Best power impact drivers according to redditors

We found 109 Reddit comments discussing the best power impact drivers. We ranked the 53 resulting products by number of redditors who mentioned them. Here are the top 20.

Next page

Top Reddit comments about Power Impact Drivers:

u/i_eight · 25 pointsr/delusionalcraigslist

Just as an aside, get the one with the 1/4" chuck, then buy the 1/4" to 1/4", 3/8" and 1/2" adapters. The 1/4" chuck is way better than would seem, and the boss ring on the 3/8" falls out pretty much instantly, meaning it won't hold sockets. Trust me, I've used all the DeWalt cordless impacts, the 1/4" punches way above it's weight.

u/No-Coast-Punk · 15 pointsr/Justrolledintotheshop

This is the correct answer.

Get the high-end version of this and never sweat those stupid things again.

The impact helps to shake any rust loose behind the fastener. The impact also forces the tool to engage the Fastener walls better so it doesn't slip.

It was maybe once a year that a hand impact would fail to get these out first shot.

https://www.amazon.com/gp/aw/d/B01F5XOFFM/

u/iron_naden · 15 pointsr/homeowners

I agree with anyone else who's saying to just buy stuff as you need it rather than pre-buying stuff you may never need. When you do buy things, absolutely buy quality. There are some worthless brands that you'll usually regret owning, like Ryobi; there are brands that you will never regret owning (although you might regret overspending based on your usage) such as Milwaukee; and there are brands in the middle, such as Hitachi & Bosch.

The trick is that some tools are more important to buy quality than others. Most hand tools like hammers & screwdrivers are universally simple and it doesn't matter what brand they are. This is also true of select power tools, including angle grinders and bench grinders--go ahead an buy the cheapest option on those because I've never seen one fail. Other tools are literally garbage if you cheap out, such as cordless drills.

Apart from basic hand tools like hammer, tape measure, screwdrivers, etc, the only tool I'd consider indispensable is the cordless impact/drill driver. It's the most used tool in my house by far. I personally own this Hitachi model and it's bulletproof. Get a bit set to go with it.

Some other wisdom:

  • Don't waste money on bleach-based cleaners. Buy bleach and mix with water in a spray bottle at 1:4-1:9, depending on how brutally you want to clean your shower/mold accumulator. (LPT: clean you showers & toilets every couple weeks before they start growing visible mold)
  • Vinegar is also a cheap cleaner and substitutes for CLR in many cases, such as cleaning scale deposits on glassware & shower doors.
  • Use white rags to clean surfaces instead of paper towels. Cheaper/less wasteful. Then use bleach when you wash a load of rags.
  • Watering your lawn is a massive waste of resources. Don't get sucked into the perfect lawn contest that many neighbors seem to play. When I see a lush, green lawn during the dry heat of summer when sensible grass has gone dormant I mentally flag that person as an insecure douche who's a big contributor to the tragedy of the commons that is our water consumption and general treatment of natural resources.
  • Fertilizing your lawn is even crazier to me. I see neighbors with fertilized lawns, with their "keep pets, children, & pregnant women away" signs, and I think of the excess nutrients running off into the storm water and polluting rivers and lakes. And for what, grass on steroids that you have to mow more often? If you're looking to waste more of your time on lawn care then I have a lawn you can come mow. Basically this is just another plea for you to not try to "keep up with the Joneses."
  • Label your breakers, or double-check them if they're already labeled.
  • Whenever you have something go wrong, search youtube for the problem first. You can save a boatload of money by DIY. Example: My clothes dryer stopped heating. Instead of a service call, I spent 10 minutes on youtube watching someone else fix my exact problem, then bought a $5 part on amazon, and spent another 30 minutes fixing the issue myself.
  • Buy a clothes drying rack or hang up a clothes line in your laundry room. You can save a ton if you're not using the dryer all the time.
  • If you're going to stay in your house long-term then go buy LED bulbs to replace any incandescents. Replace CFLs as they burn out. If you're not going to be there forever, just buy CFLs if you want to save a little money. The energy savings from incandescent (~60w) to CFL (~13w) often makes more sense than spending extra to get LED (~9w). However, do buy LED for all of your most-used fixtures, or if you have kids that always leave lights on. That extra efficiency pays off when you're talking about the kitchen or living room where a light is on much more than the guest bedroom, for example. Don't overlook outdoor fixtures, especially for things like motion-sensing lights, where an LED flood light can save a bunch over halogen.
  • Make sure to clean things that circulate air, as clogged radiators reduce efficiency and increase wear/tear. Key places to keep clean include your furnace filter, central AC condenser (these collect a LOT of dust/debris), clothes dryer vent (and lint trap), and refrigerator.
  • Use an app like Google Keep to keep a list of housework to-do. You can add to the list anytime you think of stuff so you don't forget what needs to be done around the house as you have time.
  • Try to do one small project every night, or whatever schedule makes sense to stay ahead of the never-ending list. Don't let your to-do list build up. If you get behind on it, just pick something and get it done rather than stressing about how much housework you have to do.
  • Don't put any food waste down your sink/toilet/drains. Don't use your garbage disposal to dispose of garbage (I know, such a misnomer). Especially anything containing fat because it congeals in your sewer line & causes problems. If you have food waste, put it in the trash (or compost). Better to take out the trash more often than to pay a plumber hundreds to unclog your sewer.
  • Don't overload your washing machine. Also, wear clothes several times before washing if possible, especially jeans. You don't necessarily have to wear the same thing day after day, but most clothes don't get dirty enough to warrant washing after a regular day for many people. Obviously if they stink then wash them, but for example I rotate two pairs of jeans every other day for two weeks and then wash them. This saves you time & money.
  • Key all your locks the same.
  • Don't get too obsessed with DIY-ing everything that your quality of life suffers. Sometimes it's totally justifiable to pay a professional to do work so you can enjoy life or do other things.

