Reddit reviews 6-in-1 60W Soldering Iron Gun with Carry Case and Cleaning Sponge Stand, SOAIY Adjustable Temperature Welding Soldering Iron, Including 5pcs Different Soldering Tips, Desoldering Pump, Soldering Wire
We found 8 Reddit comments about 6-in-1 60W Soldering Iron Gun with Carry Case and Cleaning Sponge Stand, SOAIY Adjustable Temperature Welding Soldering Iron, Including 5pcs Different Soldering Tips, Desoldering Pump, Soldering Wire. Here are the top ones, ranked by their Reddit score.
6-In-1 full kit - kit comes with tool carry case, soldering iron, 5 soldering tips, soldering sucker (disordering pump), solder wires, stand with Cleaning sponge. Full set tool make it perfect for daily use such US electric repair, home DIY and wood burning projection.Heat up quickly - 60 watts, with upgraded ceramic heater chip and heat up quickly (2 minutes or so). adjustable temperature with thermostat range 200450℃.Better heat dissipation hole and anti-slip handle – 3 heat dissipation holes on the tips and anti-skid rubber handle is good for long time project.Safe and environmental protection soldering wire included, There are ingredient listed on the tinned tube Package, lead free solder wire is , non-toxic, non-polluting, safe to use.Easy for storage - tool carry case is an additional feature, and rather convenient to store small tools and easy to carry.
This is the one I use (and really really like).
https://www.amazon.com/Weller-WES51-Analog-Soldering-Station/dp/B000BRC2XU
To be honest, it would be overkill for just hobby use (I am heavy into drones and other electronics that require a lot of soldering on a very wide range of wires and parts).
This is a great little kit that will get you started;
https://www.amazon.com/dp/B01C9P7HDQ?psc=1
tl;dr I would not spend much more than about 20-30 bucks for your first one, if you use it a ton and get into electronics, you can always upgrade and keep the first one as a travel iron.
I'm using Amazon links as requested, but if you have a local big box tool stop you can get the store brand of most all these items for the same price or less. I know from personal experience, that from the tools I've listed all but two of the items are cheaper in store than on Amazon.
Everyone needs a knife! (~$7 home depot)
Razor blade
Where are you going to keep everything? (~$10 home depot)
Utility Sack
You'll need a good all around screw driver. (~$8 home depot)
6-in-1 Reversible Screwdriver
Need some basic general maintenance pliers? (~$20 home depot)
Pliers Set
Ratcheting screwdriver for those repetitive screw jobs. (~$20 sears)
Ratcheting Screwdriver
Where the hell did I put that T6?
Magnetic Precision Screwdriver Set
Where did that damn screw go?
Flashlight
Extra stuff!
I recommend the ball end ones specifically if you don't have a good angle on what your trying to get at (cough towel bar cough cough).
Long Arm Ball End Hex Key Wrench Set
For those damn pesky wires and that damn lack of a third hand.
Helping hands
When duck tape and gum wont cut it.
Beginners soldering iron kit
I have used all of these specific items extensively besides the ball end hex keys, and that specific helping hands.
I have one of these. For light duty work, it's served me well.
https://www.amazon.com/dp/B01C9P7HDQ/ref=cm_sw_r_cp_apa_i_gTZdBb0TKEC2V
This super cheap one from amazon. To make things worse I used the included solder.
I managed, but it definitely got a little hairy near the end as the tip got wider and pieces started coming off. I have a Hakko on my wishlist, but won't be able to get it until next week. Impatience is bad.
I used this kit with the heat turned all the way down and it melts PLA nicely.
I got this guy a while back. Helped me make a few custom cables, a GH60, and a planck so far. Looking to build a bunch more with it too. It's a great little workhorse
The only video I could find of the MOSFET board installation was very long and somewhat unclear to a newbie. It looks like he mounts it under the printer rather than the control box and overall just seemed really difficult.
I just went ahead and pushed the button on my order from Amazon that includes the XT60 Connectors w/ Heat Shrink and the 6-1 Soldering Kit I would have preferred the MOSFET but in hopes of not getting over my head, it was a total of about 30$ and seems doable.
just looked that iron up, says it a 60w, could be BS but more likely didn't wait for the iron to reach temp.
https://www.amazon.com/Soldering-Adjustable-Temperature-Including-Desoldering/dp/B01C9P7HDQ/ref=sr_1_2?s=hi&ie=UTF8&qid=1518835087&sr=1-2&keywords=SOAIY+IRON