Reddit reviews Foreasy 3D Printer Tool 3D Print Removal Tool Enhanced Version Set of 2

You didn't specify if you bought a kit or fully assembled, but ill assume it's a kit ;)


-

1. Follow the online instruction. Grab yourself a laptop/tablet since online has higher res pictures and comments per steps.
   
   

• Before each step see the comments under them to see if others have had trouble or give their alternative insight on an issue.
  
  
  

2. When assembling it, make sure you are doing this all on a flat, even surface. I did this on my granite kitchen counter top just so i wont run into alignment issues during calibration
   
   
3. Once you have it built, calibrated and working, it is customary (per say) to print a 3D Benchy, to get insight if the printer needs any fine tuning.
   
   
4. Must have recommendation
   
   

• OMG get these e3d silicone socks!. I've had dozen's of successful prints and these socks have helped so much from preventing THIS
  
  
• If you plan to use exotic filament (eg: wood, metal, carbon fiber), GET A HARDENED STEEL nozzle. The stock BRASS nozzle (0.4mm) is only good on non-abrasive filament (eg: regular PLA+ABS)
  
  
• 3D Print Removal Tool Spatula
  
  
• Restock on PEI Sheets!. These are what are recommended by the community as per cost effective and reliability and i think shipping is ~$9? So get more than one for the future. The ones on amazon are !@#$ overpriced!
  
  
  
  
• (optional, didnt like the power cord being bent) Left Angle Power Extension Cord.
  
  edit: I found this on thingiverse to make the PSU cable left angled
  
  

5. Start learning (if you haven't) to use Fusion 360 (most preferred), 123D, or TinkerCAD to print you whatever creativity you have.
   
   AVOID SKETCHUP!!.
   
   
6. Once you have a successful working, printing machine, start printing replacement parts for your printer! As Josef Prusa has stated, it's ok to print the machines parts out of PLA, If you wanna go with something more durable, go for PETG. eSun PETG Orange is what i use. BUT FIRST, make sure you adjust the Slic3r setting and a few test prints to print parts in PETG since it's finicky to work it.

I'm at 2,000 meters of filament printed with my Maker Select, very happy with it, some tips:

-The Maker Select V2.1 is simply a re-brand and upgrade of the Wanhao Duplicator i3. You'll see that name "i3" thrown around more than Maker select, so just be aware they are nearly synonymous


-First, definitely get the blower fan upgrade: https://www.amazon.com/gp/product/B00MJU6JR2/ref=oh_aui_detailpage_o03_s00?ie=UTF8&psc=1
Buy two of them to have an extra in case of death


-Print out a blower fan housing for that fan: http://www.thingiverse.com/thing:1025471


The fan upgrade provides a huge improvement in print quality


-Get the all metal hot end from micro swiss: https://www.amazon.com/Hotend-Nozzle-WANHAO-FlashForge-Builder/dp/B01C3HEQZC


-THe "Z-Brace" mod reduces vibrations from the machines movements: http://www.thingiverse.com/thing:921948


Some people swear by it, but the print time for those parts is roughly 20-24 hours total. In my 2,000+ meters of print, I haven't bothered because of the print time, but still bought the extra pieces in case I decide to do it.


-I've been mass printing tiles for d&d too, I looked at openforge and decided against that line, but went with TrueTiles instead. https://www.youtube.com/watch?v=JUecWG1W-ss


Highly recommend truetiles over the other tile lines out there - the creator is a crafting genius (look him up on youtube - "wyloch"). They take less plastic, are more versatile, faster print time.


I found that Cura 15.04.x was much better than the recommended Cura 2.5.x. My setting for churning out tiles is something like 210C nozzle, 70 mm/s, 55C bed, 0.25 resolution, 0.8 shell, 10% fill, 2mm retraction, 20mm/s retract speed, 60mm/s travel speed, no brim/raft, no supports. You should print at resolution multiples of 0.04 (because of the way the filament feed gear works), ie. 0.08, 0.12, 0.16, 0.2, etc. I'm going to switch to 0.24 resolution for tiles. I do 0.12 for small figures. The printer can reliably print resolution 0.08 right out of the box (lower the speed to ~35 mm/s) but takes a long time to print.

