Reddit reviews Belkin Cord Concealer with Double-Sided Adhesive Tape (Gray, 6 Feet)
We found 16 Reddit comments about Belkin Cord Concealer with Double-Sided Adhesive Tape (Gray, 6 Feet). Here are the top ones, ranked by their Reddit score.
Cord concealer for floors and countertops hides unsightly cable clutterConceals cords to eliminate tripping hazardsFlexible material can be wrapped around corners and furnitureCan be easily cut to any desired length. Guards against fraying from foot trafficIncludes double-sided adhesive tape. Practical cable management solution for home or office
4 inches of this should do the trick, just glue or anchor it down on the outside of where the wheels will cross and you should be golden.
http://www.amazon.com/gp/aw/d/B00006HVLW/ref=mp_s_a_1_2?qid=1452788513&sr=8-2&pi=SX200_QL40&keywords=rubber+wire+cover&dpPl=1&dpID=41F1ZA0DVPL&ref=plSrch
Makes sense to have the cable cross where you have it but you will really wish you had this the day the lights are out and you trip over the cable yanking the cord at an angle causing damage to the port.
You could tape the cords to the floor/wall to make them less accessible, or you could buy some thick walled PVC pipe to put your wires in.
Or, you know, lock the dog in another area of the house with something else to chew on.
something like these?
http://www.amazon.com/Belkin-6ft-Cord-Concealer-Grey/dp/B00006HVLW/ref=sr_1_1?ie=UTF8&qid=1427227557&sr=8-1&keywords=floor+cable+cover
If you can't run them in the wall, zip tie them together and cover them with something that looks like this.
Belkin 6ft. Cord Concealer (Grey) https://www.amazon.com/dp/B00006HVLW/ref=cm_sw_r_cp_awd_ASA9wb7S69B5M
Best option is run them in the wall. All you need is a drywall saw, a couple low voltage plates, and maybe a glow rod if its an exterior wall.
OOOh. Icky. Ya don't do that. Although you might be able to get just a little cable concealer. That would still look better than hanging it.
>In between the couch and television is a walkway leading to the bedroom
That sounds like the worst idea ever.
In your situation, I would probably just run a cord along the floor and conceal/protect it with something like this.
If you don't have any other options but to run those cables across the door like that. I have used this in the past with good results.
It would be easiest to go over the door and run along the trim
To go in front of the door you'll probably use something like this
http://www.amazon.com/gp/aw/d/B00006HVLW/ref=mp_s_a_1_1?qid=1458599703&sr=8-1&pi=SX200_QL40&keywords=floor+cable+cover&dpPl=1&dpID=41F1ZA0DVPL&ref=plSrch
But it's not gonna look at that good and good luck getting it to stick to the ground and stay
There's also this stuff if it helps. Not sure what the opinion is on it around here.
Don't like these Cord Covers?
What about something like this over it?
https://www.amazon.com/Belkin-6ft-Cord-Concealer-Grey/dp/B00006HVLW/ref=sr_1_1?ie=UTF8&qid=1485819625&sr=8-1&keywords=cable+trip+guard
I approve, but probably throw something like this over it: https://www.amazon.com/Belkin-Cord-Concealer-Double-Sided-Adhesive/dp/B00006HVLW/ref=sr_1_10?ie=UTF8&qid=1503458635&sr=8-10&keywords=wire+concealer
Here is the mobile version of your link
Depends on how deep you need to bury the fiber. In the best case scenario, you can just leave loose-buffered fiber on the ground and put a cover over it: https://www.amazon.com/dp/B00006HVLW
Over 150 feet, this could be even cheaper for OP than a set of ubnt radios that can do 1Gb/s.