Reddit reviews Dayton Audio SA70 70W Subwoofer Plate Amplifier
We found 6 Reddit comments about Dayton Audio SA70 70W Subwoofer Plate Amplifier. Here are the top ones, ranked by their Reddit score.
Line-level and speaker-level inputs for connection to any systemAuto-on circuit comes on the instant the amp is neededVariable 2nd order low-pass crossover from 40 Hz - 180 HzProven performer at a low price point
There are less demanding ways of feeling the bass. I put a reasonable sized Buttkicker inside my recliner at my listening station and powered it with a modest Dayton Audio 100ish wpc sub amp. At half volume it scares the cat off my lap. At a much saner level, it enhances sub bass and makes it seem much louder than it really is. Bonus, feeling as well as hearing the bass makes it easier to note the changes in pitch and whether a bass note is from a synth or a drum. You can either use the 2nd sub output on your amp for convenient tuning with the remote, or use a y splitter if you have a single sub out.
Total cost including cables ~$210
Buttkicker mini $89
Dayton Audio amp $79 70 watt
Dayton Audio amp $106 100 watt
The 70 setup should be enough to shake an entire couch to annoying levels. The transducer is very efficient and creates a lot of furniture or desk chair vibration with very little power. The "whomp" when the sub amp powers on was enough to launch it 3 inches up in the air when I test fired it on my desktop.
Just get the Dayton Sub 1000 for $120 and you're set. If you're a handy fella you could put a plate amp in the samsung sub. Either way you need some amplification for you LFE channel.
Sorry I was under the impression you already knew since you knew since you knew the correct wires for it were in the back of the amp, but now I know that's obviously a characteristic of all plate amps. =) This amp and these shakers.
Okay, so you don't need HDMI inputs or anything? If so, the Denon is a huge overkill.
The sub will probably take the output from the receiver via RCA, and just have a standalone amp, without needing to pass the speakers through, since the receiver will probably have the crossover built in. You can use a plate amp, something like this.
By separate speaker sets, you mean that you've got sets you want to switch between, correct, not ones that you want to have on all at the same time?
I wanted to but I didn't. I will be rebuilding it. But I leaned some pro tips along the way. It's hard to make armrests stable. They like to wobble left and right. With a joystick, you want it to be solid at that point. Vertical screws through the x55 holes in the corners are nice.
I built in a tactile transducer with amp:
http://www.parts-express.com/aurasound-ast-2b-4-pro-bass-shaker-tactile-transducer--299-028
http://www.amazon.com/Dayton-Audio-SA70-Subwoofer-Amplifier/dp/B0002TUDKG
and it is absolutely essential. No way could I play without it any more!
You want a LOT of desk space. Room for mice. Remember that a standard keyboard is often wider than the space between armrests.
That's all I got. I ill be rebuilding mine soon.
I was in the same situation. I went with a Dayton Audio plate amplifier. Specifically this one:
http://www.amazon.com/Dayton-Audio-SA70-Subwoofer-Amplifier/dp/B0002TUDKG?ie=UTF8&psc=1&redirect=true&ref_=oh_aui_search_detailpage
My sub supports 130 watts rms @ 3 ohms so this is pumping 93 watts to it rms. It puts out plenty of bass for me. I probably could've gone with a less powerful amp, but it sounds great. It's quite large so finding somewhere to put it could be an issue, I hid mine behind a wall and ran wires to my sub behind my couch. They have a variety of models too at different price points:
http://www.amazon.com/gp/search/ref=sr_nr_n_3?srs=6401467011&fst=as%3Aoff&rh=n%3A172282%2Cn%3A%21493964%2Cn%3A281407%2Cn%3A172532%2Cn%3A11042061%2Cn%3A11042191&bbn=11042061&ie=UTF8&qid=1463738516&rnid=11042061