Best tool sets according to redditors

We found 619 Reddit comments discussing the best tool sets. We ranked the 262 resulting products by number of redditors who mentioned them. Here are the top 20.

Next page

Top Reddit comments about Tool Sets:

u/OpticalPrime · 104 pointsr/Skookum

https://www.amazon.com/KD-Tools-80319-Master-Socket/dp/B00LH7DM14

This is my go-to gift for car buddies when I don’t know what to get.

u/shadow_of_octavian · 30 pointsr/college

Tool Kit, best graduation present I ever got for college. Besides that, really depends who you are. I would recommend a board game for when you need something to do with roommates. From Settlers to Catan, Boss Monster, or a deck of cards any thing that can get a group of people playing.

u/fs337 · 26 pointsr/Rainbow6

It's actually a real breaching hammer. It's the Gerber Ding Dong Breaching Tool, for those really stubborn baby food jars.

u/Jig5 · 25 pointsr/homeowners

You're looking for this kit: O'BERRY ENTERPRISES 3233"SQUEEEEEK NO MORE" FLOOR REPAIR KIT https://www.amazon.com/dp/B0006IK8YE/ref=cm_sw_r_cp_api_CHd8Bb17FJMWG

I've used it on stairs and it's worked great but haven't had the courage to use it on the floors yet as I'm afraid to miss a joist and have an unnecessary hole in the floor.
They have videos of people using it and it works well.

The powder method doesn't work and pediatricians nowadays don't want powder getting anywhere near an infant.

u/tripwire1 · 18 pointsr/malelifestyle
  • Screwdrivers

  • Needle nose pliers

  • Sockets

  • Electric Drill

  • Putty knife and spackle

  • Level

  • Hammer

  • Work gloves

  • Stud finder

  • Tape Measure

  • A good, small flashlight--keep one in the car and one in the home

  • A toolbox to store it all


    Specifically for my truck I have:

    a flexing spark plug socket like this one and spark plug pullers

    An OBD II Scanner

    Auto jack(s)

    An oil pan and an oil filter wrench or other tool that makes the filter easier to remove

    And, of course, jumper cables, a poncho or two, some spare water bottles and all that good stuff that stays in the truck too.


    Edit: Honestly, this is a great place to start--Stanley 65-Piece Homeowner's Tool Kit

u/[deleted] · 17 pointsr/techsupport
  • I couldn't have a repair kit without these cables. Need to hook a hard drive up but don't want to put it inside of a computer? Done! You can also get a usb 3.0 if you're so inclined!

  • Everyone loves magnetized screwdrivers..so I bought this set and it seems to be of good quality so far.

  • Need to do some fine adjusting and use a strong tool? I bought this and love it! It fixes iPhones, has a flathead and philips bit with it as well!

  • Need to do some prying for phones or laptop screens? This is the perfect tool for it! bends when it needs to, but doesn't lose its form or shape!

  • Drop a screw or need to do some fine tuning? Perfect! These tweezers are amazing and I would recommend them to anyone, including you.

    I also bought a 128GB flash drive to keep some common repair program on and it has saved me a lot of time and trouble.

    Put it all in a small backpack and you have a nice repair kit on the go!


    edit/

    Software! I use these weekly and it saves me a lot of time and trouble. I am open to suggestions on what you can also use, and would recommend using google for tutorials if you need help :)


  • Seagate File Recovery Have missing files or wiped a hard drive that you weren't suppose to? Use this to recover those files.

  • SeaGate Discwizard Need to clone a drive, format or mount an image? This is the tool for you! Simply download and you're on your way!

  • Malwarebytes Need to remove a virus, spyware or adware from a computer? Here you go! Simply run it (quick scan and full scan do the same thing!) and you'll be able to remove those violations after.

  • CCleaner A system cleaner all in one. I wouldn't recommend using the registry cleaner as it shouldn't do too much, but this is a streamlined way to remove all app data and computer files in one swipe.

  • BitDefender Free I don't use antivirus on my personal computer/devices, but I do install this on my customers computers. Easy to manage and low interference, makes it the perfect solution for those who don't know much about computers.

  • Hirens Boot CD This is an amazing tool that has endless capabilities. Forgot a windows password? No problem! Google guides for this to use it fully :)

    edit//

    If anyone else has suggestions on programs/tools to use i'm all ears. I've been doing repairs for the past 6-10 years (personally and for business) and these are the best things i've found so far. You can never have too much info/tools though :)

    And make sure you upvote everyone else who is giving you ideas/suggestions. A community that grows together knows more :)
u/Spirko · 15 pointsr/Justrolledintotheshop

Unfortunately, when you order them, you get a message: "The system says they're in stock, but we can't seem to find any, so they're on backorder."

u/Soulshine1978 · 14 pointsr/beachcombing

These, the rounded hook worked the best. After letting them soak in bleach water I used that one to go underneath or the middle and pluck them off. Not easy and is a long process, but worth it at least for me. Lol

TEKTON 6943 Precision Pick and Hook Set, 4-Piece https://www.amazon.com/dp/B000NPPBQK/ref=cm_sw_r_cp_api_i_MgPLDbBANYS6Y

u/LtStud · 13 pointsr/EscapefromTarkov

I’m waiting for BSG to add this baby to EFT. Gerber Ding-Dong Breaching Tool https://www.amazon.com/dp/B00KYO6BXM/ref=cm_sw_r_cp_api_BjHEAb5NG9JQ5

u/inibrius · 12 pointsr/fixit

I used this and it worked great. You shoot the screws in from the top and the little tripod thing breaks them off under the floor level.

u/NoCleverNickname · 10 pointsr/woodworking

It's a deburring tool. Good for cleaning up any sharp leftovers from milling, like around freshly drilled holes, pipes cut with a hacksaw, and whatnot.

u/DivergingApproach · 10 pointsr/ProtectAndServe

Better bring your Ding Dong too.

u/Ordinate1 · 10 pointsr/Tools
u/JosHensonGric · 10 pointsr/elementaryos

Definitely - though I can literally take 0 credit for coming up with anything myself....but I am happy to write a quick summary here with the relevant links that helped me out and then if people want something more formal I can do that somewhere too and hopefully u/MrChromeBox will be kind enough to link to it on his site.

​

so here goes

​

Step 1: Drink a beer or two

You need some steady hands for this but also need to give yourself some confidence before potentially destroying your beautiful £1000 glorified web browser....

​

Step 2: Make sure you have the right tools for the job

​

Specifically you will need:

​

- 2 USB C / USB 2/3 Flash drive (or an adaptor plus 2 flash drives)

- something like the basic tool kit from iFixit

- BUT you will also need a stupid T3 Torx screwdriver for 3 of the screws which isn't included, still it is cheaper just to buy that seperately rather than spring for the full 'ultimate repair kit' from iFixit

​

Here are the links for what you need on amazon:

​

Basic iFixit kit: https://www.amazon.co.uk/dp/B01MRNIFR6/ref=cm_sw_r_tw_dp_U_x_0fV5BbX0RZQS4

T3 Torx Screwdriver

https://www.amazon.co.uk/dp/B013703EG6/ref=cm_sw_r_tw_dp_U_x_CjV5Bb0ZWXH04

​

Or this kit actually probably has everythign you need, the ifixit one just has a few nice extras for any future repaires

https://www.amazon.co.uk/dp/B00445Y48G/ref=cm_sw_r_tw_dp_U_x_WiV5Bb3S6AT6

​

Flash Drives

- You need two flash drives, 1 for the elementary os iso to install on the pixelbook at the end and a second one for when you use the awesome UEFI firmware developed by u/MrChromeBox to backup your chromeOS in case everything goes to shit...

​

You may be able to use regular USB 2/3 flash drives with a USB C adaptor, but in my opinon since the Pixelbook only has USB C ports, you might as well invest in dual USB C / USB 2/3 drive now as you will end up needing it at some point (I used this for the elementary OS iso and a regular USB flash drive with an adaptor for the firmware backup)

Amazon links:

​

- USB C/USB 3.0 Flash drive:

https://www.amazon.co.uk/dp/B07H24MCRQ/ref=cm_sw_r_tw_dp_U_x_etV5Bb6JP78KC

​

-USB C / USB 2/3 Adaptor

https://www.amazon.co.uk/dp/B015Z7XE0A/ref=cm_sw_r_tw_dp_U_x_muV5Bb0Z1KDDQ

​

Step 3: Download Elementary OS Juno and donate some money to the developers

You can get the iso from www.elementary.io and if you don't know how to flash it to one of the flash drives mentioned above, you should probably stop now - but there are instructions on the website and Etcher is a good cross platform tool for the job (www.etcher.io)

​

Step 4: Pray to the linux gods, drink a beer and back up any data you care about on your pixelbook

​

Step 5: Put your pixelbook into developer mode (fairly safe)

Again, I can't take credit for this but there are great instructions for how to do this on https://mrchromebox.tech/#devmode

​

Enabling Developer Mode


>Entering Developer Mode requires you to first boot into Recovery Mode. For Chromebooks, this means pressing [ESC+Refresh+Power];
>
> Once at the recovery screen, press [CTRL+D] to enable developer mode, then confirm when prompted. As a security measure, transitioning to/from Developer Mode will wipe out all ChromeOS user data, essentially powerwashing (resetting) the device.
>
>Exiting Developer Mode is as simple as following the instructions on the Developer Mode boot screen (usually pressing [SPACE]), but may require resetting the firmware boot flags if you've changed them. As with entering developer mode, exiting will wipe all ChromeOS user data, so if you plan on keeping your device in developer mode, it's a good idea to set the firmware boot flags to prevent accidental exiting and loss of data.

​

​

u/mithikx · 7 pointsr/pcmasterrace

You're not the first, nor will you be the last.
Desperate times calls for desperate measures.

Just be sure to debur (or use a metal file) or tape up the edges or you'll cut yourself on those sharp edges next time you have to mess with your computer.

u/IndexFundSupreme · 7 pointsr/AskNYC

https://www.amazon.com/OBERRY-ENTERPRISES-3233-SQUEEEEEK-REPAIR/dp/B0006IK8YE

There is a This Old Home episode on YouTube showing you how to use it on hardwood floors

u/lepfrog · 7 pointsr/Tools

I personally prefer the griplock style jaws. if i was only buying one set it would be these. but tbh I kindof hate the groovelock style adjustment after using the button lock type. you don't have to spend knipex money to get this style as irwin "groovelock" pliers are decent quality and have the button lock. I own the knipex cobras, the irwins, and the channelocks and would rate them in that order just because I like the button lock more than the groove lock adjustment(to be fair the channelock brand is much higher quality steel than the irwins and will last longer). one other thing to consider is the Craftsman 9-45433 pliers set as they are just re-branded knipex cobras and I have seen them on sale b4 for about $30 (cammelcammelcammel shows they were $27.61 in may of 2017 on amazon)

u/ParksVSII · 6 pointsr/Plumbing

i use one of these for everything.

u/kowalski71 · 6 pointsr/LifeProTips
u/CuedUp · 6 pointsr/battlestations

They're homemade. Copy/paste from elsewhere:

Item|Quantity|Price
:----|:----|:----
100ft Paracord | 3 | $8 @ Army Surplus store (linked to Amazon)
Molex Extraction Kit | 1 | $15.95 @ Amazon
18-Gauge Wire, 100ft. | 1 | $11.36 @ Amazon
Molex Crimping Tool | 1 | $24.99 @ FrozenCPU
ConnectRight 24-Pin Female ATX Power Connector - Black | 1 | $1.50 @ FrozenCpu
ConnectRight ATX / PCI / EPS Connector Pins - Female - 4 Pack | 20 | $0.20 @ FrozenCpu
ConnectRight 8-pin 12V EPS Power Connector - Black | 3 | $1.00 @ FrozenCpu
ConnectRight 8-pin Female PCI-Express Power Connector - Black | 5 | $1.00 @ FrozenCpu
ConnectRight 6-pin Female PCI-Express Power Connector "Version 2" - Black | 1 | $1.00 @ FrozenCpu
ConnectRight DIY SATA EZ Crimp Connector - Black - 90° (Pass Thru Cap) | 8 | $1.25 @ FrozenCpu
ConnectRight DIY SATA EZ Crimp Connector - Black - 90° (End Cap) | 2 | $1.25 @ FrozenCpu

I unfortunately don't have any build pictures of the cables' construction. First off, it obviously really helps if you have a modular PSU. Mine was, with the exception of the mobo cables. My next build will be fully modular, because I'm not totally happy with how the 24-pin looks at the base. I used this guide and this guide for tips and help buying my supplies.

u/ChongGrow · 6 pointsr/Tools

EDIT: Klein has a lifetime warranty. Take those dykes to Home Depot and exchange them.