    Edit: Formatting help lied about how to format a bullet list.
u/dxrey65 · 12 pointsr/MechanicAdvice

Manual impact driver. Pretty much an essential tool, and it's the only thing that works reliably well on those.

u/kr0ntabul0us · 11 pointsr/MechanicAdvice

This. Definitely a hammer-style impact driver. Something similar to this 648002 1/2" Dr. Impact Driver Kit https://www.amazon.com/dp/B004QO9FK2/ref=cm_sw_r_cp_apa_i_V1y6CbDD8GZR3

u/awkwadman · 4 pointsr/MechanicAdvice

If you get an impact screwdriver those things wont strip and come right out. Can't say the same for the rotor, but the screws will be easy.

I cant speak for this product, but this is the same type I use.

u/ickybus · 4 pointsr/Skookum

Cool, you saved $0.00...

I bought a couple of these last black friday for $99 and then sold them on Craigslist for $120. Good driver, but my personal one is the new brushless one.

u/Necoras · 3 pointsr/DIY

A lot of people are saying leverage, which will work. Alternatively, go with a power tool! Find the right sized bit (no idea if any of that set matches) and an impact driver and you should be able to unscrew it without much difficulty (after much soaking in penetrating oil).

u/kowalski71 · 3 pointsr/cars

I know tools so here we go. Focusing on the extras, luxuries, and conveniences. If I don't specifically note a manufacturer/model I probably just grabbed the first Amazon link to make it clear what I'm talking about.

  • 12v impact gun/electric ratchet. These are an awesome luxury for working on cars, much time spent turning ratchets will be saved. Also useful around the house for driving sheetrock screws. I like the Bosch PS41 for bang for the buck and Milwaukee M12 for the full 12v set (they have a ratchet, Bosch doesn't).
  • Fucking magnet trays, how do they work?!
  • Amazeballs stocking stuffers: finger bit adapters.
  • Timing light
  • Torque wrench
  • Dremel. I have the cordless one because every Dremel I've ever broke has failed at the brushes and it has a BLDC but that's actually been a really useful feature for working on cars. Grab and go.
  • 4.5" grinder. Pick your favorite color but you usually can't go wrong with yellow or red.
  • Wobble extensions
  • Hex and/or Torx bit set
  • TS8000 MAP gas torch and bottle. I should've put this higher cause this is crazy useful and everyone needs one.
  • Decent wire strippers
  • Multimeter/DMM. There are various guides out there but I think there's an Extech that's a commonly recommended entry level DMM.
  • If they're into old shit aka carburetors grab an ultrasonic cleaner.
  • Flex head ratchet in your favorite size.
  • Snap ring pliers
u/DrunkBeavis · 3 pointsr/HomeImprovement

Both of those screw guns are for drywall. Those aren't the best choice for building a fence, or really anything except drywall. It might work, but it's going to make it more difficult. Any chance you can return those tools and pick up an impact driver like THIS?

