Top products from r/moped

We found 23 product mentions on r/moped. We ranked the 66 resulting products by number of redditors who mentioned them. Here are the top 20.

Next page

Top comments that mention products on r/moped:

u/cluecheck · 1 pointr/moped

It's easy lift the frame, don't remove back, just the front long bolt. Stick the front wheel in a milk crate. I can have a carb in and out pretty quickly.

Where is this airleak? I've never had a prob with an airleak at the carb on any of my hobbits...and i've owned a bunch of them.

Try this stuff: http://www.amazon.com/Permatex-80062-High-Gasket-Sealant/dp/B000HBGHB8/ref=sr_1_2?ie=UTF8&qid=1407247928&sr=8-2&keywords=gasket+sealant (you can get at local autostore)
from the intake of the cylinder to the intake itself, from intake to carb.\
It's also great for base gaskets too! Creates a good gas resistant seal, while not being permanent for easy removal later. Better then silicone crap that just squeezes out of the mating area.

IMO, the phva is just going to run like shit on a hobbit. The stock carb pushes the best velocity of gas/air to that cylinder on a hobbit.

Also not having an airfilter could potentially cause problems by not have any back pressure. I've always ran the stock airbox with my stock carb other wise, they would run like shit.

u/Elrathias · 1 pointr/moped

Cant find any specs for a VM14 or VM14SH, but it should get you 1. great mileage and 2. awesome low end power, assuming its re-jetted correctly, or using a adjustable jet.

Your not going to have much top speed though since it will probably be hitting max flow at about 7-8k rpm. (for 50->70cc that is, after all its a 40% normalized volume increase. in reality its much more because of how the bypass-puschback exhaust compression on a 2stroke works, but meh.)

here, have some reading:

http://www.mopedarmy.com/wiki/Carburetor

http://iheartstella.com/resources/manuals/tuning/Graham-Bell-Two-Stroke-Performance-Tuning.pdf (Page 93 and on, esp page 112 which illustrates the carb sizing i mentioned,, but really, this entire PDF is the GO-TO document of 2 stroke theory, setup and tuning. get the book if you dont like on-screen reading

u/eobanb · 3 pointsr/moped

Yep, I've got one and it works great for carrying one moped at a time (Express pictured, but I've also used it to carry other mopeds, including my Murray and my Hobbit). Front wheel off, use four ratchet straps—one on each corner. Here's another view of it.

Here it is on Amazon for $108.

I've had friends make their own custom ones but only because they want it attached to the car in two places, instead of just at the receiver. Any hitch-mounted carrier definitely wobbles a tad (although that's all within the design limits).

u/knightgreider · 2 pointsr/moped

Yeah I recommend just researching more. I knew nothing last January and built a custom battery for my moped the past 2 months.
Check out this book. It has everything I used for it. Plus he has YouTube videos. He doesn’t pay me for this. I was just enthusiastic enough to learn.

DIY Lithium Batteries: How to Build Your Own Battery Packs https://www.amazon.com/dp/0989906701/ref=cm_sw_r_cp_api_i_uekvDbPFXV23H

u/genericgamer · 1 pointr/moped

I use this bad boy. the fabric on the chain can take a beating. While the cable isn't very long I wrap it around the metal bar and my frame. When I have a bicycle rack available to me I'll use that. otherwise a stop sign pole does pretty good too. Visibility is important. Even where I live most people aren't going to steal a bike locked up under a big lamp. u/blank5tare's recommendation is pretty good too I've used that in the past.

u/andyleclair · 1 pointr/moped

Oh, that's great! Thanks a lot! I was reading this, but that's just engine.

u/Young_Maker · 1 pointr/moped

http://www.amazon.com/NGK-B6HS-Spark-Plug-Pack/dp/B0000BXHSP

The type is NGK B6HS. Taken straight from the moped army page. I betcha the'll have an equivalent at the auto parts store if you don't want to order from amazon.

u/tman67234 · 1 pointr/moped

POR 15 sells a kit that comes with different cleaners and a sealant. It's the longest lasting solution I have used. http://www.amazon.com/POR-15-Cycle-Tank-Repair-Kit/dp/B000H9K4JQ

u/xxmickeymoorexx · 1 pointr/moped

i have been planning on using a product called Kreem. seen a few decent reviews, but have not yet tried it myself.

u/cwerth · 3 pointsr/moped

I use one of these
Park Tool RT-2 Head Cup Remover for 1-1/4 and 1-1/2 - Inch Headsets https://www.amazon.com/dp/B000VY1QFI/ref=cm_sw_r_cp_apa_i_xL5FDb3DX7P69

u/BearBong · 1 pointr/moped

Woah shit. Maybe invest in one yourself then?