Looks like you have Klein's cheapest model of dykes. These dykes are for COPPER ONLY. As such, these dykes often come in apprentice packs that work out to about $12 a tool.

Sets like this:

https://www.amazon.com/Apprentice-Professionals-Klein-Tools-92906/dp/B004EKONLY/ref=pd_sbs_469_22?_encoding=UTF8&pd_rd_i=B004EKONLY&pd_rd_r=614MR61121B3HCN1PZD5&pd_rd_w=VVUEB&pd_rd_wg=4xZ76&psc=1&refRID=614MR61121B3HCN1PZD5

Professional grade dykes can be had from both Klein:

https://www.amazon.com/dp/B0000302WZ/ref=emc_b_5_i

And Knipex:

https://www.amazon.com/Knipex-7401200SBA-Leverage-Diagonal-Cutters/dp/B000X4OFUE/ref=sr_1_3?ie=UTF8&qid=1525112679&sr=8-3&keywords=Knipex+diagonal

u/eibv · 6 pointsr/Rainbow6

Actual breaching hammers are usually between pretty expensive and more than just a common hardware store item. Sledges seems to be based on the far cheaper Gerber one though.

u/VivisClone · 6 pointsr/techsupport

Actually just bought this: http://www.amazon.com/TEKTON-28301-Everybit-Electronics-Precision/dp/B00VJYWRKW

A few Months ago. It's been a godsend to own.


Is Hitman PRO a constant scan then?
Cause I was thinking I'll just keep Combofix and Tron Script on me to get rid of Virus and Malignant Stuff

u/ahyokata · 5 pointsr/Justrolledintotheshop

I dont know if I would use an impact gun for that, I much prefer this

u/SailAgainSomeday · 5 pointsr/DeadBedrooms

Don't fight over any of it. Your freedom is worth 10 snowblowers. Your happiness is worth a dozen tool sets, but, this is a kit I got my wife a few years back. I NEVER use it, so she ALWAYS has what she needs - it's a great start!

https://www.amazon.com/Stanley-94-248-65-Piece-Homeowners-Tool/dp/B000UHMITE/ref=sr_1_3?ie=UTF8&qid=1494875518&sr=8-3&keywords=tool+kit

u/r1otctrl · 5 pointsr/mobilerepair

Sounds like you hit a snag... Nothing really to worry about if you werent sticking your head in the bag with the punctured battery.

Was this an OEM battery that was being replaced from the i6 or was it 3rd Party? When we remove batteries that have gone bad or already in the death/swollen stage they start to smell very sweet, kinda fruity if you want to put a flavor to it.

Once it has gone to that point I would hesitate using anything sharp near the damn thing.

Tip to removing the Magic tape from iPhones
--------------------------------------------------------------
If the iphone still has the original tape on the battery....
--------------------------------------------------------------

  • Using a pair of either fine tip or rounded edge tweezers
  • Get a good grip on the black tab
  • Start to rotate the Tweezers towards the battery so the white tape coils around the tip.
  • Do not pull it towards you too quickly or else the tape will snap and it just makes the removal that much more a pain in the ass.

    If done properly, you should be able to remove both strips within 40 seconds. (or less).

    now....
    --------------------------------------------------------------
    If you DUN GOOFED and the tape is UNDER the battery....
    --------------------------------------------------------------
  • If you were to break both strips and they're all the way on the bottom, I would use an iSesamo to slowly scrape the bottm layer of the adhesive, while trying to lift the battery to be able to grab the tape again.

    hope it helps and you shouldn't need the fear of contracting popcorn lung.
u/takes_joke_literally · 5 pointsr/rccars

RE: RC specific tools: get this https://www.amazon.com/Kinexsis-Ultimate-Surface-Startup-Tool/dp/B017CIT05I/

It's totally worth the $22. Don't do what I did, and bargain shop.
This has everything you need and is the standard by all the RC guys I know.

u/Zyzan · 5 pointsr/techsupport

From the information provided, we can probably get you out of this mostly unscathed. For starters, I don't think you have to worry about any damage to the internal components. The keyboard on the Yoga 920 has precisely one trillion screws affixing it to the chassis, and the gaps which could lead to the motherboard are minimal. That being said, there is still a pretty good chance that your keyboard is fugged. There is a very small chance that one of the fans needs cleaning as well.


So we have two options here:

  1. yolo and turn the thing on after letting it sit for a good chunk of time so that maybe any water inside dries and doesn't short the motherboard when you turn it back on. Then try the keyboard to see if it's working.

  2. preemptively take the notebook apart (this is not as scary as it sounds - computers are essentially just adult legos) and let it air dry, which will let you manually inspect the motherboard for any spillage and clean it. This is also a good opportunity to check the fan and do any cleaning that needs to be done. Once you're confident that everything is dry, reassemble it, boot it up, and test the keyboard.


    If the keyboard doesn't work, you'll have to take the laptop apart (or take it apart again, if you already did it in step 2, and replace the keyboard.

    I highly recommend getting this iFixit kit if you're going to take the notebook apart.

    https://www.amazon.com/iFixit-Essential-Electronics-Toolkit-Do-everything/dp/B01MRNIFR6/ref=pd_sbs_469_t_1/141-5166025-6730510?_encoding=UTF8&pd_rd_i=B01MRNIFR6&pd_rd_r=83be4ca4-5d0d-4d14-a9f2-9670777f914f&pd_rd_w=ytM6H&pd_rd_wg=kOteO&pf_rd_p=5cfcfe89-300f-47d2-b1ad-a4e27203a02a&pf_rd_r=QRPD39WM0Q9M4DKW7MC6&psc=1&refRID=QRPD39WM0Q9M4DKW7MC6

    As for disassembling the laptop, this is a pretty good guide on this exact model:

    https://www.laptopmain.com/lenovo-yoga-920-disassembly-ssd-ram-upgrade-options/

    And here is a replacement keyboard:

    https://www.amazon.com/Laptop-Replacement-Keyboard-920-13IKB-Backlight/dp/B07MNBZ3C6
u/ShortWoman · 4 pointsr/RealEstate

Do not bother getting copies of the old keys made. Plan on rekeying or replacing the locks the day you close. Even good people sometimes lose keys or lend one to somebody they shouldn't.

This brings me to the other must have: a basic tool set and one of those big books of home repairs. You may well eventually want to get a cordless drill/screwdriver; you'll be shocked how handy one can be.

u/hnocturna · 4 pointsr/Android

If you're adventurous/fed-up, you can do the repair yourself pretty easily. It will probably take less than 15min from start to finish and about $30 in supplies.

You can check out someone going through the same procedure here.

USB Charging Port for Sprint

Tools

Super easy and doesn't really require any amount of real technical skill. If it ever breaks again, it's only like $18 for the actual port since you don't need to buy the tools again.

Probably not the easiest solution, but probably the cleanest and it will also allow you to connect your phone to a computer again if you need it.

u/headmustard · 4 pointsr/flying

Not sure if you're joking with all that tech or what.

  • Tire tubes for both the mains and nose.
  • A bottle jack and jack pad (if applicable) for lifting a gear leg.
  • spark plugs and plug wrenches.
  • various cowling screws and other AN hardware.
  • All airframe-specific hand tools your plane may require and a set of normie tools like this
  • https://www.amazon.com/gp/product/B009EMKMCG
  • oil and a funnel
  • rags
  • survival rifle (one of those .22/.410 thingies)
u/mqandeel · 4 pointsr/Nexus6P
  1. Feb 2018
  2. https://www.amazon.com/gp/product/B076ZMV7MD/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
  3. Tools with battery wasn't enough, got a Precision Knife and other tools to complete the operation.
  4. Hardest part is to remove the Glass from the Top of the back.
  5. Very good, 3.5 SOT with 30% left at the end of the day.
  6. ...
  7. Battery replacement worths it, but Get a better tools, currently I've ordered iFixit Toolskit https://www.amazon.com/iFixit-IF145-348-2-Essential-Electronics-Toolkit/dp/B01MRNIFR6/ref=sr_1_fkmr0_1?s=wireless&ie=UTF8&qid=1523034494&sr=8-1-fkmr0&keywords=ifixit+essential+kit. Hopefully it will be useful.
u/82ndAbnVet · 3 pointsr/gifs

I watched the product video and dude, I am so buying this kit. Already found it on Amazon and put it in my cart

O'BERRY ENTERPRISES 3233 "SQUEEEEEK NO MORE" FLOOR REPAIR KIT https://www.amazon.com/dp/B0006IK8YE/ref=cm_sw_r_cp_api_Q.H0Ab6ZFFDHY

u/1new_username · 3 pointsr/HomeImprovement

Here are things from my wishlist (past and present)

Wera Screwdrivers
https://smile.amazon.com/dp/B0085NTQJK/

Oscillating blade set:
https://smile.amazon.com/dp/B0109SELWA/

Clamp multimeter:
https://smile.amazon.com/dp/B00NWGZ4XC/

Kreg Jig Jr.:
https://smile.amazon.com/dp/B000J43A7W/

Angled Long Nose Pliers:
https://smile.amazon.com/dp/B00N3VSS4S/

Groove Lock Pliers:
https://smile.amazon.com/dp/B000FK1R0W/

11 ft wifi endoscope:
https://smile.amazon.com/dp/B01MYTHWK4/

non contact voltage tester:
https://smile.amazon.com/dp/B001UAHZAM/

claw nail puller:
https://smile.amazon.com/dp/B0015YPJMY/

Workmate portable work bench:
https://smile.amazon.com/dp/B000077CQ0/

Cable snake fish tape:
https://smile.amazon.com/dp/B000BP7WBO/

9 Outlet metal power bar:
https://smile.amazon.com/dp/B00F8ZQY5M/

Spade drill bit set:
https://smile.amazon.com/dp/B00099E7WE/

36" bubble level:
https://smile.amazon.com/dp/B000UKMWMO/

u/blackrs17 · 3 pointsr/FocusRS

Use a pick set. I got a set at Northern Tool after tearing my car apart and getting to a point where I was so frustrated I almost just gave up and put it all back, but asked around in my local ST/RS Facebook group for ideas on how to remove the damn clip.

https://www.amazon.com/dp/B000NPPBQK/ref=cm_sw_r_cp_apa_i_MmJkDb8YT215N

I also couldn't remove the idiotic, corroded Torx bolt holding on the heat shield, so just wound up bending it back as far as I could.

Finally was able to pry off the clip whilst tearing up my hand a ton, but totally lost the clip. Make absolutely sure you don't do that.

They don't just sell the replacement from Ford as it's considered a part of the entire turbo assembly, and other parts you'll find when Googling aren't a fit. I'm currently running the TurboSmart WGA without the clip and it's been fine for about 4 months (since there's so much tension on it from the actuator arm), but sometimes I worry the arm will slip off, and the process to fix WON'T be fun.

