Reddit reviews BOSTITCH Pancake Air Compressor, Oil-Free, 6 Gallon, 150 PSI (BTFP02012)
We found 5 Reddit comments about BOSTITCH Pancake Air Compressor, Oil-Free, 6 Gallon, 150 PSI (BTFP02012). Here are the top ones, ranked by their Reddit score.
Note:Item does not includes hose or gun kit150 max PSI 6.0 gallon tank (22.7 L) and 2.6 SCFM* delivered @ 90 PSI pumpHigh efficiency motor for easy start up in cold weather ; BOSTITCH high efficiency motor for easy start up in cold weather or extension cord application [14 ga or larger, 50 ft. (15.2 m) or less]78.5 dBA** operational noise level for a quiet work environmentHigh flow regulator and couplers to maximize air tool performanceLong life oil free, maintenance free pump for convenient use
For a serious job like this you need serious tools
https://www.amazon.com/Bostitch-BTFP02012-Gallon-Oil-Free-Compressor/dp/B00UHNM1R0/
No. You need a compressor with a tank. Like this:
https://www.amazon.com/Bostitch-BTFP02012-Gallon-Oil-Free-Compressor/dp/B00UHNM1R0/ref=mp_s_a_1_5?keywords=compressor&qid=1572901324&sr=8-5
Yup, you’ve got the burn rate and replenishment rate correct. It’s ok if your burn rate is higher than your replenishment rate, that just means you’ll need to take breaks.
Harbor Freight says you need 6 CFM at 40 psi. I’ll assume that’s for continuous spraying with the normal pauses for start & stop of each pass.
6 CFM is ~ 48 gallons, so you need 48 gallons of air at 40 psi to operate this paint gun. Pressure is inversely proportional to volume: If you double the pressure in your tank, you can squeeze twice as much air in, so you fit twice as many gallons. So a 24 gallon tank at 80 psi would let you spray continuously for a minute before being totally empty.
A little compressor like this should be OK for you: https://www.amazon.com/Bostitch-BTFP02012-Gallon-Oil-Free-Compressor/dp/B00UHNM1R0
It’s rated to 150 psi, so you can run it at 120 psi or so, and it’ll hold the equivalent of 18 gallons of air at 40 psi, which is about 22 seconds of continuous operation. The pump delivers 2.6 CFM at 90 psi, which is approx 5.2 CFM at 40 psi, which should nearly allow continuous operation. You’ll need to pause now and then to let the tank refill, but it should provide plenty of air to paint one panel at a time, and it’s not too expensive ($100).
For a little more money ($288), something like this (20 gallon, 4 CFM @ 90 psi) would let you paint continuously: https://www.amazon.com/Compressor-Horizontal-Campbell-Hausfeld-DC200000/dp/B01M7Q5RUO
If you're in a dusty environment raise the tower off the ground to reduce dust cleaning intervals. I typically blow out the computer tower with a compressor tank of air. https://www.amazon.com/Bostitch-BTFP02012-Gallon-Oil-Free-Compressor/dp/B00UHNM1R0/
Suggestions on an air compressor? I was going to get the Master TC-40T at ~$120ish, but it looks like that might have been replaced by the TC-96T (at ~$200). Links for the 40T direct to the 96T on Amazon instead. Not sure what's up with that. I've already bough a Patriot 105 and Krome, a quick disconnect fitting, and a Badger airbrush hose.
We do already have one of these at home we use with a nail gun:
https://www.amazon.com/Bostitch-BTFP02012-Gallon-Oil-Free-Compressor/dp/B00UHNM1R0
I know i can get a regulator and water trap to use with that, but it's very loud. Figured something quieter would be good. Although if it is big enough that it only needs to fill once during a paint session that may work alright.