As far as screw lengths, if you're planning on toenailing the screws, you could probably get away with 2" screws, but longer will be better. I would use 1-1/2" for the pickets.

Instead of toenailing the 2x to the 4x, you might have better luck with a bracket like THIS. You could also use shorter screws that way, so your tools might work better.

u/i7-4790Que · 3 pointsr/Tools

>I really wish Makita had found a way to go with a M12/bosch style

they did.

https://www.amazon.com/Makita-DT01W-Lithium-Ion-Discontinued-Manufacturer/dp/B004HEY0BU

problem was that Milwaukee bullied them out of the 12V market with patent lawsuit BS. So they had to make a new 12V line with a different battery style.



u/Sphingomyelinase · 3 pointsr/DIY

I tend to only buy screws with the torx/star bit pattern, as I've never had issues after driving (and removing) at least 1000 3" screws. Even with cheap battery drills.

That being said, for lag screws or even long philips head screws, what you're seeing that's like knife-through-butter is an impact driver. They're low RPM/high torque, but annoyingly loud.

Here's the one I just got and it will drive about anything:
https://www.amazon.com/Makita-XDT111-Lithium-Ion-Cordless-Impact/dp/B01L8O0CL8/ref=sr_1_1?ie=UTF8&qid=1498096142&sr=8-1&keywords=makita+impact

u/bassjam1 · 3 pointsr/Tools

If you plan on driving screws more often than drilling holes, I'd recommend an impact driver instead of a drill/driver. I have the 18v Bosch combo kit: impact and drill/driver, and I find that I use the impact weekly but the drill only gets used every now and then.

https://www.amazon.com/Bosch-PS41-2A-12-Volt-Lithium-Ion-Batteries/dp/B003LST02W

Getting both in a kit isn't much more.

https://www.amazon.com/Bosch-CLPK22-120-Lithium-Ion-Batteries-Carrying/dp/B005GT0IWK

As far as brands, it's hard to go wrong with Bosch, Makita, DeWalt and Milwaukee. Pick whatever has the best price this week.

u/Numl0k · 3 pointsr/Justrolledintotheshop

Derp, I didn't see the in/lbs versus ft/lbs... I knew something didn't add up...

Still, I'm impressed.

Edit: Check out the new brushless Impact Driver. 121 ft/lbs (1,460 in/lbs)! Take that, Model T!

u/sirBurdack · 3 pointsr/woodworking

I would say the bigger the more dangerous. Most often the threads will not break and you'll be left with a bolt/nut digging into whatever it is that you're anchoring. I have two DeWalt impact drivers: both cordless 20volt, one with approximately 160 Nm and a 1/4" chuck, the other is a 1/2" drive high torque driver with a maximum output of approximately 950 Nm. I've snapped grade 8 half inch lag bolts with the big one.

All in all I would suggest for standard use a 1/4 inch chuck, not drive, light duty impact wrench. Anything you feel might not be tight enough go ahead and use a socket and ratchet wrench to confirm and you should be all good.

DEWALT DCF887B 20V MAX XR Li-Ion Brushless 0.25" 3-Speed Impact Driver https://www.amazon.com/dp/B0183RLW8A/ref=cm_sw_r_cp_apa_PleoybVS9H9CS

Source: I work in heavy construction

For anyone curious, this is the "big brother" - DEWALT DCF899HB 20V MAX XR Brushless High Torque 1/2" Impact Wrench with Hog Ring Anvil https://www.amazon.com/dp/B00WTQW7JA/ref=cm_sw_r_cp_apa_ioeoybRH1MZTV

u/groverAlthouse · 2 pointsr/electronic_cigarette

Hahah.. um, this?

u/BunnehZnipr · 2 pointsr/BuyItForLife

MAKITA FTW. I have one on these, and it drives these screws and much longer ones ones all day long without issue. it's very ergonomic, and the batteries charge DAMN quick! I have had it (and a full set of their other products) for around four years, and with daily construction use they are still kicking ass. ...they don't look quite so pretty anymore, but that's user error =P I will make one note though,the Lithium Ion batteries do have a limited lifetime, using them full time like I have they lasted me for two years each.

u/mrrp · 2 pointsr/DIY

There's no free lunch, so yes, you will be wearing out the parts in the clutch. The question is whether or not the clutch was designed for that type of use or whether it was designed to occasionally save your butt when you accidentally apply too much torque to a fastener. I think it's almost certainly the latter.