Hope this helps.

u/flashinfected · 3 pointsr/Reprap

In addition to flush cutters, I've found a few different types of picks help to clear out hard to reach support areas, and fastener holes. Just don't punture your finger!

https://www.amazon.com/TEKTON-6943-Precision-Pick-4-Piece/dp/B000NPPBQK

u/frankzzz · 3 pointsr/Tools
u/chrisbrl88 · 3 pointsr/HomeImprovement

Glad you solved it. For future reference, a set of picks is one of those things that should be in everyone's toolbox.

u/EraserGirl · 3 pointsr/LivingAlone

Sturdy step stool ($40) - not the rickety tubular kitchen chair ones, I mean one where you can stand on the top. a Buy it for Life item, not inexpensive, but safe. https://www.amazon.com/Louisville-Ladder-AS3002-6966014-2-Foot/dp/B00182TWL2

Leatherman multi tool (around $50), which i keep in the junk bowl because I can never find a screwdriver fast enough. Pricey new, less expensive when you buy it second hand or in a pawn shop. they don't really break, but you do have to clean and oil them once a year. https://www.amazon.com/LEATHERMAN-Wingman-Multitool-Stainless-Steel/dp/B005DI0XM4/

Cordless drill (under $50), mine basically has the screw driver bit in it 90% of the time. the rest of the time I drill lots of pilot holes. pay attention to the battery... if you can get one with a battery that is shared by other tools in the line, then it is easily replaceable and if you buy another tool in that line you can swap batteries. I like to have 1 battery in the charger and one in the device. https://www.amazon.com/BLACK-DECKER-Cordless-Driver-BDCDD12C/dp/B0111N8L7I/

Spirit, bubble or torpedo level. (under $10) the Hanging kit usually contains just the wires and hooks, but you need a small spirit level for hanging pictures and shelves evenly. doesn't matter the brand they all work the same https://www.amazon.com/WilFiks-Leveling-Resistant-Different-Visibility/dp/B07M62GJYP/

Small tool boxes vary in quality. I don't know if this is for you or someone else. But don't buy anything unless it's a NAME BRAND, cheap metal tools bend and can break with too much torque. Even the Stanley line that Walmart sells isn't fabulous, but it's better than a nameless brand. I don't like SETS of tools, but you need to start someplace, buy GOOD tools one at a time, I love finding $$$ tools at thrift stores. https://www.amazon.com/STANLEY-94-248-Piece-Homeowners-Tool/dp/B000UHMITE/(i bought a cheap socket set 4 years ago to replace my stolen ones and they already have rust)

Bucket organizer. (around $15) If you buy a SET of tools, take the plastic blow molded container and put it in the recycling. You will never bother putting the tools back in and when you get more tools they won't fit. Bucket Organizers are pockets that fit around a 5 gallon bucket. You shove your tools into the pockets and everything else in the middle. And keep it in the bottom of your closet and carry it to where you need the tools. https://www.amazon.com/Bucket-Boss-10030-Bucketeer-BTO/dp/B00GK4TOWK

Tack Hammer. (under $15) You won't need a big 22 oz hammer, but a smaller 16 oz one with a normal handled and then a Tack hammer, these have a narrow head and sometimes are magnetic and hold the nail in place. Tack hammers are easier to use for hanging things exactly where you want them. https://www.amazon.com/Stanley-54-304-5-Ounce-Magnetic-Hammer/dp/B00002X1XD

Stud finder.(under $20) uses a battery, and lets you know where the studs are behind drywall. BEST PURCHASE EVER. https://www.amazon.com/Upgraded-Stud-Finder-Wall-Detector/dp/B07VLDTVFQ/ any brand will work fine.

Digital Infared Thermometer (under $20) Non-contact Digital Laser Infrared Thermometer Temperature Gun - ALSO BEST PURCHASE EVER... works in the kitchen for food and oven temp, fridge temp, and for locating drafts and cold spots around doors and windows. https://www.amazon.com/Etekcity-Lasergrip-1080-Non-Contact-Thermometer/dp/B00DMI632G

Toilet Plunger - the sort with the extra bit on the end. https://www.amazon.com/Get-Bats-Out-Plunger-Bathroom/dp/B00ODD5MD0 you do NOT want to be waiting around for someone to unblock your toilet. It may be disgusting but scoop out some of what's in the toilet before you start plunging, it's less disgusting than having to mop it off the floor. You want the plunger that makes a seal around the bottom.

BUCKET. (under $10) mine is constantly in use, i keep it in the tub and toss wet things into it. I have gone through EVERY TYPE on offer...I was so sick of plastic buckets, that warped and stained, where the handles ripped out. But the BEST and cheapest one I have ever found is a flat back duraflex bucket for watering horses. Not kidding. Made of a hard polyethylene these things are designed to be flung around and stepped on by 2000 lb animals. https://www.amazon.com/LITTLE-GIANT-Flat-Back-Dura-Flex-Plastic/dp/B000HHLHPS/ these are cheap if you buy them in a feed store, but even with the shipping on Amazon it is WELL WORTH the money. You will need a bucket when you empty the back of the toilet tank to change the flushing flapper or gasket, and you will need it when you empty the commode itself, if you have to change out the wax seal underneath.

Blanket hangers. (6 for $27) yeah this is obscure, but when I moved I lost a LOT of storage space. These saved my sanity. I use them to hang up quilts and sleeping bags in the back of the closet OFF SEASON. I also use them to hang blankets, sheets curtains and stuff once they come out of the laundry aren't quite dry. I didn't even know there was such a thing before now I wouldn't give them up. https://www.amazon.com/Stock-Your-Home-Comforter-Organization/dp/B00EUG51JU

Flashlight. ($30-50) I've written about these before. Until I bought a GOOD one, I had no idea how bad the others were. Cheap flashlights are great to have scattered about in the cellar, or in the junk drawer. but if you really want TO SEE, get a great flashlight. I gifted myself one for christmas one year and I love it. It hangs by the door and if I am going to be out very late or the weather is bad, I shove it in my bag. It will also illuminate Well past the end of the porch and into the yard if I hear a noise. https://www.amazon.com/Pelican-Carded-SabreLite-Flashlight-Yellow/dp/B01CKAIYV4 any very good brand will do, but I found Maglites to be dangerously useless.

u/scottocs · 3 pointsr/Chattanooga

Go the speed limit in the right lane, not the left lane (on highways only). The left lane is for passing cars going slow in the right lane. People WILL tail you and honk at you if you are going slow in the left lane when you have room to get over in the right lane.

If something happens to your car, you should try doing your own research first. Google the model and make and the problem. Sometimes it will be a common problem among your type of car, and it will possibly be an easy fix. Also, try to make some friends who know at least a little a bit about cars. Make sure to check your oil regularly and check your tire pressure and life. Don't buy replacement parts from a dealership if you can avoid it. Salvage yards are cheap and will get any part you need for your car, even if it's a cracked piece of plastic you want to replace.

A general tool set will work for now until more complicated things come around. If you plan on buying something non-grocery related, check to see if it's cheaper on Amazon. Many times it is. Here's the #1 tool set on Amazon.

Message me if you have questions or problems. I'm a pretty good handyman.

u/cornfedandconfused · 3 pointsr/Tools
u/Zatoichi392 · 3 pointsr/mechanics

Sunex makes a nice little bit set that comes with a driver and extension in a slick little case. usually find them on the truck or...

https://www.amazon.com/gp/aw/d/B000XW4C8Q/ref=mp_s_a_1_1?ie=UTF8&qid=1478742544&sr=8-1&pi=AC_SX236_SY340_QL65&keywords=sunex+bit+set

That.

Edit: Autocorrect!

u/cheese61292 · 3 pointsr/Gunpla

Tamiya Masking Tape is your best option. Liquid Masking solutions don't always work well.

I would also get a nylon spudger:
http://www.amazon.com/dp/B001DD1UJS

The nylon is soft enough to not rip up the masking tape but hard enough to press it down into the groves of pieces to make sure you get good protection.

u/goodguydan · 3 pointsr/Gunpla

Buy a spudger, it's one of the best tools you can find when it comes to pulling your kits apart.

http://www.amazon.com/3M-SP3010-Nylon-Spudger-Tool/dp/B001DD1UJS/ref=sr_1_2?ie=UTF8&qid=1334026158&sr=8-2

u/Lorithad · 3 pointsr/pcmasterrace

Not so big of a deal with leaving oil. Bigger potential problem is a static shock. When dealing with the internal components of a computer, it is recommended to wear something like this.

It'll ground you out so you don't accidentally destroy things.

u/GenoOfMemphis · 3 pointsr/electricians

Klein Tools 92906 ProPack 6 Apprentice Tool Set for Trade Professionals (6-Piece) https://www.amazon.com/dp/B004EKONLY/ref=cm_sw_r_cp_api_Qm5EAbQVA3JFH

That’s a good deal. It has lineman pliers, diagonal cutters, needle nose, wire strippers, and flat/ Phillips screwdrivers.

Screwdriver and Nut Driver 11-in-1 Multi Tool, Cushion Grip Handle, Industrial Strength Bits Klein Tools 32500 https://www.amazon.com/dp/B0015SBILG/ref=cm_sw_r_cp_api_yp5EAbSKE4D2A

This is a good all purpose screwdriver to carry around

Klein Tools NCVT-2 Dual Range Non-Contact Voltage Tester https://www.amazon.com/dp/B004FXJOQO/ref=cm_sw_r_cp_api_qq5EAbTTZ8GYW

This is a non contact voltage tester and it might just save you some pain/your life

Channellock 440 12-Inch Tongue and Groove Plier https://www.amazon.com/dp/B00004SBCU/ref=cm_sw_r_cp_api_xr5EAbWNKDP5C

You should probably get 2 pairs of these. It’ll help you twist on couplings and stuff

Stanley 33-725 25-Feet FatMax Tape Measure https://www.amazon.com/dp/B00002PV66/ref=cm_sw_r_cp_api_Xs5EAbGVWXZDV

A lot of people like these tape measures for their larger claws

Klein Tools 98002BT Bottle Opener https://www.amazon.com/dp/B00093GENU/ref=cm_sw_r_cp_api_4u5EAb52FZ742

This will help for when you go home


u/Reygle · 3 pointsr/techsupport

If it has a removable battery, pop it out and look for more screws under. When you're pretty sure you have all of the screws out, use a very, VERY thin flat blade or a spudger to pry the lower housing free. There will likely be clips every inch or two around the edges.

Also check Youtube, lots of people make disassembly guides for laptops.

u/bsrieger · 3 pointsr/HomeImprovement

I have this set and it's fantastic price:quality. As far as non-power tools go, this covers pretty much everything I need around the house and working on my cars, except for a hammer and wonder bar. I think I remember buying it at Menards for $50 on sale.

I'm a huge fan of Hitachi power tools. Excellent quality for very reasonable price. Lifetime warranty. The 18v drill/impact combo is like $115 on Amazon.

The biggest helper of all the tools I own is the oscillating tool. I have this Porter Cable model that has served me veyr well, but ANY oscillating tool will do. Uses include: scraping up stuff like old stick-down tile (with a scraper blade), cutting holes in things like drywall where a utility knife would be a lot of work, removing old caulking (scraper blade again), small cuts on things like trim, sanding into corners (such as when refinishing a hardwood floor), and the list is basically infinite in my mind.

Other handy homeowner power tools include (in order of my preference) an air compressor, angle grinder (be safe with it!), bench grinder (sharpen your own mower blades, etc), reciprocating saw, and circular saw. The last two are more useful if you're doing more DIY projects but the others are really handy to have all the time.

u/lolcorndog · 3 pointsr/liveaboard

is it the pop top model ? Internet can come from your wireless carrier, a dock side phone outlet, or a boosted antenna from a shoreside access point.

I have lived on several different boats, but the best thing I can say is :

  • bring your changes of clothing and your laptop. That's all you need. Put everything else into a storage unit or get rid of it.

  • If the boat is an 80's model, you may have second thoughts about drinking out of a 40 year old water tank. But a 5 gallon water jug and find a place to keep it on the boat.

  • You will have 30 amp service. Use it all. Don't worry about solar this and that - it's expensive and you don't need it. The electricity however is very useful.

    • Buy an electric kettle. I go through 3 pots of hot water when it's time to do dishes. It's great for instant coffee and tea. Also for other cleaning.

    • Buy a fan. Not too big or small, one that oscillates. This is half your air conditioning.

    • Buy a forced air heater. Other kinds are good, but the forced air one is best for you. Let it run constantly, it good to prevent mold.

    • Buy a light. The clamp on kind. This will provide good light for reading, working, and doing whatever.

    • Buy an electric hot plate for cooking. I purchased an induction model and it works great, just need special cookwear, which I bought especially for it.

