Reddit Reddit reviews Motion Pro 08-0048 Chain Alignment Tool

We found 7 Reddit comments about Motion Pro 08-0048 Chain Alignment Tool. Here are the top ones, ranked by their Reddit score.

Automotive
Motorcycle & Powersports
Powersports Accessories
Motion Pro 08-0048 Chain Alignment Tool
Quick and accurate alignmentTool body clamps squarely to rear sprocket so the alignment rod will indicate sprocket alignment to chainMotion Pro Chain Alignment Tool can be used on motorcycles and ATVsMade in the China
Check price on Amazon

7 Reddit comments about Motion Pro 08-0048 Chain Alignment Tool:

u/curiouspoops · 3 pointsr/hondagrom

I believe the proper spec is 35mm for the newer groms.

You really don't want to deviate from that too much. Anywhere from 30-40mm is fine. 50mm or more and it can potentially be dangerous to ride. In fact, the owner's manual says do not even ride it if it's at 50mm or more.

These tools come in handy and I use them every time I adjust my chain.

  1. MOTION PRO Slack Setter Pro Chain Tension Tool

  2. Motion Pro 08-0048 Chain Alignment Tool


    And yes, each time you loosen the axle nut, you will most likely have to readjust your chain tension. Do not try to make adjustment without loosening the axle nut first. This is not a hard task to accomplish once you've done it enough times. The important part is obtaining the proper slack in the chain and also making sure the rear tire stays straight. That is what the chain alignment tool is for, because you can't always rely on the hash marks on the swingarm.

    This video has been pretty helpful for me, because he shows the correct process of chain slack adjustment, starting with the tire pushed all the way forward and slowly getting it into spec. It's on a Ninja 300 but the same concept applies.
u/KrimTheRed · 2 pointsr/motorcycles

I've done my rubber on my KLR. I have tubes but the process is (I'm guessing) pretty much the same:

  1. Lift bike off ground. I have a stand to pick up the entire thing but you can do just one tire at a time. We'll do the front.
  2. Remove the front axle. Loosen the axle nut and then the pinch bolts. Don't remove the axle nut. Lightly tap the axle nut to slide the axle out the other side. Keep backing the nut off and tapping until you can't back the nut out anymore. Remove the nut and pull the axle, supporting the tire. Inspect axle for wear and place on some shop rags. Remove speedometer cable when removing front tire. DO NOT SQUEEZE THE BRAKES WITH THE TIRE REMOVED. This will cause you problems trying to open your brake calipers back up to get the rotor in again.
  3. Change your tire. Watch this video for instructions: https://www.youtube.com/watch?v=dAKIuSjPXxA
  4. Put your front wheel back on, lube your axle.
  5. Take the back wheel off in a similar fashion. Change the rubber in the same way.
  6. Adjust your chain, instructions here: https://www.youtube.com/watch?v=Tqu7WGELU5s

    There are some tools to help you:

u/_tanith · 2 pointsr/motorcycles

Buy one of these to check your rear wheel alignment: https://www.amazon.com/Motion-Pro-08-0048-Chain-Alignment/dp/B000GTVOJQ/ref=sr_1_1?ie=UTF8&qid=1509748960&sr=8-1&keywords=motion+pro+chain+alignment+tool

u/DevoxNZ · 1 pointr/motorcycles

Yea, you're going to want to make sure the rear wheel is aligned properly when adjusting your chain. One of these helps me.


https://www.amazon.com/d/Tire-Repair-Tools/Motion-Pro-08-0048-Chain-Alignment/B000GTVOJQ

u/Chilton_Squid · 1 pointr/MotoUK

The notches aren't great to be honest, but once you know it's straight you can just adjust by the same number of turns each side and probably be fine. Get yourself one of these though:

https://www.amazon.co.uk/Motion-Pro-08-0048-Chain-Alignment/dp/B000GTVOJQ

u/BigRedS · 1 pointr/MotoUK

> Any tips as to how to accurately measure the distance between pivot and tip of the swingarm

This isn't really the important measurement - you want the chain to be straight, and there's a few alignment tools for that:

https://www.amazon.co.uk/d/Car-Tools-Equipment/Laser-5051-Motorcycle-Chain-Alignment-Tool/B004499M20/

https://www.amazon.co.uk/Sealey-MS005-Motorcycle-Chain-Alignment/dp/B008H144EC/

https://www.amazon.co.uk/Motion-Pro-08-0048-Chain-Alignment/dp/B000GTVOJQ


How did you realise the markings were off? I don't really understand what your response is that would involve a loose nut.

u/degoba · 1 pointr/motorcycles

The marks on the swingarm are more for measuring chain wear and health than alignment. Id suggest picking up motion pros chain alignment tool for 15 bucks. https://www.amazon.com/Motion-Pro-08-0048-Chain-Alignment/dp/B000GTVOJQ