I think you'd really like an impact driver.
http://www.amazon.com/Bosch-PS41-2A-12-Volt-Lithium-Ion-Batteries/dp/B003LST02W

u/Niyok · 2 pointsr/fixit

If the previous doesn't work try an Impact Driver. https://smile.amazon.com/dp/B01F5XOFFM

u/smittyjones · 2 pointsr/Tools

I have the M12 Fuel driver. I've had it for about a year and a half I think and haven't had any problems. A single battery will last about a week with the brushless impact driver.

But Makita also has a pretty nice setup, not quite as powerful and they're brushed, so not as "fuel efficient," but they are a little bit smaller than the M12 driver.

u/mousehorse · 2 pointsr/HomeImprovement

I prefer my corded one to my battery one.

http://www.amazon.com/Makita-6952-2-3-Impact-Driver/dp/B000140B4A

It just depends on what kind of projects you do. I tend to go long periods of time between big projects and batteries get in the way.

u/Mr_Dakkyz · 2 pointsr/Tools

Stanley Proto J7099A 13 Piece 3/8" Drive Hand Impact Driver Set https://www.amazon.co.uk/dp/B002C5ONG8/ref=cm_sw_r_cp_apa_eGyaCbR11Y8HS

u/skud8585 · 2 pointsr/DIY

The new 20v li-ions might change your mind about batteries. I have a 20v li-ion brushless impact. It is amazing, and being an impact it is easy to stop at a certain depth plus you don't need to mess with chucks to switch bits, it pops in and out easily.

u/grunthos503 · 2 pointsr/Tools

Looks like you do.

https://www.amazon.co.uk/dp/B002C5ONG8

May just take a little more searching.

u/Bauxitic_Fish · 2 pointsr/BeginnerWoodWorking

DEWALT 20V MAX XR Impact Driver Kit, Brushless, 3-Speed, 1/4-Inch, Tool Only (DCF887B) https://www.amazon.com/dp/B0183RLW8A/ref=cm_sw_r_cp_apa_i_2uWVDbGAZT27M

Get this get some bateries keep improving your xr lineup. Theyre good tools they will last you years and actually work for you.

u/AverageAlien · 2 pointsr/MechanicAdvice

I use a small 12v impact driver (brushless is better since it doesn't get weaker over time as contacts get dirty).

Or I use my 12v ratchet

This is my favorite set of wrenches They are long, have swivel heads and the way the ratcheting part protrudes on one side makes all the difference in a ton of situations.

u/Syren__ · 2 pointsr/projectbike

Here, check out this video for the chisel and other methods: https://www.youtube.com/watch?v=R5d0Bgvjmlk


I second what /u/DC_Farmboy said about the impact driver. It probably wont help you for the bolt that is already stripped but it is a valuable tool when working on these older machines. Also, i would just hit that bike with a power washer or a hose and some degreaser. You are going to be taking it all apart anyway, a little more water wont harm it.

Edit: Just read what you said about the power wash. If you stick a shop towel in the carb intake and use a fan tip on the power washer i doubt you would disconnect or break the wires

u/GunForHire · 2 pointsr/DIY

Lifetime tradesman here. Makita builds great saws, but their drills are not up to par. They have had many issues over the years with the most recent being charger issues. The chargers have/had a faulty fan in them that would not keep the charging unit cool enough charge. Love Makita saws.... Hate Makita drills. Anyone who says differently is misinformed or has not used drills on a daily basis.

Dewalt is still fine. The premiere tool for driving screws is the impact driver. And the Dewalt 18 volt impact driver is literally 'bombproof'. There is no finer screw driving device than this.

I have a friend who works in a service center that services all brands of tools. He says that, short of being run over by a cement truck, this dewalt driver cannot be destroyed. I own 2.