      Now at this point, since you are living aboard, I would say buy a refrigerator, microwave, and toaster oven. But in a 25' boat I suppose this may be excessive. Also depends on what you cook and how you want to approach it. If you don't have a fridge I guess you aren't cooking for several days in advance, and you are just eating as you go nightly. Alright plan, but I would rather put the fridge on deck and secure it there. -

  • I realize you are talking about racing, but I would think you could race on other boats first. It's tempting to have a 25' liveaboard / blue water racer / apocalypse survivor boat, but realistically I would focus on being a liveaboard. You sailing neighbors may make fun of you for that though.

  • Throw away all the tools you find on the boat and buy one of those toolsets that come in a plastic molded case.

    http://www.amazon.com/gp/product/B00F4AVRGW?keywords=crescent%20tool%20set&qid=1457211905&ref_=sr_1_1&sr=8-1

    Of course you still need a hammer, a voltmeter, etc. But having a complete, all there set of tools is the difference between fixing a problem and putting it off for another time.

  • Keep it minimalistic. The less you have the better. Like I mentioned earlier. Don't buy a coffee maker, it's just more clutter. Use instant or some other method. I use a coffee press when I want to be fancy.

  • use your boat and keep it in usable condition. Once the potted plants appear on deck, it's another story.

  • An electric dehumidifier goes a long way to making a boat more liveable.. Only works when you keep the door closed all the time.

    I think the biggest issue when living aboard is making a vehicle that was meant for weekend use into one for full time use. Different usage demands require different solutions. For example the 25' is tool small to shower in, and would likely create a real mess. You don't want your bilge filling with nasty smelly shower water in any case, right ? Can you imagine the smell on a hot summer day of all that accumulated gray water residue ? So look to a gym for that service.

    I have to say that as far as sailboats go, I really like the boom-tent. It looks so nice on a rainy day with the entry hatch open.
u/MisunderstoodDemon · 3 pointsr/mallninjashit

Kind of expensive for a prybar with a sledge head on it Gerber Ding-Dong Breaching Tool [30-000790] https://www.amazon.com/dp/B00KYO6BXM/ref=cm_sw_r_cp_apa_Mq5bzb2841ZMN


Edit* Fro hammering!? Freudian slip perhaps...?

u/tr1ppn · 3 pointsr/computertechs

I know you already got the iFixit kit (and now I want that too), but this is a good "pocket" toolkit.

Tekton

u/SoCaLLbeer · 3 pointsr/rccars

If you want a budget set you can keep in your pit/travel stuff this one is not bad. I built my B6.1d with it and use it at the track on both my cars. Only bad thing is the edges on the handle can be sharp if you use it with the bits out. Not perfect but for the price it is a good kit. Once the tips wear out on mine, I will just wrap the handle on it and use it as a nut driver. https://www.amazon.com/Kinexsis-Ultimate-Surface-Startup-Tool/dp/B017CIT05I/ref=sr_1_3?ie=UTF8&qid=1550537111&sr=8-3&keywords=RC+tool+kit

u/not_a__rapist · 3 pointsr/mobilerepair

I fix nearly 90 iPhones a month, and so far the ifixit kit is the best .... no stripping and magnetic makes my life easy

iFixit Essential Electronics Toolkit - Your Economical Do-everything Toolkit https://www.amazon.com/dp/B01MRNIFR6/ref=cm_sw_r_cp_api_i_bBBYCb3YFJVG4

u/itzaklevi · 2 pointsr/metalworking

I don't think so, really. It is essentially just a pivoting curved, sharp knife. Think of it as creating a very small chamfer on the edge. Plus, it is a lot harder to slip up and really mess up the other side.

Looking at /u/supertroop 's post, the thing I am thinking if is different. Here's what I am think of. I think the one above does both sides at once.

u/THE_CENTURION · 2 pointsr/CNC

I'm a fan of this one from General. It's got a nice solid aluminum handle. I can't stand the ones with the extra cutters rattling around inside. I mean, you have a toolbox you can store those in.

u/zeroly32 · 2 pointsr/motorcycles

I would cut a slot into it with a small cutting wheel using a dremel then hit it with a slotted screwdriver attachment on a hand impact I've used that method a few times on stuff like that...GLHF don't get frustrated and make it worse!!!! http://www.amazon.com/Lisle-29200-Hand-Impact-Tool/dp/B0002NYDRG

u/TomVa · 2 pointsr/woodworking

Before you go to crazy did you check the brushes?

This is from a random troubleshooting site.

4. Sparks and/or Smoke

All that brush bouncing on the armature will often kick up some sparks out the dust vents as the electricity arcs to stretch over the gaps of damaged areas. Eventually, if brushes are not replaced, they can continue to damage an armature and cause overheating or smoke.

As far as getting screws out they make an impact driver of sorts that you strike with a small hammer. The tool is set up that striking it causes it to turn because the turn it also insures that the head stays in the socket.

http://www.amazon.com/Lisle-29200-Hand-Impact-Tool/dp/B0002NYDRG/ref=sr_1_1?s=hi&ie=UTF8&qid=1427804244&sr=1-1&keywords=impact+screwdriver

u/aDDnTN · 2 pointsr/motorcycles

have you guys (paging /u/ConsectorVerum) heard of an hand impact tool/driver?

this is the tool you are missing that will prevent bolt heads from stripping out as you are backing them out.

https://www.amazon.com/gp/product/B0002NYDRG/ref=ox_sc_sfl_title_15?ie=UTF8&psc=1&smid=ATVPDKIKX0DER

this isn't the best or cheapest, it's just the one i have in my Amazon wish list.

u/SnakeJG · 2 pointsr/DIY

That appears very similar in function to the Stanley one I have. Although, mine has an LCD display instead of the three lights.

I've actually used it successfully to find not only studs, but also floor joists through carpet (to use something like this to greatly improve the floor squeak.)

u/DEADB33F · 2 pointsr/homeowners

Squeaky floorboards normally just mean that a few flooring nails have worked a bit loose. Cheapest option is usually just to roll up the carpet in the areas where the floor is squeaky and screw down the boards.

Alternatively get some of these special screws designed for just this job. They screw directly though the carpet and are then snapped off. (Here's a demo video)

the second option is far more expensive and finding where the rafters are is a bit of an art if you don't have a stud finder, but it's a good option if you're in a hurry or decide that pulling the carpets up is too much of a pain in the arse.

u/DaveTheFuturist · 2 pointsr/DIY

I've used this product before:

Squeeeeek No More Floor Repair Kit
http://www.amazon.com/OBERRY-ENTERPRISES-3233-SQUEEEEEK-REPAIR/dp/B0006IK8YE/ref=sr_1_1?ie=UTF8&qid=1405351948&sr=8-1&keywords=Squeeeeek+No+More+Floor+Repair+Kit

with great success. The bottom video here:
http://www.123itsdone.com/index.html

shows how it's done over vinyl.

There will be a small hole, inevitable with vinyl, but you might be able to find a strategic spot in the fake grout line, or pattern. But see the video first...

u/ZirkleBorklov · 2 pointsr/whatisthisthing

Yes, usually sold in sets with different angles/shapes at the tip.

u/A52-830 · 2 pointsr/Fixxit

if those are .110 connectors (hard to tell), there are flaps of metal holding the blades in the hood. i use a pick, like the straight one in this set: https://www.amazon.com/dp/B000NPPBQK

if you look at the second picture, it looks like you can see the flap down there on the left side of each connector blade. push on the wire from the back to slide the blade forward (hopefully unwedging the flap from being stuck against the hood), dig down with the pick, and try to push the flap back into the blade. then, while maintaining that pressure, pull back on the wire.

having three hands would be really useful for this, but it can be done. as it turns out, i spend all afternoon doing this trying to build a connection harness between the old bike and a new cluster i bought.

u/AAA515 · 2 pointsr/MechanicAdvice

Oooo I love tool shopping. So if I had to start over buying tools here's my list
Wrenches

1/2" sockets

3/8+1/4 sockets

Oil strap wrench

Pry bars with strike cap

1/2" impact

Pick set

Door upholstry remover

Stethoscope

Valve core tool

Electrical tool

Pliers: needle nose, long length needle nose, end nippers, diagonal cutters, tongue and groove, locking of all sizes and shapes

Lockable tool box, I like Husky Husky 2 electric boogaloo and HF cart don't forget to use the coupon!

u/translunar_injection · 2 pointsr/AskMen

Here it is. this would be a fine collection. Good brand too; certainly we have some of their tools in the family for a generation.

http://www.amazon.com/Stanley-94-248-65-Piece-Homeowners-Tool/dp/B000UHMITE/ref=sr_1_1?ie=UTF8&qid=1397574412&sr=8-1&keywords=tool+kit

u/shmashmorshman · 2 pointsr/HomeImprovement

Start with a basic tool kit: screwdriver set, hex wrenches, pliers, box cutter, level, hammer, ect.

https://www.amazon.com/Stanley-94-248-65-Piece-Homeowners-Tool/dp/B000UHMITE/ref=sr_1_3?ie=UTF8&qid=1495687960&sr=8-3&keywords=Tool+kit

Something like this.

Then i definitely recommend socket wrenches.

https://www.amazon.com/DEWALT-DWMT73804-Drive-Socket-Piece/dp/B00WLVV2YE/ref=sr_1_9?ie=UTF8&qid=1495688089&sr=8-9&keywords=socket+wrench

Next I'd recommend an impact driver. There are going to be times where your drill won't cut it.

https://www.amazon.com/BLACK-DECKER-BDCI20C-Lithium-Impact/dp/B00JJ3QY9A/ref=sr_1_4?s=power-hand-tools&ie=UTF8&qid=1495688152&sr=1-4&keywords=impact+driver

I purchased a circular saw recently and have gotten a good amount of use out of it. If you don't plan on doing any woodwork then pass on this.

https://www.amazon.com/Black-Decker-BDECS300C-Circular-Laser/dp/B01LX8KOAD/ref=sr_1_6?s=hi&ie=UTF8&qid=1495688185&sr=1-6&keywords=circular+saw

Probably outside of your price range if you're sticking to $300 but a pressure washer is amazing. I use mine all the time.

Another extra item would be an air compressor. You can use it for tons of stuff such as nail guns.

And then also you'll need all your yard work tools. Loppers, shovels, rakes, trimmers, ect.

Oh man.... All the stuff to maintain your home is so expensive. But I'd start here.

u/Astramancer_ · 2 pointsr/DIY

People own homes without knowing how to do shit all the time. It's fine. A willingness to learn is more important than a brain full of knowledge for your average homeowner.

In my opinion, short of taking a class at a place, the best way to learn is by doing.

Find a project that you want to do. Google and Youtube how to do it. Do it.

I have zero interest in automotive, but I have some interest in carpentry, so that's what I'll address.

Figure out something that you want but don't have. Start simple - rectangles and squares are easy to make. Maybe you'd like an end-table? Or a coffee table? Do you need a bookshelf? All of those are made using only rectangles and squares.

A surprising amount of home carpentry projects can be made with "Dimensional Lumber" aka "what you can buy a home depot" and a minimum amount of tools. Just be aware that a 2x4 isn't actually 2 inches by 4 inches when drawing up your plans! (and yes, you need to draw up your plans and develop a 'cut list' so you can get all the cutting out of the way before you start with assembly rather than jumping back and forth)

While things can be done with hand tools, if you have the capability of working outdoors or 'dirty' indoor spaces like a garage, I'd suggest getting at least a circular saw. They're relatively inexpensive and easy to use for short straight cuts - but be prepared to sacrifice a board or two to the learning gods. But if you're going to have to work indoors inside your living spaces, a tarp and hand saws can address 90% of the mess. Either way, though, get a decent drill and a bit set.

