Reddit reviews Zooz Z-Wave Plus Power Switch ZEN15 for 110V AC Units, Sump Pumps, Humidifiers, and More
We found 11 Reddit comments about Zooz Z-Wave Plus Power Switch ZEN15 for 110V AC Units, Sump Pumps, Humidifiers, and More. Here are the top ones, ranked by their Reddit score.
POWERFUL PLUG: The only Z-Wave Plug that lets you safely control and monitor heavy-duty 110V appliances from your Z-Wave smart home system. Connect your refrigerator, humidifier or dehumidifier, AC unit, fan, sump pump, or a gas clothes dryer to Z-Wave. NEW: 45 degree angled plug so you can fit 2 Smart Switches in a single receptacle!POWERFUL Z-WAVE: With built-in Z-Wave Plus signal repeater and range test tool, the Power Switch will boost your whole Z-Wave network while keeping it protected with AES signal encryption.POWERFUL CONTROL: Monitor energy use of connected appliances in live mode or over time with W, kWh, A, and V reports (your Z-Wave hub needs to support this feature). Quick status reports to the controller and on/off state recovery after power failure.POWERFUL HARDWARE: Made from high-quality components that will last, even when it's very cold or very hot (14° - 104°F, indoor use only). ETL certified: complies with North American electrical safety standards. Extra-thick flexible cord is perfect for installations with no immediate access to a receptacle.COMPATIBILITY: Use the Power Switch with any certified Z-Wave gateway for simple on/off control (Wink, Z-Wave alarm panels). Advanced settings and energy monitoring available for open systems only, including Vera, SmartThings (custom device handler required, contact seller first), HomeSeer, and Fibaro Home Center Lite.
Sure, here's a few:
https://smile.amazon.com/Z-Wave-Power-Switch-ZEN15-Humidifiers/dp/B07578W7KY/
https://smile.amazon.com/HAOZEE-Automation-Extender-Monitoring-SmartThings/dp/B0781XZYWR/
https://smile.amazon.com/Aeotec-Aeon-Labs-ZW096-ZW096/dp/B00VQISOCG/
What country are you in? If you have a scriptable hub, I think you can do this with relative ease.
You'll need switchable outlets with power reporting functionality and enough current handling to power the heater or microwave individually. https://smile.amazon.com/Z-Wave-Power-Switch-ZEN15-Humidifiers/dp/B07578W7KY/ something like this may work if you're in the USA and have a z-wave hub.
You would have to create a script/automation that checks the reported power consumption from the microwave, and if microwave wattage > say 100 watts, turn off the heater. Add a second automation that turns the heater back on when microwave wattage drops below 50 watts for 1 minute.
Note: The sensing and controlling logic for this will take a few seconds to trigger. I'm saying this will work because you've said the breaker will pop "eventually". If the breaker pops in under 30 seconds, I'd say you're out of luck without rewiring the circuit or building an uninsured DIY device that would cause more problems than solutions.
Since you say "outlet", perhaps a z-wave on/off module with load sensing would work for this, but I'd be concerned that it could turn off power to the pump (maybe get one with a relay, and jumper the output to always on?)
You could use a current transformer to detect the power drawn by the pump in a non-intrusive manner, but most such products are kind of expensive unless you build your own. These are especially useful for hardwired devices.
Personally, I bit the bullet and bought a Multi-CT monitoring solution for $$$ (TED Pro Home)
Is the pump plugged into an outlet? If so, why not get a zwave power switch that reports how many amps are being drawn. https://www.amazon.com/Z-Wave-Power-Switch-ZEN15-Humidifiers/dp/B07578W7KY/ref=sr_1_2?keywords=zwave+cord&qid=1557887622&s=gateway&sr=8-2
You'd also need a zwave hub if you don't have one. Personally think it's good to keep your smart home tech separate from your security tech.
The Zooz ZEN15 has been the go too everywhere I've seen. I have 3 of them (Dishwasher, Washer, Dryer)
Stating the obvious here but these won't work for electric dryers.
https://www.amazon.com/Z-Wave-Power-Switch-ZEN15-Humidifiers/dp/B07578W7KY/
What about this.
Zooz Z-Wave Plus Power Switch ZEN15 for 110V AC Units, Sump Pumps, Humidifiers, and More https://www.amazon.com/dp/B07578W7KY/ref=cm_sw_r_cp_apa_i_RWTwDb36VCV6A
It can monitor the power level, and send an alert when it spikes above a threshold.
Then your hub can trigger automations based on that alert.
I use these Zooz z-wave power metered switches and WebCore to send notifications for my washer and dryer being done. Works perfectly.
Don't over-complicate things.
You could connect your pump to a power switch like this one which can be set up to send alerts based on energy use. Then for water level maybe just place a moisture sensor inside the sump pit at a specific height? Might be difficult to attach to the side of the pit, so maybe hang it from the cover or attach it to the pump's discharge pipe with a clamp or zip ties.
Zooz Z-Wave Plus Power Switch... https://www.amazon.com/dp/B07578W7KY?ref=ppx_pop_mob_ap_share
Works very well. Z-wave. Using it with home assistant. They also make a two outlet version Zen 25
For the price, it seems like I'm better off just getting something like this Zooz 110V plug and modifying the ends so that it's hard wired instead of plugged in. https://www.amazon.com/Z-Wave-Power-Switch-ZEN15-Humidifiers/dp/B07578W7KY/ref=sr_1_5?crid=2HXRD0N5K12PC&keywords=zooz+zwave+switch&qid=1565629021&s=gateway&sprefix=zooz+%2Caps%2C147&sr=8-5
I use the Zooz power switch for energy monitoring and home assistant automations for the notification.
https://www.amazon.com/dp/B07578W7KY/ref=cm_sw_r_cp_apa_i_FLszDbWM4R46T
You do have to do a bit of experimentation to get your power ranges correct but it works really well.