Top products from r/pressurewashing
We found 14 product mentions on r/pressurewashing. We ranked the 14 resulting products by number of redditors who mentioned them. Here are the top 20.
1. Hardline Products HR-8061-2 Hour Meter/Tachometer for up to 2-Cylinder Engines,Black
Sentiment score: 1
Number of reviews: 1
Works with any gas engine up to two cylinders and 16,000 RPMAdjustable input for all types of ignitions, including fuel injected enginesHour meter shows total hours accumulated; hour/tach meter shows RPM's when the engine is runningEasy installation; no power or ground requiredInternal battery lasts...
2. TEKTON 6943 Precision Pick and Hook Set, 4-Piece
Sentiment score: 0
Number of reviews: 1
Heat treated, chrome vanadium steel shaftsCushioned, non-slip grips for extra controlKnurled shaft grip area for precise workIdeal for assembly, repair, or removal of small partsSet Includes: 1-pc. Full Hook, 1-pc. 45-degree, 1-pc. 90-degree, 1-pc. Straight PickHeat treated, chrome vanadium steel sh...
3. WD-40 Company 300012 Specialist Silicone Spray Smart Straw - 11 oz., Silver
Sentiment score: 0
Number of reviews: 1
Silicone lubricant provides a protective, waterproof and low-friction coating to multiple surfacesOur quick-drying formula cures into a clear, stain-resistant hard film that protects your surfaces from the elementsSafe to use on metal, rubber, vinyl, and plastic without a messy residueSMART STRAW S...
4. Coxreels 1125-4-200 Steel Hand Crank Hose Reel, 1/2" Hose I.D., 200' Hose Capacity, 3,000 PSI, without Hose, Made in USA
Sentiment score: 0
Number of reviews: 1
Please scroll down the page to the "From the manufacturer" section to see a detailed explanation of this product's featuresPlease watch the video at the bottom of the image list to learn more about key features of the 1125 Series hose reelClick on the enlarged image to see additional application ima...
5. Coxreels 10780 Hose Reel Reducer, 3/8" NPT Female x 1/4" NPT Male, 300 psi
Sentiment score: 0
Number of reviews: 1
Hose reel reducerReducer is used where the thread size of the entry device is smaller than the entry thread of the enclosure3/8" NPT female x 1/4" NPT male thread sizeNPT end fittingMaximum pressure 300 pounds per square inch
6. Pre-Cut Spiral Wrap Hose Protector, 3/8" I.D., 25' Length, Black
Sentiment score: 1
Number of reviews: 1
Temperature Range -60 to +175 Degrees FMade with Anti-Static and UV Protection AdditivesTolerates Acids, Oils, and Solvents
7. Sodium Percarbonate (Oxidizer) 10 Lb Pack (Consits of 2-5 Lb Packs) (9955)
Sentiment score: 1
Number of reviews: 1
Denture cleanerOxygen sourceActive ingredient in OxiClean and Tide
8. 9pc 5lb Dent Puller Slide Hammer Body Shop Repair Tool
Sentiment score: 0
Number of reviews: 1
9. Ultimate Washer UW16-PW70B3 Adjustable Soap and Chemical Injector Pressure Washer, 3/8-Inch
Sentiment score: 0
Number of reviews: 1
Soap and Chemical Injector, 200 Degree, Pressure Washer requirements 2000-4000 PSI, 2-5 GPMWorks with Standard3/8-Inch Quick Connect Pressure WashersPressure Washer Chemical Injector Kit Includes Injector, Tubing and FilterAdjustable Control Metering Valve; Used for Cold or Hot Water ApplicationsBla...
10. Geekpure Whole House Big Blue Water Filter Housing 1-Inch Outlet/Inlet with Wrench and Bracket -4.5 Inch x 20 Inch - Clear Housing
Sentiment score: 1
Number of reviews: 1
Complete set 20 inch big clear housing,1"NPT inlet/outlet,with plastic wrench,screw and metal bracket.Clear housing allows you to see when you need to change filters and everything else works as it should.Housing only, filter cartridges are sold separately .Fits all standard sized 4-1/2 inch diamete...
11. EFORCAR Electric Car Washer, High Pressure Car Washer Pump,12V 80W Electric Washer Pump Car Washer Device for Auto,Pet, Window,Watering and Camping (Car Washer)
Sentiment score: 0
Number of reviews: 1
★ HIGH PRESSURE:This car washer carry a 80W High-power pump,can provide much more pressure when you washing your love car. Flow (Max.): 5.5L/min,can let you enjoy the fun dripping of Washing.★ ENERGY,WATER SAVING:Motor power can suitable for vehicle-mount,no need to turn on the car,it can wash,n...