-----------------

The only real tools that I would say are 'must haves' before owning a home is a generic tool kit and a studfinder. There's lots of prebundled toolkits that have the basics. At the very least, make sure you want a hammer, a screwdriver with interchangeable bits, a set of allen wrenches (both metric and standard), a measuring tape (at least 10 feet long, but longer is better up to a point), a set of wrenches (ratchet is nice, but not alwyas needed), and a spirit level. Basically this but look around, there's lots of inexpensive but decent tool kits out there. Those will be the tools you need the most for non-specialized tasks. You won't be renovating a bathroom with it, but you can certainly install a new toiletpaper roll holder, tighten up a loose cabinet door, hang a picture, and assemble most anything that doesn't come with it's own tools with it.

Oh, and get 3-in-1 household oil. WD-40 isn't a long term lubricant.

u/CrazyIrina · 2 pointsr/AskWomen

I'm a believer in quality. All the stuff I have is going to last until the ends of the Earth.

Anyway...

You can get an All-In-One kit like Kobalt, or Stanley or Craftsman, but the quality doesn't seem there these days. They might be decent so long as you aren't trying to rebuild an aircraft carrier or something, though.

I'd look at this: https://www.amazon.com/Stanley-94-248-65-Piece-Homeowners-Tool/dp/B000UHMITE

Get the one with the screwdrivers and wrench. It's $57 for everything you'll likely need. My old Stanley stuff is okay, but I can't speak to the new stuff.

Another alternative is buying top quality individual tools and piecing together your own kit, but the prices can be steep.

I use Wera Kraftform Kompakt screwdriver. It has the bits in the handle. Usually, these are junk, but this one is very sturdy. Also, the shaft can be used in a drill. The bits are top quality and don't get spun out. $45.

You'll still want a regular set of screwdrivers because the one I mentioned earlier has a detach bit head and a short shank so it can't fit everywhere. Wera Classic 6-set $25.

For pliers, I get Channellock. They are also very sturdy and don't ruin bolt heads or make themselves hard to use from sloppy fit or slipping around. Crescent wrench $25. Regular pliers $11, needle nose pliers $17.

Plastic Stack On tool box $13. Total $136. Add a hammer and a tape rule and a small level for another $25 and you'll be set for a while. These tools will last forever. Also, a Makita cordless drill at some point. Mine is really powerful and fits my hand and was only $100.

u/N3twerx · 2 pointsr/maker

The basics! Multi-driver, channel locks, allen key set, and a utility knife. If you have a little more room then maybe a small socket set.

Something similar to this Stanley set would probably do you just fine. Although I'd probably go Klein's 11 in 1 for a multi-driver to consolidate. =)

u/bws311 · 2 pointsr/Random_Acts_Of_Amazon

1

3

4

5

6

7

8

9

10

11

12

13

14

15

16

17

19

20

bonus




Happy happy cake day And thank you!

u/_-__---_-__-__---__- · 2 pointsr/Tools

Buy a homeowner's tool kit, and dump it into a tool bag. That should get you started.

u/jackicks · 2 pointsr/Tools

I’ve had a great experience with Tekton tools. They make all kinds of stuff that doesn’t break the bank.

Here’s a few notable mentions that changed the game for me:

Sunex 9726 Mini Ratchet and Bit Set, 1/8-Inch - 1/4-Inch S2 Bits, 5/64-Inch - 1/4-Inch hex bits, 38-Piece https://www.amazon.com/dp/B000XW4C8Q/ref=cm_sw_r_cp_api_i_1KUIDbEY21808

Neiko 00244A Impact Socket Adapter & Magnetic Bit Holder, 4Piece Set | 1/4" Hex Shank with 1/4, 3/8, 1/2" Drive | CR-V https://www.amazon.com/dp/B07G1T6VBZ/ref=cm_sw_r_cp_api_i_rNUIDb8K71ZR9

Grey Pneumatic (103RA 3-Piece Drive Reducing Adapter Socket Set https://www.amazon.com/dp/B0021UGAL0/ref=cm_sw_r_cp_api_i_kSUIDbPCA0D1K

u/djkrugger · 2 pointsr/AskElectronics

The original black stick is pretty good but for bigger things like laptops and monitors you'll probably be better with something like this, some last longer than others but all are disposable, they are soft that's what are made for :)

u/Markbro89 · 2 pointsr/pcmods

frozencpu.com ships from Rochester, NY. They are great.

Lutro0-Customs.com is also in the states (apparently in a merger at the moment but a new store will be open tomorrow) I learned the most from there and purchased a good Pin removal tool from them and quality sleeving. frozencpu also carries most of Lutro's products.

Amazon.com also carries the tools.

I know your in Canada but I hope this may still help you.

u/Friendly_Psychopath · 2 pointsr/buildapcforme

The 4770k adds "hyperthreading" which will do almost nothing for gaming. Depending on the type of editing you do it may give you some benefit for that. I would recommend go over to /r/buildapc for some guidance on putting together your pc and they can look over my build to give you a second opinion (it is legit though). I have built two PCs for myself and all it takes is patience and little bit of attention to detail. About as hard as puting together some legos by following the directions.

Building Tips

  • Make sure you are "grounded" so static doesn't damage your components. You can get one of These

  • Make sure there are stand offs when you attach the mobo to the case.

  • It may be easier to put the cpu cooler on before you put the mobo in the case.

  • When adding the thermal paste to the cpu don't use too much there are plenty of videos you can find on adding thermal greese/attaching cpu cooler.

  • Make sure to be delicate with your cpu and that it is correctly lined up when you put it in the socket.


  • Don't turn on the computer without a cpu cooler attached or you will fry the cpu.

  • If it doesn't turn on first try or there is a problem it is probably something simple like a loose ram dimm so don't get too upset, the people over at /r/buildapc will help you trouble shoot if something goes wrong.
u/electricalfuckery · 2 pointsr/electricians

I bought this and it’s served me very well. All the tools priced out individually are a lot more than $88 bucks. I generally use these tools and an impact.

Tool Set with 3 Pliers, Wire Stripper and Cutter, 2 Screwdrivers 6 Piece Klein Tools 92906 https://www.amazon.com/dp/B004EKONLY/ref=cm_sw_r_cp_api_i_oruZCbZ15B962

u/Dubbys · 2 pointsr/electricians

Klein is the industry's choice but not the only choice. Milwaukee makes some great tools too. Their new channel locks are really cool for $20 ea.

This kit here

If you price it all out individually you save a few bucks I think. I dunno there's just so much. My first year I probably spent $750 and I still didn't have near enough tools

Bags, drills, extra batteries, boots... it all adds up so fast. All in due time.

u/V-chalk · 2 pointsr/Tools

I recommend these because they are reliable tools and aren't too expensive (subjective, of course). Nice tools will make you want to do more stuff yourself, I guarantee it! You probably can save some dough using Home Depot Husky / Lowes Kobalt/craftsman, or Harbor Freight. I have cheap tools too, but for the tools I use often, I invest a little more.

u/lelsunshine · 2 pointsr/electricians
u/Brandincooke · 2 pointsr/IBEW

Apprentice Tool Set for Trade Professionals, 6 Piece Klein Tools 92906 https://www.amazon.com/dp/B004EKONLY/ref=cm_sw_r_cp_apa_i_cX48Ab5YM6ZVZ

$72 is the one he is referencing I believe

u/arebe2 · 2 pointsr/Nexus5

I wrecked the headphone jack on my Nexus 5 and decided I would give DIY repair a try. It turns out that working on these phones is not terribly difficult.

Here's a $60-ish kit on Amazon with new screen and tools for the job: http://www.amazon.com/Display-Screen-Digitizer-Assembly-Google/dp/B00HPRZPHO/ref=sr_1_2?ie=UTF8&qid=1416507058&sr=8-2&keywords=nexus+5+screen

And a YT video on how to do it: https://www.youtube.com/watch?v=kbcPQ6JKoJA (the vid is 15 mins long, so worst case you might spend 30 minutes on a DIY).

If you're already considering a new phone but liked your 5 for one reason or another you might want to give this a shot first. I was surprised at how easy it was to work on. Worst case scenario you're out $60 and 30 minutes of your time, but best case you keep the phone you already paid for.

Quick Edit: Looking further at the link I placed to the Amazon kit the reviews are pretty bad. Do some research and consider buying the screen and tools separate. When I did my repair I bought this toolkit (http://www.amazon.com/gp/product/B008CLO7Q2/ref=oh_aui_detailpage_o04_s01?ie=UTF8&psc=1) and a $2 headphone jack replacement. Lots places refer to the Nexus 5 as the LG D820 as well, so you can search by that on AliBaba or eBay.

u/Gh0stP1rate · 2 pointsr/apple

No, the home button, and possibly camera and speaker, are different. They are mounted to the 5S digitizer and may not mount correctly to the iPhone 5 digitizer.

I smashed my iPhone 5s two days ago and fixed it myself.

I used these tools and this replacement screen, and followed the instructions in this video.

In addition to the tools, I used a piece of duct tape which was taped to my desk sticky-side up to hold all the screws in place after removing them, and used tweezers to pick them up and put them where they belong. I also needed a razor blade to open the case.

PM me if you have questions.

u/j-blizzle · 2 pointsr/E30

i like this one better, it cheaper and it looks like it has more wrenches and deeper sockets but I'm no expert on tool sets. Review looks better though.

https://www.amazon.com/Stanley-STMT71654-201-Piece-Mechanics-Tool/dp/B009EMKMCG/ref=sr_1_3?s=power-hand-tools&ie=UTF8&qid=1519083300&sr=1-3&keywords=mechanic+tool+set

u/bailsafe · 2 pointsr/motorizedbicycles

Here's what I used when I assembled mine:

  1. Socket set, metric, 8mm to 18mm with extension
  2. Phillips-head and flathead screwdrivers
  3. Drill with a 5mm or 1/4" drill bit
  4. Needlenose pliers (slip-joint could work too; I used both, they're cheap at Dollar General)
  5. Chain breaker for breaking the 415H chain (I used this one and needed a new master link too)
  6. Large cable ties
  7. Utility knife or snips

    If you need any recommendations for motorized bike accessories, let me know!

    EDIT: I just came back in from working on my bike, and I think something else you might find helpful is metric combination wrenches. I recommend this mechanic's tool kit, though I have some cheap Chinese TrueValue tools that work really well too.
u/Stopfortheelderly · 2 pointsr/Tools

My dad picked up a small toolbox from stanley when I was pretty young. 10 years later i'm still using the same 2 ratchets (I'm looking to upgrade soon though haha) i've been a diesel tech for almost a year now. About the same price range you'll still need to upgrade from that set, but it's pretty solid.

u/jtl216 · 2 pointsr/Fixxit

That's a tool kit that came on the bike stock. It's suppose to be held in by a strap under the seat but I take it most owners lost it.The tool kit was meant as more of an emergency kit to carry on the bike.

You're much better off buying your own sets of tools.

From all the recent maintenance I've done, you should be set with a set of metric sockets. Mainly 10, 12, 14mm sockets and allen keys up to 8mm. The spark plug is 18mm. You need a 19mm to turn the motor for the valve adjustment, and a 7mm for the small rightside cover. You should be able to get all that in a decent set.

And btw almost all the parts from 1989-2008 are interchangeable. The carbs in 2001+ bikes are a bit different, they're 3 circuit. The tank also changed, plus the fairings. Everything else though should be similar.

EDIT: This looks like a good tool kit, might be overkill though if you don't wrench that often or don't plan modifying more things once you're done.

u/kois1 · 2 pointsr/Tools

https://www.amazon.com/dp/B00F4AVRGW/ref=cm_sw_r_other_apa_i_blm8CbEMXQ9VF

I have the older iteration of this set in the trunk of my car. I've done most easy repairs and maintenance with it (tune-up, brakes and oil and transmission pan drop) it has a pretty thin profile and the case sucks but this one seems to be better from the reviews.

u/Derpandbackagain · 2 pointsr/Tools
u/1HONDAPRELUDE · 2 pointsr/Justrolledintotheshop

I got these for around $30 and absolutely love 'em. The magnetic and swivels are great.

u/kkemp13 · 2 pointsr/Justrolledintotheshop

Also found this on Amazon... GEARWRENCH 10 Pc. 1/4" & 3/8" Drive 6 Point 10mm Socket Set - 80319 https://www.amazon.com/dp/B00LH7DM14/ref=cm_sw_r_cp_apa_i_3SdXDbGN361DD

u/BabyWrinkles · 2 pointsr/CCW

I love my Tekton Everybit kit. Very compact, has every but I’ve ever needed.