I am not a Dewalt enthusiast. Some of their stuff is junk, but their drills beat Makitas hands down.

u/Sophias_dad · 2 pointsr/MechanicAdvice

TBH, I'd just drill the heads off, in your position. something like 1/4" diameter is all you need, and you only need to go in maybe 1/4" before the head will pop off. You don't even need to worry about messing up the rotor since you are replacing it.

I'm pretty sure the impact screwdriver that people are mentioning here is not something you can get at home depot. Rather, its this very simple thing you whack with a small sledge that simultaneously uses the hammer's impact to hold the bit in the screw and gives the screw a tiny turn. [Edit]: I have used them many times for Honda rotor screws. Pretty much the only reason I have one.

Here's a sample...
https://smile.amazon.com/ARES-70006-Reversible-Applications-Disengage/dp/B01F5XOFFM/ref=sr_1_1_sspa?s=power-hand-tools&ie=UTF8&qid=1541261270&sr=1-1-spons&keywords=impact+screwdriver&psc=1

u/aDDnTN · 2 pointsr/motorcycles

you may have been using tools that seemed to fit, but i doubt you were using the right tools the right way if you ended up like this. Soft bolt materials aren't the issue.

You need to use a hand impact driver. I'd be surprised if you heard of it, let alone had one and used it correctly. But every professional mechanic has one and uses it when needed.

u/Hap-e · 2 pointsr/buildapc

I'm sure it sounds like a joke but I used this to put my PC together and I absolutely recommend that you don't do the same.

https://www.amazon.com/gp/aw/d/B074BHJQB3?psc=1&ref=ppx_pop_mob_b_asin_title

u/Retserof_Mada · 1 pointr/guns

As a last resort, before you strip the screw heads, use one of these, and dip your apex tip in some lapping compound.

Seriously, only as a last resort, because if it doesn't work you'll have to drill them out when the inpact slips and skips.

u/suckmywakelol · 1 pointr/Justrolledintotheshop
u/ramses0 · 1 pointr/homeowners

Yeah... I am trying to go battery-free for my drills / drivers (except for my little dinky B&D I linked above). This looks like "the one" -

http://www.amazon.com/Makita-6952-2-3-Impact-Driver/product-reviews/B000140B4A/ref=dp_top_cm_cr_acr_txt

...unfortunately still $150, and kindof a specialty thing. Maybe I can sell all my junky cordless drills and put some of that money towards this one.

--Robert

u/Fat_Head_Carl · 1 pointr/Tools

> I own the Hitachi DS 18DSAL, that takes the BSL1815X 18v, 1.5Ah battery.
>

I was considering this impact driver: https://www.amazon.com/gp/product/B00N3W7122/ref=crt_ewc_title_dp_2?ie=UTF8&psc=1&smid=ATVPDKIKX0DER


I'm definitely a "regular sized folk" :-)


u/mazizzo · 1 pointr/pics

These things are epic as hell. It probably won't last 19.5 years, but for the price, they're AMAZING. Use em at work all the time and they power through almost anything.

Plus they're like pocket sized.

u/AAA515 · 1 pointr/mechanic

Alright, no offense to the first commenter but we need to clearly define what we are talking about.
There isn't an "impact driver drill" I believe your talking about something like this that is a cordless electric 1/4" impact driver. It accepts 1/4" hex driver bits notice the special cut out at the base of the bit, that's what keeps it from falling out. It functions like a drill/driver until it encounters sufficient resistance then it impacts, giving increased torque(rotational force), it does not produce a hammering force(along the axis of the bit).

Now this is an impact wrench it too functions like a drill/driver until it meets resistance then it impacts adding rotational force but not hammer force. What are the differences between this and the driver we looked at earlier? First is obviously size, the wrench is bigger, and stronger, and heavier. But that's not what makes it a different tool, what makes it different is the tip, it's a square, like for putting sockets on, in this case 1/2" sockets but they make 3/8", 1/4", 3/4" and much larger!

So could you use the first tool in place of the much larger second tool? Yes! Use one of these adapters

Here's the problem tho, the first tool, the driver, makes at most 117 ft-lbs, and I believe that's stretching, the second tool, the wrench, makes 700 ft-lbs. To remove a rusty, crusty, stubborn lugnut you will need the bigger badder tool, sometimes it still won't be enough, and you'll need a breaker bar with a cheater pipe.