12. Annovi Reverberi Pressure Washer Replacement Pump, 2.5 Max GPM, 3000 PSI, RMV25G30-EZ, Easy Start
Sentiment score: -1
Number of reviews: 1
Maximum psi: 3000Maximum gallons per minute: 2.5 GPMRotations per minute (RPM): 3,400Shaft direction: StandardStart style: EZ Start
I'd go with this one
The one I use is different but I'll be using these in the future, they seem to be better quality, and the ones I use seem to read the RPM incorrectly (though it may be because it's a 2 cylinder).
I wouldn't worry about it, if the pump says an 8hp is fine, then it should be okay. I would let the engine run for an hour or two without the pump to let it break in.
I have a screen filter first then a 20" clear housing filter with a bleed valve like so:
Geekpure Whole House Big Blue Water Filter Housing 3/4 Inch or 1-Inch Outlet/Inlet with Wrench and Bracket -4.5 Inch x 20 Inch - Clear Housing https://www.amazon.ca/dp/B077BDQGHP/ref=cm_sw_r_cp_apa_i_Q-fnDb0NJWZZD
I use the bleed valve when I see air in the filter. Everything gets filtered down to 5 microns before entering my pump. Have to change it 3 or so times a season.
It is not a high quality machine, but the accessories look ok for 180 bucks.
Brass threads, etc.
Do yourself a favour and get some of this to wrap around the hose.
https://www.amazon.com/Pre-Cut-Spiral-Protector-Length-Black/dp/B00OA3XJKQ/ref=pd_bxgy_3/139-8073179-4205507?_encoding=UTF8&pd_rd_i=B00OA3XJKQ&pd_rd_r=787d57cd-a86e-11e9-bb72-ada5d458be15&pd_rd_w=bjeSK&pd_rd_wg=5TLl8&pf_rd_p=a2006322-0bc0-4db9-a08e-d168c18ce6f0&pf_rd_r=8YXJ4FF5DJDGM9Z6PYGB&psc=1&refRID=8YXJ4FF5DJDGM9Z6PYGB
Or see if you can scab a metre or two from a hydraulic hose supplier just for the bit of hose closest to the machine where it rests on the ground.
i picked up a tub of oxiclean but im sure ill need more. i just couldnt find the ratio that people used. i was going to order something like this from amazon if i could - https://www.amazon.com/Sodium-Percarbonate-Oxidizer-Consits-Packs/dp/B00OKOFUZM/ref=sr_1_4_a_it?ie=UTF8&qid=1492086501&sr=8-4&keywords=sodium+percarbonate
its rough cut cedar, would the turbo be ok on that or just a regular fan tip?
I'm reading petroleum jelly will dry out o-ring if it's rubber (not sure what mine is, haven't looked)
I do have WD-40 or this silicone spray. I'm thinking maybe the silicone spray?
Alright so, what you've got there are M22 couplings -- for simplicity's sake, let's call the side with the external threading M22-A and the side with the spinning nut M22-B.
The issue is that the standard internal size is 15mm (that's the width of the stem on part M22-B and of the hole it slides into on part M22-A), but chinese machines and accessories often use 14mm for some stupid reason, causing all sorts of incompatibilities. It's a very frequent issue.
The problem you're gonna be facing if you order kits like the one you linked is that it'll only ever fit one of your connections. Instead, consider these adapters:
Obviously you shouldn't order those packs of 50 units, but they are actually the correct parts. If you look around with the part numbers I gave you, you should find them pretty easily.
http://www.amazon.com/gp/aw/d/B0078RRO34/ref=mp_s_a_1_14?qid=1462987384&sr=8-14-spons&pi=AC_SX236_SY340_FMwebp_QL65&keywords=hose+reel+gp&psc=1
Had it for quiet some time. It's fairly solid.
Attach downstream injector after the pump, but before the pressure hose. Cheaper injector, but should work for about anything most people want to do. If you want to clean dirty stuff faster, order the hi draw fixed injector online. If you want to REALLY clean dirty stuff REALLY fast, order an Xjet, or a SuperSudsSucker from Envirospec.
Link to normal downstream injector that will get you up and going: https://www.amazon.com/Ultimate-Washer-UW16-PW70B3-Adjustable-Chemical/dp/B01N6JT8XZ/ref=mp_s_a_1_1?keywords=downstream+injector&qid=1556070416&s=gateway&sr=8-1
Thanks for the help. I think I have the right item but the pressure rating is a problem, it says its only 300 psi. Is that ok or do I need to find something else?
What would you think about this? Instead of buying another OEM pump, I purchase a RMV25G30-EZ
Its a plunger pump with a 5-year warranty. Cost: $110.
Any thoughts as to compatibility and whether this is still a bad idea? This is for occasional home use, not commercial. Open to other manufacturers if OEM is a turd pump.