Reddit reviews Enerwave ZWN-RSM2-PLUS Z-Wave Plus Switch Module, Dual Relay, Smart Hidden Switch, NEUTRAL WIRE REQUIRED, Black
We found 14 Reddit comments about Enerwave ZWN-RSM2-PLUS Z-Wave Plus Switch Module, Dual Relay, Smart Hidden Switch, NEUTRAL WIRE REQUIRED, Black. Here are the top ones, ranked by their Reddit score.
"Next Gen" Z-wave PLUS Upgrades existing wall switch into a Z-Wave switch so you can still keep the original switch and wall plateWirelessly Switch your Devices (Lights, Fans) ON / OFF from Smart Phone Applications, Any Web Browser from Any PC or Mac, or Internet Connected TabletThe ON / OFF Control of the Connected Load can be Programmed into Z-Wave Scenes, with Dynamic Scheduling and Events from AnywhereZ-Wave hub required. Utilizes 5th Generation 500 Series hardware platform, 67% improvement in range, Faster & Easier Install and Set up, Additional RF channels, fully backwards compatible with existing z-wave productsNEUTRAL WIRE REQUIRED! Not compatible with security panels such as Honeywell Panel, NORTEK (2GIG) Security and Control Panel
The obvious solution is to replace the wife. ;)
That being said, however, you could install one of these guys then hook the switch to it: https://smile.amazon.com/Enerwave-ZWN-RSM2-Converting-Switches-REQUIRED/dp/B01G7OD3ME
It would still allow the physical switch to change the state of the bulb but it would always be in control so you could still turn the light back on through automated methods.
You would need a hub though for that option to work.
You could use something like this:
https://www.amazon.com/dp/B01G7OD3ME
I think Aeotec makes a dual switch one as well.
Otherwise you could just remove the current gang box and put in a larger one to accommodate 2 smart switches.
>Whatever you do don't get this guy or any crap from this company! https://smile.amazon.com/gp/product/B01G7OD3ME/
Wait, why not? I have one of those, and had nothing but good things to say about it. (I put enerwave and monoprice at about the same point, feature and quality wise.)
You need to use something like the Enerwave in-gang dual zwave relay. Aeon labs makes something equivalent to it as well. It will sit in the gang box behind your existing switch, and permit you to control each of the loads independently. I've got a few of these installed - they work very well with Wink.
You could also use the Wink Relay.
In theory, you could use one of the dual relays to connect both the fan and the light switch. The only downside is that you won't be able to control the fan speed.
https://www.amazon.com/Enerwave-ZWN-RSM2-Converting-Switches-REQUIRED/dp/B01G7OD3ME/ref=sr_1_1?ie=UTF8&qid=1480261041&sr=8-1&keywords=dual+relay+z-wave
https://www.amazon.com/Enerwave-ZWN-RSM2-Converting-Switches-REQUIRED/dp/B01G7OD3ME
Keeping in mind my only experience is with TP-Link switches, which won't work for you, here is what I think will work:
https://www.amazon.com/Enerwave-ZWN-RSM2-Converting-Switches-REQUIRED/dp/B01G7OD3ME/ref=sr_1_1?ie=UTF8&qid=1481508259&sr=8-1&keywords=enerwave+zwn-rsm2
With this you keep your existing switches and this module should (must) fit behind them in the box. If it won't fit, I think it can optionally be located in the ceiling fan housing.
This uses Z-wave remote control technology and thus requires a Z-wave hub such as the Samsung Smart Things hub shown in the Amazon listing linked above. Note the 3 links to guides/manuals also further down in that listing. One of those has the installation instructions including a wiring diagram.
With this system your manual switches still control the light/fan but the z-wave control also controls them and can be linked to Alexa control. Z-wave control does NOT depend on the manual switches being on.
https://www.amazon.com/Enerwave-ZWN-RSM2-Converting-Switches-REQUIRED/dp/B01G7OD3ME
Pretty sure you can use this. Much like the one you linked from Home Depot, it can be installed in the fan canopy. The wall switch will still work to turn the whole thing on and off, but when on, you can control the can and light separately- or create a virtual switch to turn them on/off simultaneously
If you have a hub that handles z-wave, maybe something like this would work? https://www.amazon.com/dp/B01G7OD3ME
But z-wave isn't gonna reach 200ft, so you'd need a repeater or something.
An alternative would be to just bypass the switch and install this behind the cowling of the fan. No fan speed/dimmer control tho.
I use this dual relay microswitch https://smile.amazon.com/Enerwave-ZWN-RSM1-Wireless-Control-Required/dp/B01G7OD3ME/ref=sr_1_1?ie=UTF8&qid=1492431936&sr=8-1&keywords=zwave%2Bmicro%2Bswitch&th=1
Its in the fan housing. And lets me turn on and off the fan and lights independently. It has some caveats, however, it requires the light switches that control the fan/light to be on permanently, if they are turned off, you lose remote functionality. Also, they cannot dim the lights or control fan speed.
Note that with this switch, you'll need to install a device type handler so that it will recognize the dual relays.
I didn't research it to much, but I have seen controllers that install behind the normal switch that support more than one input. So perhaps you can use some combination to control parts of you switch? Enerwave Z-Wave Plus Switch Module ZWN-RSM2 Converting 2 Current Switches Smart, NEUTRAL WIRE REQUIRED, Black https://www.amazon.com/dp/B01G7OD3ME/ref=cm_sw_r_cp_apa_qzMAybJP795M6
https://www.amazon.com/dp/B01G7OD3ME/ref=nav_timeline_asin?_encoding=UTF8&psc=1
Assuming you have neutral and space in the box this would allow you to control both lights individually.
There is a custom device handler for smartthings though and that might take some edumacation.
https://community.smartthings.com/t/release-enerwave-zwn-rsm2-v1-v2-rsm2-plus-smart-dual-relay-switch-module/44256
Not sure about other hubamathings