Now what the other commenter mentioned, the hammering force, that can be made with a few different tools. Let's start with the handheld impact driver yes it's confusing, two different tools, both called impact drivers, but this one we'll call the handheld, you hold it with one hand, and hammer it with a hammer. It has a cam mechanism that takes some of that axial force and imparts a slight (like 1/16 of a turn) rotation. It's good for stuck screws especially Phillips heads.

Another, more common tool is the hammer drill it is essentially a drill, it grips with three jaws onto the same bits as our first impact driver, or onto completely round bits, like your common drill bits but when you engage the hammer mechanism it will push its chuck forward and back rapidly, and the pressure you apply to the back of the drill hammers the bit into the material your drilling, useful for concrete/masonary work. But for real drilling power into concrete you want an SDS rotary hammer drill this bad boy only accepts SDS bits, provides it's own rotary and axial forces and will drill thru reinforced concrete like non reinforced butter.

Ok I think that about covers it, if anyone would like to add on I'd appreciate it. And remember:

Always use the right tool for the job, a hammer is the right tool for every job, and every tool can be used as a hammer!


Obviously that was sarcasm.

u/squid_fart · 1 pointr/DIY

This is my favorite drill for around the house use, it's lightweight and compact yet still has a good amount of power. The two you linked are hammer drills and are way overkill for the usage you described.

u/BLSully · 1 pointr/motorcycles

Nice list!

I'm also a non-professional mechanic, but here are my additions:

> Dead-blow hammer http://www.amazon.com/TEKTON-3188-Dead-Hammer-3-Pound/dp/B000NPT648/

> Impact Driver http://www.amazon.com/Pro-Grade-19620-2-Inch-Driver-Impact/dp/B002O16UPM/ - This + the dead blow hammer will save you a lot of stripped Phillips (or JIS) screws on older bikes.

> Carb Sync Tool http://www.650ccnd.com/mano.htm - This is one you can probably live without, and you can buy something pre-made, but the cost-functionality ratio can not be beat on this one

u/Sketchin69 · 1 pointr/Calgary

I believe my adapters came in a Dewalt kit that had a bunch of various things in it...

Basically these... https://www.amazon.com/3-Piece-Adapter-DW2541IR-DW2542IR-DW2547IR/dp/B01M7PNH4L

u/strong_grey_hero · 1 pointr/HomeImprovement

I love these Bosch 12V tools (I'm sure there's other manufacturers as well). Sure, you may need an 18V if you're bolting lag screws into framing lumber all day everyday, but you can't beat these little powerhouses when it comes to being convenient, light, and always having power.

u/shortyjacobs · 1 pointr/HomeImprovement

So DeWalt, Milwaukee, Ridgid, and Ryobi have been suggested. I say Bosch. this one, specifically

It does both 1/4" hex (screw driver bit), and 1/2" socket drive on th same tool, 140 ft lbs of oomph will break loose lug nuts with ease, but select down on the "tool power selector thingie" and you can feather in screws with precision as well. I'd buy another in a second if mine ever died.

edit: way cheaper as a bare tool

u/fuddinator · 1 pointr/aviationmaintenance

Looks awesome! Puts my box to shame. Only suggestion would be look into an impact driver to match with your drill. Works fantastic on panel screws. Even ones put in with gorilla torque and then some. Worth its weight in gold.

https://www.amazon.com/Bosch-PS41-2A-12-Volt-Lithium-Ion-Batteries/dp/B003LST02W

u/RabidBlackSquirrel · 1 pointr/sysadmin

My reciprocating saw and table saw in my home shop are Ryobi. Good value, been beating on them for a few years and they run fine.

This is my single favorite Bosch tool though, impact driver/wrench in one. Won't do lug nuts or anything crazy but for light/medium duty it's wonderful.

u/pegged50 · 1 pointr/mildlyinteresting

What's the big deal. They still sell those I have one in my garage. Does what it's supposed to do

u/jbrady3324 · 1 pointr/Tools
u/Alorithin · 1 pointr/electricians

M12 baby impact


Lightweight and small; a better version of those chinsy "powered" screwdrivers.