TEKTON 28301 Everybit Tech Rescue (TM) Kit for Electronics, Phones and Precision Devices, 46-Piece https://www.amazon.com/dp/B00VJYWRKW/

u/Eckhart · 2 pointsr/Justrolledintotheshop

Totally man. I don't mind paying for good tools, but after a certain point you just get diminishing returns. The truck guys might make sense for someone who makes a living from their tools and, for some reason, can't drive to a store or wait 2 days for a replacement in the mail, but for anything else there's good tools to be found for reasonable cost.

For example, I love my Tekton 1/2" torque wrench. Thing is sturdy as hell, comes in a nice case, will do anything from 10ftlbs to 150ftlbs, and is only $40. It was the first tool I got from them, and I've been so impressed that nearly all of the hand tools I've purchased sense have been Tekton, if they make the tool in question.

I do occasionally end up at HF if I really need the thing same-day, or don't expect to use it more than a few times a year, but for the basics it's hard to beat Tekton in my experience. Hell, just the other day, I needed a T8 Securty Torx bit, so I ordered this thing and it's way better made than I expected it to be.

Reading back over this, I sound like a corporate shill, but I've found it hard to beat Tekton's intersection of price, quality, and Prime shipping.

u/BlackenedPies · 2 pointsr/24hoursupport

Ugh... Fix those links please:

https://www.amazon.com/dp/B01MRNIFR6/

https://www.amazon.com/dp/B01GF0KV6G/

Or use []() - [ name ] ( link )

u/StaircaseGenius · 2 pointsr/NintendoSwitch

I bought this set from Amazon and it did the job. I had a similar worry when I was replacing the backplate, but the SD card on its own little board and seemed to be pretty easy to remove. It really seems like they designed the switch with repairs in mind!

u/Jacob_9821 · 2 pointsr/Gameboy

It's reshelling a console with a single ribbon cable that connects the bottom and top parts. It's very easy.

Honestly, a 12 year old could probably do it. You won't break anything, I promise. I'd recommend buying the iFixit starter kit off Amazon for $20 and a shell for $10. The iFixit kit comes with tweezers, which you'll need to remove the rubber gromits on the top screen. That kit also comes with 16 screw bits for common jobs, a pick and a Jimmy. You won't need all of that for this swap, but it's a nice kit to have all and all.

Oh and by the way. You might want to go on eBay and find a seller who sells replacement shells with the hinges. The original hinges can be swapped out into the new shell, but it's a pain in the ass.

Links:

iFixit Essential Electronics Toolkit https://www.amazon.com/dp/B01MRNIFR6/ref=cm_sw_r_cp_apa_bW-OBbJNY69MQ

EXSEK Replacement Housing Shell Pack for Nintendo Gameboy Advance SP (Black) https://www.amazon.com/dp/B01H5TP9UY/ref=cm_sw_r_cp_apa_TW-OBbAQ3AEP4

u/MarkDubya · 2 pointsr/Nexus6P

I recently bought the iFixit Essential Electronics Toolkit from Amazon. It's got everything I need and more.

u/Rosati · 2 pointsr/Seaofthieves

Yeah no problem. I watched a tutorial video to make sure I knew what I was doing ahead of time but you'll need a set of T type drivers to be able to remove all the screws holding the controller together. A tutorial videos will explain everything but at a high level, you can pry off the back panel on the hand rests to reveal the back screws, removing those and the one behind the battery and you can get access to the board and buttons inside. After that, you'll want to carefully pull everything apart, keeping an eye on where everything came from. Then I did the same to a regular controller, I took the cosmetic parts and buttons from the SoT controller, and installed them over the hardware of the regular controller and screwed it all back together. When I was done it worked as well as the day I bought it.

u/hmspain · 1 pointr/3Dprinting

Excellent suggestion, thank you!

Just in case this posting sent you to Amazon wondering what a "swivel head deburring tool" was (like me)...

https://www.amazon.com/General-Tools-482-Swivel-Deburring/dp/B00004T828

u/multi_malt · 1 pointr/TheBrewery

Pro tip: use a deburring tool to cut the string. Much easier to get "into" the loop than with a knife.

Something like this: https://www.amazon.com/General-Tools-482-Swivel-Deburring/dp/B00004T828

u/cowanrg · 1 pointr/lasercutting

Interesting, I'll check out the thread. I have a lot of experience with ABS. It sure is stinky, but not toxic (unless you don't have any exhaust...). But I guess everything is toxic if there's enough of it ;-)

ABS can cut quite well, it does leave a tiny melted edge, but most of the time I just use a deburring tool to get rid of the edge.

u/insaneferret · 1 pointr/3Dprinting

a Deburring Tool is a tiny rotating drag knife that's perfect for cutting off brims

A solid pair of Flush Cutters is great for removing support and cutting filament blobs off before inserting into a hot end.

u/uomo_peloso · 1 pointr/crochet

I'd be worried about it catching on the edges of the hole. But I suppose if you used a deburr tool on it you could round off those edges.

u/philemon9130 · 1 pointr/guns

Edit: try a hand held hammer impact screw driver. http://www.amazon.com/Lisle-29200-Hand-Impact-Tool/dp/B0002NYDRG
Used them at a factory I was an engineer at to remove small loctite adhered screws.

u/pgkelly · 1 pointr/Fixxit

measure the screws and get replacements from a hardware store. If you don't have a thread gauge take a screw with you to the hardware store. (they are probably 6x1 or 5x.9)

next time get a hand impact: http://www.amazon.com/Lisle-29200-Hand-Impact-Tool/dp/B0002NYDRG/ref=sr_1_1?ie=UTF8&qid=1406914595&sr=8-1&keywords=hand+impact+driver

with a #2 Phillips or JIS bit.

u/boondoggie42 · 1 pointr/MechanicAdvice

Impact screwdriver. Suddenly those brake rotor retaining screws aren't so scary.

u/DatS30 · 1 pointr/Tools

Buy this for what you are doing. The rest of the tools you listed will strip the fastner.

Lisle 29200 3/8" Hand Impact Tool Set https://www.amazon.com/dp/B0002NYDRG/ref=cm_sw_r_cp_apa_4CBxzb6C1G17C

u/AllGloryToHypno-Toad · 1 pointr/fixit

WD-40 isn't super good for rusted bolts. Use either PB Blaster or there's a homemade mix that's supposed to be even better - I think it's ATF and acetone mixed 50/50.

Other than that, what /u/firematt422 recommended is dead on: grind a slot across the head and use a screwdriver or use vice grips.

If you try both of those and are still stuck, you'll want to pick up a handheld manual impact driver. (like this ; Craftsman sells one, too). With this, you'll twist while holding it from the side and wack it with a BFH. The internal gearing will force it to turn as it impacts.

u/nastynip · 1 pointr/HondaCB

I've def been there.

What you need is a rubber mallet, a regular hammer, and one of these suckers (you can probably find one at Ace hardware or O'reillys.)

Just use the impact driver on the screws, and once you get those out just hit the top of the cover with a mallet, and eventually it will come off.

u/Joker_Da_Man · 1 pointr/motorcycles

Ever heard of an impact screwdriver? I picked up this bad boy after drilling out a couple screws on my CB and I think something like this fellow could handle the screws in your pictures.

http://www.amazon.com/Lisle-29200-Hand-Impact-Tool/dp/B0002NYDRG/ref=sr_1_1?ie=UTF8&qid=1348868650&sr=8-1&keywords=impact+screwdriver

u/Ampliflier · 1 pointr/LifeProTips

Generally, the squeaking results from the treads (the part you step on) moving relative to the stringer or the nails in the stringers. If possible, fix the squeak using something like this: http://www.amazon.com/OBERRY-ENTERPRISES-3233-SQUEEEEEK-REPAIR/dp/B0006IK8YE

If you can't fix it (either because you don't own/live in the house, or you were unable to find a fix) then you're left with trying to walk up quietly. My experience is that stepping directly over the stringers reduces the noise. It minimizes the bending of the treads, and thereby minimizes the motion relative to the nails and stringers. So figure out where they stringers are, and set your feet on them as you walk up. Some stairs are always squeaky, so avoid them. If possible, lean forward a bit and put some of your weight on your hands.

Finally - practice. If you use this stairway regularly, you can probably learn to walk up it silently.

u/totorozawa · 1 pointr/NewParents

I just moved and had new carpets installed and completely missed this step during our renovation. Can anyone vouch for this solution? https://www.amazon.com/OBERRY-ENTERPRISES-3233-SQUEEEEEK-REPAIR/dp/B0006IK8YE/

u/Kumquatelvis · 1 pointr/Vive

You might look into Squeeeek No More.

u/jsonoson · 1 pointr/HomeImprovement

Something like this on Amazon is what I was thinking, there are many diff brands I believe:

O'BERRY ENTERPRISES 3233 "SQUEEEEEK NO MORE" FLOOR REPAIR KIT
https://www.amazon.com/OBERRY-ENTERPRISES-3233-SQUEEEEEK-REPAIR/dp/B0006IK8YE

u/knetzere11 · 1 pointr/DIY

These screws sink threw your carpet and then you snap off the heads. Never used it but saw it on ask this old house

O'BERRY ENTERPRISES 3233 "SQUEEEEEK NO MORE" FLOOR REPAIR KIT https://www.amazon.com/dp/B0006IK8YE/ref=cm_sw_r_cp_api_4tMYAbJ1SC011

u/itsthedaubs · 1 pointr/DIY

O'BERRY ENTERPRISES 3233 "SQUEEEEEK NO MORE" FLOOR REPAIR KIT https://www.amazon.com/dp/B0006IK8YE/ref=cm_sw_r_cp_apa_BvMYAbP4ECXK4

u/Rage321 · 1 pointr/DIY

I swear by THIS.

u/jackalooz · 1 pointr/InteriorDesign

Have you tried the squeak no more kits? Can’t vouch for them personally, but some people here have had luck. I would very rarely want to replace hardwood with engineered wood. And my bet would be that you go to all the trouble, and they still squeak.

u/Infinity_fan · 1 pointr/DIY
u/masturbathon · 1 pointr/Tools

I can't comment on those, but I have some very similar Irwin pliers that only cost a few dollars more and they are excellent!

http://www.amazon.com/Tools-VISE-GRIP-GrooveLock-2-Piece-2078709/dp/B000FK1R0W

u/Xb3am · 1 pointr/homeowners

For the tool kit you want to start with something like this. A kit with just the basics. You will probably also want to get a drill. After that you should to buy your tools based on the project you are working on. You will eventually buy a better hammer and screwdrivers and every thing else in your starter kit, but as a new homeowner this should be enough to get you by until the bigger projects come along.

As for Home Depot and Lowes, they are generally about the same. As /u/twynkletoes said, go for the deals.

u/NoNameForSteve · 1 pointr/AskMen

I would even go one further, and it's something that's without fail for me - A small set of tools. You can buy an "OK" set of tools, in a box set (screwdrivers, ratchet sets, wrenches, etc) for cheap. You don't need to spend $1000 on something, just a basic cheap set. I have one sitting in my car for emergencies, and it's come in handy many times in a pinch! Just found one on amazon for about $35. Super cheap, super handy.

Just stash that kit in a closet or something. Better to always be prepared than to not be!

u/SierraHotel058 · 1 pointr/DIY

There is something oddly satisfying about owning tools, and acquiring them. A lot of people that already possess a large set of tools would actually enjoy being in your position: starting all over again!

I do think that many people start out a little too strong, trying to anticipate all their needs and buying tools on those perceptions. Often the result are many unused/under utilized tools...when the money could have been spent better elsewhere. The best way IMHO is to acquire a basic starter set...and then acquire tools one or two at a time as the needs arise.

I would also resist the temptation to buy top quality tools (some will take exception to this) at the accompanying high prices. The truth is that most homeowners/DIY people are really not that hard on tools. Moderate quality tools will often last a lifetime. I still own and use a low end socket set I bought 45 years ago. A homeowner has no need to drop a bundle on a SnapOn socket set or high end Bosch power tools.