-The black material on the heated bed is call Buildtak - be careful not to puncture it with the supplied putty knife. Get some blunt tools such as https://www.amazon.com/gp/product/B01A81FXMK/ref=oh_aui_detailpage_o06_s00?ie=UTF8&psc=1

-you don't need any tape, glue stick, hair spray, for buildtak

-Be sure not to use any acetone or alcohol on Buildtak - both will ruin it.

-Apparently you don't really even need to heat the bed with buildtak, the stuff is super effect with first layer adhesion running at room temp. I ruined my original buildtak by using the supplied putty knife to remove a print that was so super stuck to the bed because I kept it heated. Doesn't hurt to keep it heated though, but be aware heat + buildtak = much adhesion

-That slight lip on the butterfly's bottom layer is due to the settings of first layers being laid down slightly thicker than the others. Sometimes called "elephant's foot" it can also be caused by the nozzle being too close to the bed, which will smush those initial layers more than needed. Closer nozzle = more smushed first layer = better adhesion, but with buildtak you can get away with keeping the nozzle further away, and adjusting your cura settings for a first layer thickness equal to the rest of the print

Get some essential tools: those wire cutty clipper things (for cutting support structures off your prints) and a painter's scalpel for peeling prints off the heatbed.

Consider getting the upgrade kit for the ender 3 pro sometime; the flexible removable heatbed is a HUGE convenience for getting prints off and cleaning the heatbed.

https://www.amazon.com/gp/product/B072WS3M9H

This angle bend is EXTREMELY helpful. You don't have to get this specific product, but trust me that you want a tool like this.

https://www.amazon.com/dp/B01A81FXMK

The scalpel I bought isn't for sale anymore but this one looks good enough.

Seconding ChituBox, it's a lot better at supports and just overall usability.

Also, I've had zero issue removing prints from the plate by using a thin metal scraper. The one I've been using is here: https://www.amazon.com/gp/product/B01A81FXMK

The shorter one is perfect for getting under prints with a little bit of force.

Also, if you're using a standard putty knife on the bed: dont. Them edges be too sharp for the PEI to handle. I use something like this which saved my PEI from certain death a few times.

• Heat gun for melting off any stringing post print
  
• Small spatulas for those hard to remove prints
  
• These sanding tools on Thingiverse for sanding rough surfaces and cleaning up support contact areas

Wiki is: http://mpselectmini.com/

Some items I bought from Amazon (don't buy the hot end pieces if you have a V2. They changed the hot end to an all metal one):

https://www.amazon.com/gp/product/B00WE1A3D2/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1
https://www.amazon.com/gp/product/B00T2DNKJY/ref=oh_aui_detailpage_o01_s00?ie=UTF8&psc=1
https://smile.amazon.com/gp/product/B01LAYCRAA/ref=oh_aui_detailpage_o07_s00?ie=UTF8&psc=1
https://smile.amazon.com/gp/product/B00L4UXQ42/ref=oh_aui_detailpage_o08_s00?ie=UTF8&psc=1
V
https://smile.amazon.com/gp/product/B00MQKW230/ref=oh_aui_detailpage_o09_s01?ie=UTF8&psc=1
https://smile.amazon.com/gp/product/B01A81FXMK/ref=oh_aui_detailpage_o05_s00?ie=UTF8&psc=1
https://smile.amazon.com/gp/product/B01ACIFPYA/ref=oh_aui_detailpage_o00_s00?ie=UTF8&psc=1

I had something similar, but it wasn't beefy enough to pry the prints off the buildplate..

https://www.amazon.com/Foreasy-Printer-Removal-Enhanced-Version/dp/B01A81FXMK/

It totally flexed and slipped and cut my finger!

​

Re: plastic scraper that comes with the Photon: Arg- I guess I misunderstood, I thought that was for the buildplate. It's for failed prints in the vat! That makes much more sense.. I tried to use it on my first few prints and it totally failed

Link to the good bits. It's not done. I'm just not sober enough to handle a heat gun. Used a hair dryer and a "Blade" to see her face.

I have this here and never had any issues. Works great and gets anything off my PEI so far. https://www.amazon.com/Foreasy-Printer-Removal-Enhanced-Version/dp/B01A81FXMK/ref=sr_1_4?s=industrial&ie=UTF8&qid=1483558574&sr=1-4&keywords=3d+print+removal