Otherwise, makita/dewalt/milwaukee/bosch will all be a good purchase and last 2 or so years depending on how hard they get used.





u/Yaethe · 1 pointr/Tools

A screw gun, what I think you're calling a wrench, a driver... local names for a global tool.

One of these

It's like a drill, but it hits it sideways to help really drive in screws, nuts, and bolts. Do not use it for drilling holes through, the jolting from those sideways hits will cause the drill bit to break.

u/1new_username · 1 pointr/HomeImprovement

I would get this:

https://smile.amazon.com/DEWALT-DCK240C2-Lithium-Driver-Impact/dp/B00IJ0ALYS/

I have that set and I use the impact driver 90% of the time. It is lighter, smaller (easier to fit in tight places) and more powerful. I pretty much only use the "regular" driver from the set when I have a special bit that won't work with the impact driver.

Edit: I actually just realized I have this brushless impact driver:

https://smile.amazon.com/DEWALT-DCF887B-Li-Ion-Brushless-3-Speed/dp/B0183RLW8A/

but the "regular" driver from that set. Brushless generally gets a bit more life out of a battery, not a ton of other difference.

Also, you can do most exterior work (drill into brick, concrete, etc) with the impact driver and the correct bit(s) (or the other driver and correct bits). I've put in concrete anchors in slab, drilled holes to mount things in a brick wall, etc with pretty much the first set I linked.

u/everyonestolemyname · 1 pointr/DIY

DeWalt makes/sells 60V batteries for their FlexVolt tools, they also have a higher amp hour rating when used on 20V tools - meaning they last longer.

I'm an electrician, and I use all Dewalt 20V XR tools, love em, absolutely zero issues. I've been pounding holes with a 2" holesaw and 7/8" auger bit at work and my 4 amp hour batteries last pretty long imo. I've also had a bunch of my power tools for years, so I'm a fan of the quality, especially since I drag mine through the dirt, drop them, get them wet, and I've flown with them a lot.

You definitely do not need FlexVolt tools, as a homeowner/casual DIY'er it's overkill, do not let anyone try to sell you that. It's a waste. Hell, the XR tools are probably more than enough, bordering on "might be more than you need". The regular 20V stuff is good enough for around the house.

As for the other brands, people are going to obviously point out Milwaukee and piss themselves like an excited dog going on about their stuff, personally I find it overhyped. While it's good, and I've used a bunch of their stuff, I still like my DeWalt. Also, usually it's pretty expensive - but when I compare prices I'm usually looking at their higher end stuff (M18 Fuel).

Makita is nice, not a lot of people use it, I'll leave it at that.

People say Ryobi is good for around the house, but I've always thought of their stuff as bargain bin tools. You buy it when you're broke and need a drill to do something, and might use it twice a year.

Rigid has a reallllly good warranty, their tools aren't half bad. I'd recommend them over Ryobi and Makita any day. Worth mentioning that Home Depot usually has "Rigid Days" or something where they have really good deals.

To sum it all up: Milwaukee is overhyped imo, DeWalt till I die, who uses Makita? lolRyobi, Rigid is also good. So DeWalt or Rigid.

Obviously batteries are always going to keep changing. It's bound to happen. They're constantly developing new and better technology so it only makes sense.

Also, I should have pointed this out first... You can still get DeWalt 18V tools on Amazon...

Here's the saw: https://www.amazon.ca/DC390B-Bare-Tool-18-Volt-Cordless-Circular/dp/B002VWK5RI/ref=sr_1_1?crid=1X0DARJY06Y35&keywords=dewalt+18v+circular+saw&qid=1556835828&s=gateway&sprefix=dewalt+18v+circu%2Caps%2C168&sr=8-1

Here's the impact: https://www.amazon.ca/DC825B-Bare-Tool-18-Volt-Cordless-Battery/dp/B002RT7K4Q/ref=sr_1_1?keywords=dewalt+18v+impact&qid=1556835851&s=gateway&sr=8-1

Apologies if you're not Canadian, but the US Amazon should have them as well.

u/fishymamba · 1 pointr/MechanicAdvice

Very easy to do a rotor and pad job yourself. Does require a couple of tools though. Even with the tools you'll be saving a bunch of money.

Changed the front brakes on my sister's civic for less than $150 dollars for the parts.