Good Luck, and have fun!

u/-filly- · 1 pointr/Random_Acts_Of_Amazon

Well, I have had the good fortune of never needing to really fix anything or make anything, so I am a man that has no tools. This home repair kit would be a nice start :) I hope your journey went well (since it's already the first week of August, and this is a month old)

u/Seitanist666 · 1 pointr/Tools

Harbor freight has a master set that has all the specialty bits. 1/4 bits are universal, there's a larger size used for impact drivers but they aren't common. My problem with the harbor freight torx is the metal used is very soft and they bend with very little effort. I highly recommend this set https://www.amazon.com/Sunex-9726-Mini-Ratchet-38-Piece/dp/B000XW4C8Q#immersive-view_1466790828525

I have the same set rebranded as Cornwell that I use daily and have never broken a bit. Matco also rebrands this set.

u/FrankyFe · 1 pointr/Tools

Yeah, 1/4" bit ratchets work great for tight access and are popular. Among several, I have the wiha one mentioned by others and I used it last on my car for a rocker panel fix without removing the tire.

And ya, I've looked around a lot for myself but I haven't seen a 4mm drive ratchet and an adapter would cut into your clearance. So I suggest a 1/4" bit ratchet + 1/4" bits as they are not expensive. I'm thinking of getting a few more to scatter about, and here's one I'm looking at now: https://www.amazon.com/Sunex-9726-Mini-Ratchet-8-Inch/dp/B000XW4C8Q

u/DeeJayDubbs · 1 pointr/Tools

This is the one I have.
TEKTON 28301 Everybit Tech Rescue (TM) Kit for Electronics, Phones and Precision Devices, 46-Piece https://www.amazon.com/dp/B00VJYWRKW/ref=cm_sw_r_cp_api_i_qOS3CbA3BH6C1

It doesn't have a ratchet though. If I need one, I use the one from this standard bit set.
Sunex 9726 Mini Ratchet and Bit Set, 1/8-Inch - 1/4-Inch S2 Bits, 5/64-Inch - 1/4-Inch hex bits, 38-Piece https://www.amazon.com/dp/B000XW4C8Q/ref=cm_sw_r_cp_api_i_hQS3CbW3TQA1A

u/millerhkl · 1 pointr/Gunpla

Adding on to what everyone else has said, /u/goodguydan introduced me to the spudger on his beginner's guide. Didn't know these things existed and some of the reviews are hilarious.

You don't have to shell out money for a piece of plastic, but I would recommend using something other than a metal blade to reduce the chance of scratching or otherwise damaging parts when disassembling. I've grown used to the nylon spudger, but I imagine you can fasten something similar out of a piece of "softer" plastic.

u/DaveIsLame2 · 1 pointr/sysadmin

With those mechanix, it generally isn't a problem. For the stubborn/inset rj45's I keep a plastic spudger handy. (surprisingly usefule for lots of tasks.) http://smile.amazon.com/3M-SP3010-Nylon-Spudger-Tool/dp/B001DD1UJS

But i dont usually have my gloves on when doing patching; just for racking and opening cases.

The only thing I don't like doing with gloves is screws.

u/steak_master · 1 pointr/Gunpla

I just built the MG Epyon EW a few months ago and it definitely didn't come with water slides. It came with a dry decal sheet, a small sticker sheet for eyes, sensors, and orbs, and a sheet of sticker decals. Did you get them extra with the kit? Also I found the best way to do dry rub decals is to cut out around it, then tape it to the kit and rub it on. I use a Nylon Spudger. /u/goodguydan recommended it, and I think it's a great tool with a lot of uses.

u/SATANS_SPIKEY_DICK · 1 pointr/buildapc

Well, I don't think there are really that many specialized tools the average user would need. I guess if you want to do some minor modifications or sleeve your psu, you would really benefit from some specialty tools. Generally speaking, I think nearly everyone would benefit from:

u/Skidkidd · 1 pointr/CableManagement

Actually I didnt really buy any kind of kit, just found some paracord I liked and bought it. also I purchase this mod kit being that I could not find a place that sells the tool individually and because Im a amazon prime member =D But the included pin removal tool was worth the price. Made my life a hell of a lot easier. Thanks for the tips though

u/sirdroftardis · 1 pointr/buildapc

You did a great job and I hope you have fun building your first computer. Three things I would do/get though, otherwise you have everything.

  1. get this, the links below will explain why. http://www.amazon.com/KingWin-Anti-Static-Wrist-Strap-ATS-W24/dp/B0042TLA90/ref=sr_1_5?ie=UTF8&qid=1404951432&sr=8-5&keywords=anti+static+wrist+strap

  2. watch this, it shows you how to build carefully and correctly. https://www.youtube.com/watch?v=d_56kyib-Ls

  3. Watch this( the 3rd video).

    The first video in the series ink the links is about choosing parts which you already did. https://www.youtube.com/watch?v=RxaVBsXEiok
u/Klathmon · 1 pointr/buildapc

Get this as part of your build.

I used my old one so much that I actually bought a full $50 mat and grounding system for my most recent build.

u/knight_47 · 1 pointr/buildapc

Out of budget? They're literally a couple of bucks at my local Fry's Electronics, or $3 on amazon

u/angrypenguin54 · 1 pointr/buildapc

Hey dude... this video is a much better tutorial.

http://www.youtube.com/watch?v=d_56kyib-Ls

The way that the anti-static bag is it actually collects all the ESD damage on the outside of the bag, rendering the inside safe. A couple things you can do is actually just put it on the outside of the motherboard box, which is cardboard and non-conductive, wear rubber soled shoes and pick one of these up for 4 bucks.

http://www.amazon.com/KingWin-Anti-Static-Wrist-Strap-ATS-W24/dp/B0042TLA90/ref=sr_1_2?ie=UTF8&qid=1341874779&sr=8-2&keywords=esd+wrist+strap

You attach that to your wrist and a piece of metal (A part inside the case and this will keep you grounded)

Let me know if you have any other questions.



u/TylerJaden24 · 1 pointr/pcmasterrace

Thanks dude, very helpful.

Edit: Well he's talking about how cordless is garbage, which makes sense. I bought this strap will it work well for me? It's not like the one he's using where he plugs it into something. If I connect it to my case will it count as being grounded?

u/TitanSmoke · 1 pointr/electricians

Tool Set with 3 Pliers, Wire Stripper and Cutter, 2 Screwdrivers 6 Piece Klein Tools 92906 https://www.amazon.com/dp/B004EKONLY/ref=cm_sw_r_cp_api_i_9KPRCb0BHWQMZ

u/vtfulton · 1 pointr/electricians

http://www.amazon.com/Klein-Tools-92906-ProPack6-Apprentice/dp/B004EKONLY

I recommend this set of hand tools and Milwaukee Fuel for your drills.

u/promonk · 1 pointr/mildlyinteresting

Dunno if this will help or not: https://www.amazon.com/Newer-Tech-TOOLISESAMO-iSesamo-Electronic/dp/B00792JJK4

I love this thing. I use it all the time while doing small device repairs.

u/epicflyman · 1 pointr/Random_Acts_Of_Amazon

A new quiver would not go amiss as my DIY one tends to collapse. Otherwise, I'm always running out of loc-tight and I go through pry-tools like nobody's business.

u/cutol · 1 pointr/thinkpad

I used one like this to crack open my t560. The part that was tough was the part near the battery where you need a screwdriver to jab up that last bit.

The 2nd time through its much easier, only a thin metal spudger required.

u/Exfiltrate · 1 pointr/EDC

You NEED to get one of these if you don't have one already. The single best metal pry tool I've ever used and I use it for every phone/laptop repair

http://www.amazon.com/gp/aw/d/B00792JJK4/ref=mp_s_a_1_1?qid=1450883592&sr=8-1&pi=SX200_QL40&keywords=cell+phone+pry+tool+metal

u/embrow · 1 pointr/Entrepreneur

Buy a toolkit and a screen or two and set up a simple wordpress website offering phone repair in your town. Start a facebook page and find friends with broken phones and spread the word. Charge $100 per fix, takes 10 minutes and you'll be doing great for a 16 year old.

u/video_descriptionbot · 1 pointr/LineageOS

SECTION | CONTENT
:--|:--
Title | Samsung Galaxy S4 Proximity Sensor Fix - How-to
Description | The proximity sensor on my Galaxy S4 stopped working, whenever I took a call the screen would shut down and won't come back on again, I discovered it had a lot of lint and dirt blocking it, I hope this video helps people with similar problems. UPDATE: Here is the link to Amazon for the toolset I use in this video: http://www.amazon.com/Olympia-Tools-88-670-15-Piece-Repair/dp/B008CLO7Q2/ref=sr_1_3?ie=UTF8&qid=1422889599&sr=8-3&keywords=iphone+tools&pebp=1422889603890&peasin=B008CLO7Q2
Length | 0:10:42






****

^(I am a bot, this is an auto-generated reply | )^Info ^| ^Feedback ^| ^(Reply STOP to opt out permanently)

u/good_guy_submitter · 1 pointr/buildapcsales

Also a computer repair technician here. I have both the harbor freight set and this iFixit set and the iWork set..

When comparing them, the only difference between the harbor freight set and the Ifixit is it that the 52-bit iFixit kit is the only one that comes with Apple pentalobe drivers, which is kind of a big deal. Quality wise however, the Ifixit set feels pretty crappy and isn't any better than the harbor freight set. On the other hand the iWork set is amazing in quality and craftsmanship and has elongated drivers to reach deep socket screws, I love my iWork set and will use it before anything else unless I need an Apple bit which only the iFixit has.

u/plankingdom · 1 pointr/Tools

I didn't think about Stanley tool sets at all, was this the set you got? I might get that set along with a few other necessities.

u/lushkiller · 1 pointr/buildapcsales

Well if you're just looking for something with a lifetime warranty, I should also mention Stanley tools. I bought my dad this set on sale for like $50 or so a few months ago because all of his tools are at my house because we are renovating. Stanley is a respected brand (owned by black and decker) and the tools seemed to be good quality and have a limited lifetime warranty. Their smaller sets are also probably worth looking at. Also, just check the shelves at your local Lowes or Home Depot because I was able to get my Kobalt set for $100 after it had been clearanced from $240.

u/OThatSean · 1 pointr/subaru

My tool buying philosophy, that I learned from a man much wiser than my self, has been "buy the cheapest version of a tool, if you break it than it is worth it to buy an expensive version. If it can't do the job at all return it." So I always buy the harbor freight tools first. So far I have only had 1 thing break and that was the cheap ratchet that came with my socket set from Stanley. I bought a fancier one Harbor freight sells for about 15 bucks and it is a champ so far, but if I break it I'm ordering a snap on.
The Stanley set I bought(and kinda regret): https://www.amazon.com/gp/aw/d/B009EMKMCG/ref=mp_s_a_1_4?ie=UTF8&qid=1474051431&sr=8-4&pi=AC_SX236_SY340_QL65&keywords=stanley+tool+set&dpPl=1&dpID=4135F1HHjPL&ref=plSrch
The Harbor Freight ratchet I thus far love: http://m.harborfreight.com/38-in-drive-professional-flex-head-ratchet-62321.html
The Snap on I will buy if need be: https://store.snapon.com/Dual-80-174-Technology-Compact-Head-3-8-quot--3-8-Drive-72-Tooth-Compact-Flex-Head-Ratchet-P648783.aspx

u/jgur88 · 1 pointr/HondaCB

TL;DR: If you have the $400, buy the bike. Get some good, basic tools. Read the service manual/watch YouTube carefully! Make sure you have basic bike things (lube, pump, etc)

Ok, so if $400 is an amount that doesn't seem like much to you, buy it. If $400 makes your finances tight or you feel $400 is a lot of cash, I would think twice. Below, I am going to suggest some basic, quality tools to have you maintain the basics of the bike which will add up to more than one normally anticipates. Also keep in mind title transfer fees and sales tax depending on your state. I got my bike for $400 but paid $180 more to transfer it.

