Reddit reviews Motorola Signal Booster BDA-S1 1-Port Cable Modem TV HDTV Amplifier

We found 3 Reddit comments about Motorola Signal Booster BDA-S1 1-Port Cable Modem TV HDTV Amplifier. Here are the top ones, ranked by their Reddit score.

The BDA-S1 is a bi-directional cable TV amplifier designed for use in homes. Boosts signal by 32x.This is the commercial version of the Motorola Signal Booster 484095-001-00. It includes a power supply - no coaxial cables included.Amplifies your cable TV signal to dramatically reduce snow, graininess, digital pixilation and other picture problems.Meets all applicable IEEE surge standards for all output ports, which enhances system reliability.Weather seal and protective coating allow use of the amplifier for indoor or outdoor applications.

Check price on Amazon

3 Reddit comments about Motorola Signal Booster BDA-S1 1-Port Cable Modem TV HDTV Amplifier:

u/team140 · 3 pointsr/GNV

I get 11 channels right next to Gainesville High School.:

5.1 WUFT-HD (PBS)
5.2 WUFT-CREATE (PBS)
5.3 WUFT-DT (PBS)
9.1 WNBW-DT (NBC)
9.2 WNBW-DT2 (MeTV)
20.1 WCJB-DT (ABC)
20.2 WCJB-DT2 (CW)
28.1 WGFL-DT (CBS)
28.2 WGFL-DT2 (My11)
51.1 WOGX-DT (Fox)
51.2 WOGX-DT2 (Movies!)

I used to work at Gainesville Television Network. In order to pull in the stations above, you'll need an attic to put an antenna in - or you can mount one on the roof or outside pole.

Antenna 1: Amazon Basics clone of the Leaf antenna

Antenna 2: Clearstream 5

Combiner: Channel Plus Combiner/Splitter

Signal Booster: Motorola Signal Booster

Take those items and some lengths of RF cable (CATV style cable) and connect as such:

Cable from each antenna into the two ports labeled "IN" on the combiner.

One cable from the "OUT" labeled port of the combiner to the "RF Input" connector on the signal booster.

One cable from the signal booster "RF Output 1" to your TV.

One cable from the signal booster "Power 12vdc" connector to the included power adapter, which is then plugged into the wall for power.

This will pull in the above 11 stations nearly anywhere in Gainesville. Of course, your results may vary depending on your location and such.

u/Justsomeguy1983 · 1 pointr/cordcutters

So aside from the fact that there is no replacement for antenna aperture size, if you do go the amplifier route. This one is hard to beat. amplifier

u/TheReal-JoJo103 · 1 pointr/AskElectronics

I would just run a single coax line out to the shop. If the range is too far look at a booster like this.

For internet I would use that same coax line. What your looking for is a MoCA adapter. I can't seem to find distance specs on this one but I believe you can get them with up to 1000ft of range. That will utilize unused bandwidth on the coax leftover from your cable to transmit ethernet. Point to point wifi is also an option, ubiquity has quite a few point to point options that are reasonable.

Edit: Looks like cisco calls it ethernet over coax (EoC) just make sure it can support the cable signal too.

Ethernet over powerline is also an option depending on your electrical setup. It doesn't have the greatest distance but it'll work if you can plug in near the breaker box.

Either way putting coax over fiber is probably far more expensive than just running a coax in parallel.