Best set-screw shaft collars according to redditors

We found 9 Reddit comments discussing the best set-screw shaft collars. We ranked the 7 resulting products by number of redditors who mentioned them. Here are the top 20.

1. Lovejoy Shaft Collar, Setscrew Style, Zinc-Plated Steel

1 mention
Lovejoy Shaft Collar, Setscrew Style, Zinc-Plated Steel
Setscrew shaft collar for applications supporting low axial loads and simple positioningEffective on shafts made of softer material than the setscrew materialSteel for weldability and rust resistance with zinc plating for better resistance to corrosion than black oxide steelIncludes a socket cup-poi...
Read Reddit commentsView price

2. Climax Metal Setscrew Shaft Collar, Black Oxide Steel

1 mention
Climax Metal Setscrew Shaft Collar, Black Oxide Steel
Setscrew shaft collar for applications supporting low axial loads and simple positioningEffective on shafts made of softer material than the setscrew materialSteel for weldability and rust resistance with a black oxide finish for a decorative appearance and for resistance to stick-slip, white corros...
Read Reddit commentsView price

3. Ruland MSC-6-SS Set Screw Shaft Collar, Stainless Steel, Metric, 6mm Bore, 12mm OD, 8mm Width (Pack of 4)

1 mention
Ruland MSC-6-SS Set Screw Shaft Collar, Stainless Steel, Metric, 6mm Bore, 12mm OD, 8mm Width (Pack of 4)
Setscrew shaft collar for applications supporting low axial loads and simple positioningEffective on shafts made of softer material than the setscrew materialStainless steel 303 for greater corrosion resistance than steel or aluminumIncludes a forged setscrew for securing the collar onto the shaftOp...
Read Reddit commentsView price

4. Climax Part C-075-DT, Mild Steel, Set Screw Collar, 3/4 inch bore, 1 1/4 inch OD, 9/16 inch Width, 5/16-18 x 1/4" Set Screw

1 mention
Climax Part C-075-DT, Mild Steel, Set Screw Collar, 3/4 inch bore, 1 1/4 inch OD, 9/16 inch Width, 5/16-18 x 1/4" Set Screw
Effective on hard and soft shaftsCost effective collar designEasily installed where major disassembly would otherwise be requiredTolerance: +.0005/+.0030No plating for corrosion resistance
Read Reddit commentsView price

5. Climax Metal C-200 Steel Set Screw Collar, Zinc Plated Steel, 2" Bore Size, 3" OD, With 1/2-13 x 1/2 Set Screw

1 mention
Climax Metal C-200 Steel Set Screw Collar, Zinc Plated Steel, 2" Bore Size, 3" OD, With 1/2-13 x 1/2 Set Screw
Effective on hard and soft shaftsCost effective collar designEasily installed where major disassembly would otherwise be requiredTolerance: +.0010/+.0040Zinc plating provides moderate corrosion resistance
Read Reddit commentsView price

6. Climax Metal C-068-S Shaft Collar, One Piece, Set Screw Style, Stainless Steel, 11/16" Bore, 1-1/4" OD, 9/16" Width, With 5/16-18 x 1/4 Set Screw

1 mention
Climax Metal C-068-S Shaft Collar, One Piece, Set Screw Style, Stainless Steel, 11/16" Bore, 1-1/4" OD, 9/16" Width, With 5/16-18 x 1/4 Set Screw
Setscrew shaft collar for applications supporting low axial loads and simple positioningEffective on shafts made of softer material than the setscrew materialStainless steel 303 for greater corrosion resistance than steel or aluminumIncludes a socket setscrew for securing the collar onto the shaftOp...
Read Reddit commentsView price

7. Climax Metal C-012 Shaft Collar, Zinc Plated Steel, Set Screw Style, One Piece, 1/8" Bore, 3/8" OD, 1/4" Wide, With 6-32 Set Screw, (10-Pack)

1 mention
Climax Metal C-012 Shaft Collar, Zinc Plated Steel, Set Screw Style, One Piece, 1/8" Bore, 3/8" OD, 1/4" Wide, With 6-32 Set Screw, (10-Pack)
Effective on hard and soft shaftsCost effective collar designEasily installed where major disassembly would otherwise be requiredTolerance: +.0005/+.0025Zinc plating provides moderate corrosion resistance
Read Reddit commentsView price
Next page

Top Reddit comments about Set-Screw Shaft Collars:

u/jackrats · 3 pointsr/whatisthisthing

Hard to tell from the blurry pic (seems like it's bad pic day today), but looks like a shaft collar.

Like this:

https://www.amazon.com/Ruland-MSC-6-SS-Collar-Stainless-Metric/dp/B0063KWH7U

u/ThePrincessDebride · 2 pointsr/ar15

Honest question. Why pay for that rather than paying for a generic 1.25" (or whatever diameter your tube is) shaft collar like this for a fraction of the cost?

u/jihiggs · 2 pointsr/arduino

set screw and collar
http://www.amazon.com/Climax-C-075-DT-Steel-Screw-Collar/dp/B005L6A8EG/ref=sr_1_7?s=industrial&ie=UTF8&qid=1422653418&sr=1-7

or you could flatten one side of the shaft and press something on.

u/wildecard · 2 pointsr/AskEngineers

Could be, maybe something like this and this together? Obviously not the correct sizes.

u/marsairforce · 2 pointsr/diytubes

Oh right!! 3D printing. I had not thought of that.

I saw a youtube channel once This guy had a nice vintage radio with a chicken head knob. He made a silicone cast and then used black epoxy to make his own knob. The tools and amount of work and detail he had to do to make it look good. He had a slotted shaft so made a small spring clip inside the round hole he drilled though.

But. for 3d printing. What if you 3d printed a knob to fit on top of metal collar with a set screw already in it. Something like this https://www.amazon.com/Lovejoy-LSC-10-Shaft-Collar-Plated/dp/B007JOHR9W/ref=lp_16411961_1_2?s=industrial&ie=UTF8&qid=1570770594&sr=1-2

you would need some kind of epoxy or maybe just a good friction fit to make the 3D printed part stick over this collar. And drill a hole to get to the set screw maybe. Or if you can. attach the collar and friction fit the 3D printed part over it?

u/Ganson · 1 pointr/headphonemods

Link to the appropriate sized shaft collars for anyone interested I used two each side, but I’ve seen people just use one at the top as well. Personal preference.

Climax Metal C-012 Shaft Collar, Zinc Plated Steel, Set Screw Style, One Piece, 1/8" Bore, 3/8" OD, 1/4" Wide, With 6-32 Set Screw, (10-Pack) https://www.amazon.com/dp/B000ILA7EK/ref=cm_sw_r_cp_api_4KoSBb31HFB3F

u/shul0k · 1 pointr/Strongman

Why do you need a second dumbbell?

I got a couple of these set screw collars that are awesome for keeping the weights in place. They use a 1/4 inch hex key which is mildly inconvenient.