Reddit reviews Astro Pneumatic Tool 1442 13" Hand Rivet Nut Setter Kit - Metric & SAE W/ 60pc Rivnuts
We found 8 Reddit comments about Astro Pneumatic Tool 1442 13" Hand Rivet Nut Setter Kit - Metric & SAE W/ 60pc Rivnuts. Here are the top ones, ranked by their Reddit score.
New "Toolless Quick-Change Head" design allows for easy changing of mandrels and nose pieces by handDisassembly of tool never required, unique spring loaded inner hex sleeve automatically locks the rotation of hand installed mandrelShorter handle with double compound hinges maximizing leverage. Great for off-road / Jeep modifications6 interchangeable mandrel/nosepiece sets and 10pc rivet nuts in Metric M5, M6, & M8 and in SAE 10-24, 1/4-20, & 5/16-18Includes 10 pieces of each of the following rivet nuts: M5, M6, M8,10-24, 1/4-20 and 5/16-18
pick this up and make your life easier.
https://www.amazon.com/gp/product/B003TODXQW
There’s only so much a powered all-in-one sub combo can do. It’s all a compromise.
They’re not going to be able to compete with a more robust external amp, a full-size driver, and an enclosure with adequate volume.
I’m just saying to temper your expectations.
but regardless of what you have, the box should definitely be secured. ESPECIALLY SO if the box shares the same space as passengers. It’s a major hazard in the event of a crash.
Apart from getting thrown around, any energy spent vibrating/shaking the box is lost output.
Whatever the gear, I’m all for installing it in the proper way to let it reach it’s potential.
......
There’s multiple ways to do it:
L-Brackets are one, like 4 of em, decent sized, screwed/bolted right to the side of the box and then secured to the floor.
To do that, you could drill through the floor pan and use a nut and bolt to secure the brackets
Kind of a pain to remove the box that way....and just in general.
Better would be to slip a board under the carpet/liner; bolt that through the floor, and use insert nuts to add threads to the board that you can screw the L-brackets to.
and even better than that, skip the nuts and bolts and use threaded rivets to add threads directly to the metal floor pan
That does involves buying another tool, though. There’s a cheaper version at Harbor Freight, but the rivets are soft and somewhat prone to spinning in the hole.
The easiest method overall is to just use a ratchet strap over the top, secured to cargo hooks. Which you can add if need be with the techniques above.
....
If you drill:
Always check, double check where you’re drilling; and anytime you drill through painted metal, good to use touch-up paint around the hole or at least apply some grease to prevent rust.
It really helps to set a centering divot with a punch or hammer and a nail. It’ll keep the bit from wandering
Second this. It's a revnut or pemnut. Did use them extensively, pretty sure you can't retap it, it would just spin.
The tool to install them is here https://www.amazon.com/gp/aw/d/B003TODXQW
I'd just rip it out and put in a new one.
Rivnuts, Astro Pneumatic Tool 1442 Nut/Thread Setting Hand Riveter Kit, 13-Inch https://www.amazon.com/dp/B003TODXQW/ref=cm_sw_r_cp_apa_5ZXYzb1S8Z4Y7
Astro Pneumatic Tool 1442 Nut/Thread Setting Hand Riveter Kit, 13-Inch https://www.amazon.com/dp/B003TODXQW/ref=cm_sw_r_cp_apa_TU1Lyb9HBZE1D
This is nice.
By tool do you mean the Rivnut setter? I got that from Amazon because I saw that it was a recommended tool to use from reading reviews about it. It ended up being pretty easy to do though and not that hard. This is the tool I bought https://www.amazon.com/gp/product/B003TODXQW/ref=ppx_yo_dt_b_asin_title_o00_s00?ie=UTF8&psc=1
Forsee this in your future....
Astro Pneumatic Tool 1442 13" Hand Rivet Nut Setter Kit - Metric & SAE W/ 60pc Rivnuts https://www.amazon.com/dp/B003TODXQW/ref=cm_sw_r_cp_apa_i_3EpADb59QG8P4