Reddit reviews TEKTON 6943 Precision Pick and Hook Set, 4-Piece
We found 11 Reddit comments about TEKTON 6943 Precision Pick and Hook Set, 4-Piece. Here are the top ones, ranked by their Reddit score.
Heat treated, chrome vanadium steel shaftsCushioned, non-slip grips for extra controlKnurled shaft grip area for precise workIdeal for assembly, repair, or removal of small partsSet Includes: 1-pc. Full Hook, 1-pc. 45-degree, 1-pc. 90-degree, 1-pc. Straight PickHeat treated, chrome vanadium steel shaftsCushioned, non-slip grips for extra controlKnurled shaft grip area for precise workIdeal for assembly, repair, or removal of small parts
These, the rounded hook worked the best. After letting them soak in bleach water I used that one to go underneath or the middle and pluck them off. Not easy and is a long process, but worth it at least for me. Lol
TEKTON 6943 Precision Pick and Hook Set, 4-Piece https://www.amazon.com/dp/B000NPPBQK/ref=cm_sw_r_cp_api_i_MgPLDbBANYS6Y
Get a pick set, DO NOT use a screw driver to remove seals, bushings or wipers. Any brand will do. https://www.amazon.com/TEKTON-6943-Precision-Pick-4-Piece/dp/B000NPPBQK/ref=asc_df_B000NPPBQK/?tag=hyprod-20&linkCode=df0&hvadid=309807921328&hvpos=1o1&hvnetw=g&hvrand=7008630978416797227&hvpone=&hvptwo=&hvqmt=&hvdev=m&hvdvcmdl=&hvlocint=&hvlocphy=9010792&hvtargid=pla-384727962388&psc=1
Always use the right tool for the job
Small flat blade screw-driver for easy ones.
Hook & pick set for normal ones.
https://www.amazon.com/TEKTON-6943-Precision-Pick-4-Piece/dp/B000NPPBQK/ref=sr_1_3?keywords=seal+pick&qid=1557633662&s=gateway&sr=8-3
Long wood screw and slide-hammer dent puller for stubborn ones
https://www.amazon.com/Dent-Puller-Slide-Hammer-Repair/dp/B0176XYYIM/ref=sr_1_8?keywords=slide+hammer+dent+puller&qid=1557633698&s=gateway&sr=8-8
Glad you solved it. For future reference, a set of picks is one of those things that should be in everyone's toolbox.
An inexpensive Tekton set would be better than the HF ones:
https://www.amazon.com/TEKTON-6943-Precision-Pick-4-Piece/dp/B000NPPBQK
or like already mentioned, Channellock made in usa:
https://www.amazon.com/Channellock-HP-4A-Coated-Acetate-Handle/dp/B00RMR1X82/
or Craftsman:
https://www.amazon.com/Craftsman-Hook-Pick-Cushioned-Handles/dp/B001OIMXYI/
I like the handles on the Gearwrench:
https://www.amazon.com/GearWrench-84000D-Hook-Pick-Set/dp/B002EYI19M
made in Taiwan, tho.
In addition to flush cutters, I've found a few different types of picks help to clear out hard to reach support areas, and fastener holes. Just don't punture your finger!
https://www.amazon.com/TEKTON-6943-Precision-Pick-4-Piece/dp/B000NPPBQK
Use a pick set. I got a set at Northern Tool after tearing my car apart and getting to a point where I was so frustrated I almost just gave up and put it all back, but asked around in my local ST/RS Facebook group for ideas on how to remove the damn clip.
https://www.amazon.com/dp/B000NPPBQK/ref=cm_sw_r_cp_apa_i_MmJkDb8YT215N
I also couldn't remove the idiotic, corroded Torx bolt holding on the heat shield, so just wound up bending it back as far as I could.
Finally was able to pry off the clip whilst tearing up my hand a ton, but totally lost the clip. Make absolutely sure you don't do that.
They don't just sell the replacement from Ford as it's considered a part of the entire turbo assembly, and other parts you'll find when Googling aren't a fit. I'm currently running the TurboSmart WGA without the clip and it's been fine for about 4 months (since there's so much tension on it from the actuator arm), but sometimes I worry the arm will slip off, and the process to fix WON'T be fun.
Hope this helps.
Oooo I love tool shopping. So if I had to start over buying tools here's my list
Wrenches
1/2" sockets
3/8+1/4 sockets
Oil strap wrench
Pry bars with strike cap
1/2" impact
Pick set
Door upholstry remover
Stethoscope
Valve core tool
Electrical tool
Pliers: needle nose, long length needle nose, end nippers, diagonal cutters, tongue and groove, locking of all sizes and shapes
Lockable tool box, I like Husky Husky 2 electric boogaloo and HF cart don't forget to use the coupon!
if those are .110 connectors (hard to tell), there are flaps of metal holding the blades in the hood. i use a pick, like the straight one in this set: https://www.amazon.com/dp/B000NPPBQK
if you look at the second picture, it looks like you can see the flap down there on the left side of each connector blade. push on the wire from the back to slide the blade forward (hopefully unwedging the flap from being stuck against the hood), dig down with the pick, and try to push the flap back into the blade. then, while maintaining that pressure, pull back on the wire.
having three hands would be really useful for this, but it can be done. as it turns out, i spend all afternoon doing this trying to build a connection harness between the old bike and a new cluster i bought.
Yes, usually sold in sets with different angles/shapes at the tip.
http://www.amazon.com/TEKTON-6943-Precision-Pick-4-Piece/dp/B000NPPBQK/ref=sr_1_1?s=industrial&ie=UTF8&qid=1459019642&sr=1-1&keywords=pick