Reddit reviews Silverworm 12 AWG Real Silver Plated Flexible Copper Wire 12 AWG by ACER Racing
We found 2 Reddit comments about Silverworm 12 AWG Real Silver Plated Flexible Copper Wire 12 AWG by ACER Racing. Here are the top ones, ranked by their Reddit score.
SILVERWORM 12 Gauge Real Silver Plated Silicone High Performance Copper WireSuper Flexible 680 Strands of silver plated copper wire: silver has the lowest electrical resistance of any metal, followed by copper and then gold. We created silver + copper wire the most efficient metals.10 feet Total - 5 feet Black and 5 ft Red
These are what I use on the tevo and when I put the e3dv6 on the ender I'll use them there too....
I started them about 6 inches back up the wires from the hot end spaced them out so them aren't one big blob.... used different ones for different things so they can't be switched out and if for some reason a wire pulls loose it doesnt short anything... doing it I can swap out the hot end in minutes, do a PID tune and I'm off to the races.
Connectors and max current rating
Jst-sm for the fans and thermistor - 3amp
https://smile.amazon.com/gp/product/B07CTKD7P4/
Mini Tamiya type b for the heater - 10 amp
https://smile.amazon.com/gp/product/B06XSD9JJQ/
Jst-xhp are the white connector for stepper motors - 3 amp
https://smile.amazon.com/gp/product/B07CTH46S7/
Dupont for the black on the main board - 3 amp
https://smile.amazon.com/gp/product/B07CVYPDGS/
These for heated bed - up to 30 amps - solder only, not crimp
https://smile.amazon.com/gp/product/B07H54LZN2/
Crimpers - get the right ones for the pin type in the connectors you buy, you can't use just any old crimper or wing it with these tiny pins and get a good connection that doesn't come apart when things move for hours
https://smile.amazon.com/gp/product/B01N1RFZZ4/
https://smile.amazon.com/gp/product/B00YGLKBSK/
https://smile.amazon.com/gp/product/B00OMM4YUY/
Since I'm on the subject heated bed wires - large enough to carry the current and with the silicone cover and fine internal strands flexible enough to not break with movement
https://smile.amazon.com/gp/product/B01M9IXL5Q/r
When I was asking about this for the ender 3 /u/robbob2112b gave a very detailed breakdown on what they had done.
> These are what I use on the tevo and when I put the e3dv6 on the ender I'll use them there too....
>I started them about 6 inches back up the wires from the hot end spaced them out so them aren't one big blob.... used different ones for different things so they can't be switched out and if for some reason a wire pulls loose it doesnt short anything... doing it I can swap out the hot end in minutes, do a PID tune and I'm off to the races.
>Connectors and max current rating
>Jst-sm for the fans and thermistor - 3amp
>https://smile.amazon.com/gp/product/B07CTKD7P4/
>Mini Tamiya type b for the heater - 10 amp
>https://smile.amazon.com/gp/product/B06XSD9JJQ/
>Jst-xhp are the white connector for stepper motors - 3 amp
>https://smile.amazon.com/gp/product/B07CTH46S7/
>Dupont for the black on the main board - 3 amp
>https://smile.amazon.com/gp/product/B07CVYPDGS/
>These for heated bed - up to 30 amps - solder only, not crimp
>https://smile.amazon.com/gp/product/B07H54LZN2/
>Crimpers - get the right ones for the pin type in the connectors you buy, you can't use just any old crimper or wing it with these tiny pins and get a good connection that doesn't come apart when things move for hours
>https://smile.amazon.com/gp/product/B01N1RFZZ4/
>https://smile.amazon.com/gp/product/B00YGLKBSK/
>https://smile.amazon.com/gp/product/B00OMM4YUY/
>Since I'm on the subject heated bed wires - large enough to carry the current and with the silicone cover and fine internal strands flexible enough to not break with movement
>https://smile.amazon.com/gp/product/B01M9IXL5Q/r