Besides sockets and a ratchet, you'll want to either get a C-clamp or a a brake caliper tool: https://www.amazon.com/Lisle-24400-Disc-Brake-Spreader/dp/B0002SQU9K

Also some brake lubricant: https://www.amazon.com/Permatex-24129-Silicone-Extreme-Lubricant/dp/B01L1LV9F6/ref=sr_1_11?s=automotive&ie=UTF8&qid=1496554333&sr=1-11&keywords=brake+lube

And sometimes its tough to take the rotor screws off, for that you will need an impact driver: https://www.amazon.com/gp/product/B002O16UPM/ref=oh_aui_search_detailpage?ie=UTF8&psc=1

Since your car is pretty new, you might not need the impact driver unless your rotors are rusty.

I used this rotor + pad set for the car : https://www.amazon.com/Power-Stop-K1043-Evolution-Drilled/dp/B005FKMOWM

I've put powerstop rotors and pads on 4 cars now and they have worked quiet well. Some people were saying that the drilled rotors are prone to cracks, but that won't happen for a daily drive car on the street. Other rotor and pad options:

https://www.amazon.com/Wagner-BD125669E-Premium-Coated-Brake/dp/B00HJJDSZO

https://www.amazon.com/ACDelco-17D914C-Professional-Ceramic-Front/dp/B000IYY7PW

Rears will be different than the ones I posted, so check and see what will fit. Amazon makes it pretty easy, just enter your car and it'll tell you what fits.

Since you have watched videos on the change, I don't think you need me to tell you how to do it.

u/fireguyy · 1 pointr/HomeImprovement

I've had the same DeWalt drill for 10+ years and its still going strong, but my wife gave me this DeWalt impact driver and it's amazing.

https://www.amazon.com/dp/B0182AN2Y0/ref=wl_it_dp_o_pC_nS_ttl?_encoding=UTF8&colid=TCFD7W74T80Y&coliid=I1A6Q2DAYJHMUK

u/mr_hamilcar · 1 pointr/HomeImprovement

This drill:

DEWALT DCF887D2 20V MAX XR Li-ion 2.0 Ah Brushless 0.25" 3-Speed Impact Driver Kit https://www.amazon.com/dp/B0182AN2Y0/ref=cm_sw_r_cp_api_sDlXBbJBN76MP

u/shluap · 1 pointr/DIY

I use my: http://www.amazon.com/Makita-XDT08Z-Lithium-Ion-Brushless-Cordless/dp/B00GG0I2TE/ref=sr_1_1/185-0258266-6741125?ie=UTF8&qid=1417740089&sr=8-1&keywords=Makita+Impact+Driver#productDetails
for pretty much every bolt on my cars and it rocks, one of the best tools I have owned actually, if you come across this guy get it totally goes toe to toe with my pneumatic and I never get that out anymore because usually I am just using it to speed things up and getting the compressor and hose out is a hassle comparatively. Haven't used the dewalts very much.

u/ThurstonHowell3rd · 1 pointr/DIY

Get one of these and a hammer.

u/RogueJello · -1 pointsr/Tools

Getting the numbers off Amazon spec sheets. I see the weight on the 18V Impact Driver, but not the new one. Having lifted one in the store it appears to be similar in weight.

DCF887: 2.4#
https://www.amazon.com/DEWALT-DCF887B-Li-Ion-Brushless-3-Speed/dp/B0183RLW8A/ref=sr_1_1?ie=UTF8&qid=1522688641&sr=8-1&keywords=DCF887

DC825B: 2.2#
https://www.amazon.com/DEWALT-DC825B-18-Volt-Cordless-Package/dp/B002RT7K4Q/ref=sr_1_6?ie=UTF8&qid=1522688604&sr=8-6&keywords=18v+dewalt+impact+driver

Note this is for just the tool. As I said, the Lithium battery appears to be 1# lighter, but I could just buy new batteries for far cheaper.

I see your point about the better power, but I've yet to encounter anything that it struggled with, and I've done just about everything but metal working or car repair.

You're also mistaken about the lights. Not sure if it's LED or not, but there's at least one bulb.

Brushless vs Brushed is nice, but I don't think it gets me much. First, it makes the tool more efficient, but I can just switch batteries. Second, it increases the lifespan of the tool, but I don't care if I'm replacing it before it wears out.