I know tools are expensive because I started out with none a few years ago. I was always getting by with just a cheap set of screwdrivers and vice grips which was marring surfaces and stripping screws/bolts. At the minimum, I would have a nice set of sockets, screwdriver (with various bits), basic wrenches, allen key set, and vice grips. I use these five things on both my bikes, on my cars, and around the house almost daily. I bought [this tool set] over the winter and am so glad I did. For this bike, it is going to have almost all of what you need. It won't have a socket big enough for your axles and maybe some other stuff, but the vice grips will work well. Around 75% of the small nuts/bolts on a CB bike will need a 10mm wrench so you can never have too many of those. Almost all of the small nuts/bolts after that will take 8 or 12mm so those three are pretty key. The tool set I suggested has all of those and much more. On old bikes, you will run into nuts/bolts that aren't original and may not be metric, so the tool set I showed will cover that too. The allen keys in the set are pretty basic but are also needed. You don't need a torque wrench, caliper, or multimeter, but they are nice to have and over time you may want to pick them up when you have extra cash. Knowing the difference between hand-tight, snug, and tight will go a very long way. Lastly, I keep a coffee can full of screws, nuts, washers, or anything I find during the day. Everytime I see a little bolt or washer in the house or on the street, I pick it up and toss it in. The can is now full of little things I use to replace missing stuff all the time. It saves me the time of going to the hardware store and finding a replacement let alone the money.

Make sure you have basic bike things like lube, degreaser, grunge brush, etc. For lube and degreaser, make sure it is compatible with your chain type (like o-ring specific). A bicycle pump with a PSI gauge will keep your tires inflated fine ($20 to $40 pump, I prefer Park Tool brand or Topeak). A bit of tin foil and water gets rust out of chrome easily (YouTube it). Simple Green is a good cleaning fluid also for vehicles/everything and PB Blaster will loosen stuck/rusted stuff instead of breaking off the head trying to force it off. WD-40 is a must as well. As you want to do more on your bike like change tires, valves, or whatever, you may want to buy stuff like tire irons or feeler gauges if you can't borrow them off a friend. The specialty tools will add up fast so I prefer to borrow them as you may only use them once a year.

Before I do anything on any vehicle I buy, I make sure I have the service manual. I have a tendency to mess a lot of stuff up if I'm not looking at directions carefully. Most Honda service manuals are free online, so search on this sub or do some googling for a PDF. YouTube has recently become a great resource for DIY mechanics. For some reason, people have been stripping their bikes down and videotaping a lot of it. For my bike, there is a 23-video series from some redneck on taking the carbs apart. I watched him adjust the valves for two hours before I went ahead and did them myself in 30 mins. The manual combined with some YouTube will help you about 90% of the time. The last 10% will be trial and error and your experience with the bike over time.

u/Wall_Investigator · 1 pointr/MGTOW

Here it is

Crescent used to be a decent brand, but a lot of it is cheapo Chinese quality now. They're made of inferior metals and rust easily.

Of course, quality tools are expensive. So, a general piece of advice is to first buy a cheapo version. If you use it enough that it breaks, then you may consider upgrading to a nicer brand of tool (Klein, Channellock, Snap-On, Armstrong, etc.).

That's a good field to get into. You'll be making enough $$$ to buy great tools & other nice toys. Just watch out for thots that will try to take it.

u/steinmb · 1 pointr/HomeImprovement

I've had a similar set to this for well over a decade. It fits nicely in my vehicle and is still my go to from oil changes to timing belt swap.

u/dan_blather · 1 pointr/Tools

My girlfriend won me this Crescent set at a silent auction a while back. It's only $50 more on Amazon, has good reviews, and the quality of most of the pieces is surprisingly good - solid, high polish, mostly Taiwan. I use it whenever I have to carry tools somewhere, and I'm too lazy to pick and choose out of the roll cab.

u/The_fuck_up_fairy · 1 pointr/Tools

Also, I bought this set for my truck. I put the entire thing into a tool bag and it fits under my drivers seat.


https://www.amazon.com/Crescent-CTK170CMP2-Mechanics-Tool-170-Piece/dp/B00F4AVRGW

u/PissOnUserNames · 1 pointr/motorcycles

https://www.amazon.com/Crescent-CTK170CMP2-Mechanics-Tool-170-Piece/dp/B00F4AVRGW/ref=mp_s_a_1_5?keywords=tool+set&qid=1572272720&sr=8-5

Something like this will get you well on the way you might need a few other tools to accompany. Buy those as needed I wouldn't expect the pliers to be very good do not except them to not hold up. I once heard buy cheap tools to get you started and as they break replace them with more expensive ones because that's what you use the most.

u/smedema · 1 pointr/mechanics

The oil filter cup won't and maybe not the t25 but the 19mm should. Those specifically are the tools you will use though. Edit: the second set looks like it might have a t25 in it. If you can swing it I would get something like this. It will be more useful and will allow you to do more if you choose to. But as for your other question. I was thinking of the 2.5 for the oil filter cup but the 2.0 is a 32mm socket. It's been a while since I've seen a 2.0 lol. Used to be a VW tech now am an Audi tech. But ya the drain plug will be a 19mm and you should replace it everytime you do an oil change (about 3 USD for a new one). Most VW/Audi filters will be that cup, a 32mm or a 36mm. You have a 32mm filter housing which will not be in the kits.

u/Thighbone · 1 pointr/EscapefromTarkov

I'd be wet if I hadn't seen this while searching for the above:

https://www.amazon.com/Gerber-Ding-Dong-Breaching-Tool-30-000790/dp/B00KYO6BXM/ref=pd_day

u/Ctrl_Alt_Del_Esc · 1 pointr/Rainbow6

Gerber Ding-Dong Breaching Tool


The irl version if anybody wants to become Sledge irl

u/Its_bigC · 1 pointr/askcarguys

KD Tools 80319 Master Socket Set https://www.amazon.com/dp/B00LH7DM14/

u/69_DirtyMoney_69 · 1 pointr/Tools

Amazon sells a nice set too. I've had it for like 2 years now. I painted them all bright red the first day.

https://www.amazon.com/dp/B00LH7DM14/ref=cm_sw_r_sms_apa_i_ZCWZDb25J1TXG

u/ehdrian · 1 pointr/Edmonton

I've personally used the following kits:

Kit Option 1

Kit Option 2

Both are great. The second kit adds a few tools for mobile device repair/fat finger support.

u/Paul_Swanson · 1 pointr/computertechs

I have this: https://www.amazon.ca/TEKTON-2830-Everybit-Precision-Electronic/dp/B009MKGRQA and like it a lot. They also have larger kits - https://www.amazon.ca/TEKTON-28301-Everybit-Electronics-Precision/dp/B00VJYWRKW looks promising. I use this https://www.amazon.ca/Titan-11009-Fits-All-Phillips-Screwdriver/dp/B000PJHO14 for desktop computers (though I paid a fraction of that at Fred Meyer's).

I've never been a fan of prebuilt tool kits.

u/HoeYouknowme · 1 pointr/IndianGaming

https://www.amazon.in/dp/B00VJYWRKW/

I was eyeing this one but price went from 2k to 4.7 and that seller vanished

u/eddiegrey · 1 pointr/rccars

Found a nice set of tools on Amazon for $20
Kinexsis Ultimate Air/Surface Startup Tool Set https://www.amazon.com/dp/B017CIT05I/ref=cm_sw_r_cp_apa_XRasybWWE16QG

Does that kit look to have the correct sizes???

u/firmware-god · 1 pointr/macbookpro

You can buy one of the following toolkits. They are amazing for its price and you may reuse them at some point. I use them all the time. Don’t ware money on cheap shit. You will damage your expensive peace of tech.


iFixit Essential Electronics Toolkit DIY Werkzeugset bit set für iPhone Elekronik PC laptop Reparatur https://www.amazon.de/dp/B01MRNIFR6/ref=cm_sw_r_cp_api_i_zddjDb18ZHN7T


iFixit 64 Bit Driver Kit Set mit 64 lange bits aluminium bithalter präzisionswerkzeug steckschlüssel schraubendreher torx security imbus kreuz schlitz diy präzisionswerkzeug https://www.amazon.de/dp/B0189YWOIO/ref=cm_sw_r_cp_api_i_MedjDbAG0BBPX


iFixit Pro Tech Toolkit inklusive 64 Bit Driver Kit DIY werkzeug set zum reparieren reparatur reinigung schrauben öffnen von handy reparatur smartphones laptops und elektronik https://www.amazon.de/dp/B01GF0KV6G/ref=cm_sw_r_cp_api_i_afdjDbNPDVSWX

These are German links. But google the toolkit name that you want and buy on your amazon page. Every of these three kits contains the screwdrivers that you need. I recommend you go for the last one since it includes good extra tools you may need.

u/PvM_Virus · 1 pointr/askTO

Hey, the iFixit kits should be available on their site (?) but if not then I bought a set off of amazon for the same price so you can check there. But otherwise, a lot of hardware store do have Phillips 00 screw drivers, they’re usually bundled into sets

Edit: This is what i have, and is more than enough to work on your laptop

u/a_lumberjack · 1 pointr/bicycling

Soft nylon guitar pick?

Cell phone repair kits are handy to have around for this sort of thing. Good ones will come with a variety of pry tools, and a selection of tiny screwdrivers (Torx, Pentaglobular, Phillips) for electronics.

iFixit Essential Electronics Toolkit is an example https://www.amazon.ca/dp/B01MRNIFR6/ref=cm_sw_r_cp_apa_i_.iV0CbWEGRNM1

u/twistedhypnosisvic · 1 pointr/laptops

You need to check for compatibility between models (RAM and laptop)

A new ssd or hdd. what ever u prefer. hdd is cheaper and a lot more memory but a lot slower. it should have extra slot for a 2.5 inch hdd/ssd so u could add a hdd and upgrade the included ssd(but that one has windows on it)

It is not very hard. just open it using iFixit and u r good to go. just dont touch anything inside you dont need to. there is also a lot of content online about this. (YouTube)

​

as far as adding a new hdd. it is pretty simple. u install it inside and check to see if Device Manager recognizes it and then look up how to set up the partition for it. (super easy just google it and it takes like 2 minutes)

u/KDLGates · 1 pointr/Vive

Yup, product description says (among others) Phillips 0, 00 and 000.

So you'll have one correct tiny one and two more even tinier ones.

If you are somehow looking to spend $20 instead of $10, I personally have my eye on the iFixit Essentials Kit.

u/mezekaldon · 0 pointsr/Plumbing

A 2' Rigid aluminum pipe wrench should do the trick. I've never seen mine lose a fight against 1/2" brass.

You could probably get away with a 10" or something, but that doesn't sound like nearly as much fun. Or the cheaper version of knipex

Also, counterclockwise to loosen. And hitting the threads with some wd-40 cant hurt.

u/xcheck76 · 0 pointsr/GeekSquad

Get one of these tools for your precinct, and remove the grip pads from the sides.

u/jcpb · 0 pointsr/Android

> Pentalobe screws introduce a lot of friction.

Laziness is not an excuse when you're repairing devices.

u/DrDrater · 0 pointsr/IWantToLearn

this is the set I use: https://www.amazon.com/TEKTON-28301-Everybit-Electronics-Precision/dp/B00VJYWRKW/ref=sr_1_45?s=hi&ie=UTF8&qid=1525562304&sr=1-45&keywords=precision+screwdriver+set

Gotten me through literally hundreds of repair jobs. Has a nicer screwdriver than most sets that I have seen, and I like that it is a soft clamshell so you don't have to worry about it shattering if you throw it in your backpack.

u/StarManta · -1 pointsr/HomeImprovement

"Questions like this" is not "this question". In particular, I asked for something that fits together well. A box full of a dozen different things I bought independently will never fit together like, for example, this kit does, and it will never be as easy to use. Bits and pieces will get scattered and strewn around the box and I'll never know if I've misplaced a particular piece unless I go to use it. That link may be a useful checklist for things to make sure the kit includes, but TBH it is exactly what I'm trying to avoid by seeking one that is designed to go together from the get go.