Best wheel bearing tools according to redditors

We found 7 Reddit comments discussing the best wheel bearing tools. We ranked the 3 resulting products by number of redditors who mentioned them. Here are the top 20.

1. ATE 760130 ABS Test Card for Magnetic Sensor Wheels

3 mentions
ATE 760130 ABS Test Card for Magnetic Sensor Wheels
Protects against installation errors in the ABSFor magnetic sensor wheels, which are integrated in the rubber sealing ring of the wheel bearingMagnetic fields of the sensor wheel are shown visually in the display window of the ATE test card, making it possible to check themFast, simple and inexpensi...
Read Reddit commentsView price

2. OrionMotorTech 23-Piece FWD Front Wheel Drive Bearing Adapters Puller Press Replacement Installer Removal Tool Kit

2 mentions
OrionMotorTech 23-Piece FWD Front Wheel Drive Bearing Adapters Puller Press Replacement Installer Removal Tool Kit
ALL-IN-ONE TOOL KIT: Everything you need for fast & effective front-wheel drive bearing removal and installation. Easily replaces wheel bearings while keeping the steering knuckle and strut assembled on the vehicle.INCREASE EFFICIENCY: Designed to work with the steering knuckle and strut assembly st...
Read Reddit commentsView price

3. OTC 9850 6-Point Wheel Bearing Locknut Socket with Tool Board

1 mention
OTC 9850 6-Point Wheel Bearing Locknut Socket with Tool Board
Wheel bearing locknuts are easy to remove or install with these specially designed socketsMade of high-strength steel and resist rounding out21 wheel bearing locknut sockets with tool boardSockets are designed for use with 3/4 inch square-drive manual tools onlyImpact tool use voids sockets warranty
Read Reddit commentsView price
Next page

Top Reddit comments about Wheel Bearing Tools:

u/Clayjay15 · 11 pointsr/whatisthisthing

Definitely not an electrical hole punch set. Automotive wheel bearing removal and install set. https://www.amazon.com/OrionMotorTech-23-Piece-Adapters-Replacement-Installer/dp/B01FLVOAZI/ref=asc_df_B01FLVOAZI/?

u/xrfauxtard · 3 pointsr/Skookum

Amazon link
This has been around for awhile. Mercedes have the same setup in inner hub seals that have to be pressed on. You find out which ones pretty quick when you tap them in with a hammer instead of pressing them

u/rahtin · 2 pointsr/pics

Rarely used any wrenches bigger than 1 5/16 in our shop. Sockets on the other hand...

https://www.amazon.com/OTC-9850-6-Point-Bearing-Locknut/dp/B000OCIWVI

u/GotMyOrangeCrush · 2 pointsr/MechanicAdvice

Magnetic sensor tester?

https://www.amazon.com/ATE-760130-Magnetic-Sensor-Wheels/dp/B003VXPHW4

u/Raincor · 1 pointr/Damnthatsinteresting

As a mechanic, we use something similar to test which side of wheel bearings has the speed sensor pickup.

u/youknowarddarvis · 1 pointr/Honda

That's correct- to replace the studs, you must replace pull the hub out of the bearing.

UNLESS, there is a spot where you can cut and bend the brake shield out of the way so you could bash the old lugs out and new ones in. Ericthecarguy has a video where he does this exact thing--he replaces lugs without pulling the hub.

I use this wheel bearing press. It makes easy work of almost any job without removing the whole knuckle.

OrionMotorTech 23-Piece FWD Front Wheel Drive Bearing Adapters Puller Press Replacement Installer Removal Tool Kit https://www.amazon.com/dp/B01FLVOAZI/ref=cm_sw_r_cp_apa_wf3-BbMHRGCRQ