers, instead of one screwdriver with replaceable bits. (And honestly, as much as I like my screwdriver with bit set, it won't handle the torque I need for cars, so this is probably a good idea.)
Three:
I'll look into what channel lock pliers are. I have normal pliers and cutters. I'll get vice grips.
Four:
Is this a double sided line wrench that you mention? I have this set of normal wrenches.
Five:
I do have a bunch of nice bright headlamps. I find headlamps to be awesome for car stuff... light goes where your face goes. Would you recommend any other lights? I think I've seen some magnetic LED lights, where you stick 'em to the car to keep the light on a certain place.
Six:
I'll look into an electric impact wrench.
Seven:
I have a half inch breaker bar, two feet long. Do I need the 3/8ths? Same question as above basically. And I have the adapters.
Eight:
Great call on the ratchet straps, I keep forgetting how great those are.
---
So a few questions above, and I'll get ratchet straps, channel lock pliers, vise grips, double sided line wrenches, and look into an electric impact.
I've got one about that length in my Ramblin' Roll. It was part of a set but I'm sure you can find them individually. Here is one for you
Best deal for starter sets is these two together from tool discounter, https://www.tooldiscounter.com/ItemDisplay.cfm?lookup=KDT80550P&source=froogle&kw=KDT80550P&gclid=Cj0KCQjw9NbdBRCwARIsAPLsnFYxgfkreQ3glGbzdspWMV5mD8aWE2VIKi9KSriaOK02IKFZc7gz96waAofvEALw_wcB plus the 1/2 kit of you need it/really want it. Add this https://www.sears.com/kd-tools-5-ton-3-2-reversible-puller/p-00999873000P when they go on sale more or take advantage of the spend $75 get $75 back in points. Bondhus Allen wrenches, Bondhus 22199 Hex L-wrench Double Pack, Long Length, 12137 (.050-3/8-Inch) & 12199 (1.5-10mm) https://www.amazon.com/dp/B000E7VG5C/ref=cm_sw_r_cp_apa_kqKTBbVWJSHZT add whatever screwdrivers you fancy and you're probably under the cost of that kit with better stuff
Edit: looked at the link again and missed some stuff, get this extension set at Sears with those bars and get to $75 to get the $75 back https://www.sears.com/craftsman-20-piece-drive-tool-accessory-set/p-A009988410 wrenches if you want standard 12 point ones like are in the kit, wait for the holiday tool displays to get put up and get the 28ish piece husky set at home Depot for like $30 or step up to this gearwrench set https://www.tooldiscounter.com/ItemDisplay.cfm?lookup=KDT81923&source=froogle&kw=KDT81923&gclid=Cj0KCQjw9NbdBRCwARIsAPLsnFbqtP_Ead7DMocuNLPeeDtKV65LkSIchO6oACKELQrmh5-sodXcnlIaAvhEEALw_wcB or like a tekton set like this TEKTON Combination Wrench Set with Store and Go Keeper, Inch/Metric, 1/4-Inch - 1-Inch, 8 mm - 22 mm, 30-Piece | 90191 https://www.amazon.com/dp/B00OXUPFDU/ref=cm_sw_r_cp_apa_gxKTBb29EQ6GK if you prefer 12 points for some reason
Album:
https://imgur.com/a/o2Ri86I
After turning my Gearwrench set for a couple years, I finally pulled the trigger on an upgrade. I'm a huge fan of Proto (best ball peen on the market), so went with their Blackhawk set of wrenches.
Amazon link :
https://www.amazon.com/dp/B004HMDKZE/ref=cm_sw_r_cp_apa_i_JreBCb3B7CZCG
Sizes 8mm-19mm
Are you trying to break the pulley nut free? Is so, a serpentine belt tool set, or something similar, will make your life easier.
https://smile.amazon.com/TEKTON-WRN53118-Ratcheting-Combination-Wrench/dp/B01F511QKQ/ref=sr_1_5?ie=UTF8&qid=1511033007&sr=8-5&keywords=tekton+ratcheting+combination+wrench
You can see the convex sides on the box end in their diagrams.
And in a 12 point combination wrench:
https://smile.amazon.com/TEKTON-16-Inch-Combination-Wrench-WCB23033/dp/B06XTY1KCR/ref=sr_1_1_sspa?ie=UTF8&qid=1511033199&sr=8-1-spons&keywords=tekton+ratchet+combination+wrench&psc=1
Also the harbor freight pittsburg and pittsburg pro ratcheting combination wrenches, but they don't have a diagram.
https://www.harborfreight.com/7-piece-sae-ratcheting-combo-wrench-set-96654.html
Craftsman example (No diagram)
https://www.craftsman.com/products/craftsman-professional-1-1-2-full-polish-long-pattern-wrench-12-pt-combination?taxon_id=1893
What you are describing sounds like this:
GearWrench 9008 1/4-Inch Combination Ratcheting Wrench by Apex Tool Group http://www.amazon.com/dp/B0002NYD44/ref=cm_sw_r_udp_awd_YDS0tb09EZ2G5
But this may be a better fit:
Neiko 03044A Mini Ratcheting Screwdriver and Bit Set, Pocket Size Close-Quarters ,1/4-Inch Drive by Neiko http://www.amazon.com/dp/B000XYOUS6/ref=cm_sw_r_udp_awd_8FS0tb012H4Q2
Hope this helps!