Reddit Reddit reviews Meguiar's X3070 Soft Foam 4" Applicator Pads - (Pack of 2)

We found 12 Reddit comments about Meguiar's X3070 Soft Foam 4" Applicator Pads - (Pack of 2). Here are the top ones, ranked by their Reddit score.

Automotive
Automotive Tools & Equipment
Body Repair Tools
Body Repair Buffing & Polishing Pads
Meguiar's X3070 Soft Foam 4
Evenly and safely applies wax, polish, or tire dressingUltra-soft foam has tight cellsPad is washable and reusable
Check price on Amazon

12 Reddit comments about Meguiar's X3070 Soft Foam 4" Applicator Pads - (Pack of 2):

u/chadcf · 10 pointsr/pics

You can buy everything online, though it's easier to go to a harbor freight with a coupon if you have one. There are plenty of polishers you can buy online of course, but none are as cheap (at least with decent quality) as the harbor freight model. You can of course buy a much better polisher at your local lowes / home depot however unless you have a lot more use for it it's probably not worth it over the harbor freight one (a good polisher will cost you $200+). Everything else you can find at any auto parts store, or maybe even walmart.

Here's some links

  1. Start with touch ups if needed. Apply touchup paint to chips with a toothpick, in small amounts. Let it dry and do another one, build it up until it's above the level of the surrounding paint (may take many coats). Let it dry at least several days and make sure it hasn't sunk in. After it's dried for several days, use some water and the sanding block to gently sand them down flush with the rest of the paint. It will look bad, don't worry. Give the paint a few weeks to cure before moving on.
  2. Wash the whole car with dawn dish soap and let it dry. Mix up some dish soap (maybe 1 tablespoon) with water in a spray bottle. Spray a section with the soapy water and then rub it down with the clay. This is a very mild abrasive which will remove contaminates, tar, bugs, etc and give you smooth clean paint. Wash car after.
  3. Use the rubbing compound with the cutting pad everywhere you can. Don't try to get into tight areas or spots where you can't put the pad flush, because you'll shred the foam pad. Do the tough spots by hand with foam pads. Wash the car to remove any residue.
  4. Repeat with the polish pad and polish, same technique as with cutting.
  5. Apply the duragloss to a clean car by hand with the cloth applicators. Use sparingly, then wipe off with microfiber rags.

    You are done! In most environments the duragloss will last 6+ months. If you keep your car protected with it, you won't need to do the cutting/polishing again (or at least, not for a while).

    The trickiest part of the whole process is the compounding and polishing. Here are some helpful videos.

  1. If you have black rubber trim, say around the windows, mirrors, door handles, etc you either need to keep the polisher away from it or put masking tape on top of it. The rubbing compound and polisher will scuff up softer materials like rubber and it will look bad.
  2. When working with the polisher, always turn it off while still on the surface of the car (preferably still moving it) and let it slow down before lifting it off. If you life the polisher off at full speed it might send the polishing pad flying (it's held on with sturdy velcro). When this happens the velcro is basically shot and you're going to need to get a new pad. If you make sure you always turn it off while still in contact with the car, and you don't try to put it on any sharp corners or narrow areas where you can't get good flat pressure across the whole pad, you should be able to do the entire car with a single pad.
u/anewatrophy · 9 pointsr/AutoDetailing

If you are planning to detail for the long term, I'd suggest investing in some bulk / concentrated products rather than the consumer-grade & Ultimate Meguiar's line.

I've tried to break down the supplies I'd suggest. Of course, don't just throw out your existing supplies. Use them up and then get the concentrates / bulk.

Note: There's no need to get everything in this list. Just get what you need. There's also cheaper alternatives to several of the products, and probably cheaper sites than those in my links. Some of the products I use because I want to support the manufacturer and/or because I trust the manufacturer. Use what you like and use it often. :)

 

Dust, light bug gut, and light bird bomb removal / lube

u/[deleted] · 7 pointsr/AutoDetailing

Apply the wax by hand. Use this:
https://www.amazon.com/Meguiars-X3070-Soft-Foam-Applicator/dp/B0009IQZPW

To buff the wax off, use this:
http://www.theragcompany.com/everest-800-16-x-16-ultra-plush-microfiber-towel/


Sorry for formatting. I've gone mobile http://m.youtube.com/watch?v=4u2gPCtlAaw

u/Gad001 · 3 pointsr/AutoDetailing

The second bucket is a "rinse" bucket. It is used to clean the dirt off your mitt from the dirt it encounters on your car. It contains just water, and you rub your mitt on the grit guard to get all the dirt and grime off off it. Then I typically ring it out and put it into my "wash" bucket. This bucket contains the actual car wash, I run the mitt along the grit guard and then ring it a bit and use it on the car again.
This video will provide a little insight into the process.

As far as applicator pads go, it's best to go with a foam applicator when it comes to applying wax. The reason for this is simply because a foam applicator is going to evenly distribute the wax and not provide any abrasiveness against the surface of your paint. These pads by Meguiar's should do the trick. I personally use Pinnacle Polyfoam pads from AutoGeek.net, but these are probably the same thing, they just have the Meguiar's logo.

I would recommend not using a pad for different applications. Keep one pad for wax, one for sealant, etc. The foam pads I linked can be used for sealant and wax.

However, for compound, I would go with a microfiber applicator if you are going to do it by hand. You may not get stellar results this way, but it may work, I personally have never tried it. The reason for microfiber pads here is because they offer a little more abrasiveness against your paint as opposed to the foam applicators. These may do the trick if you want to apply compound and polish by hand.

u/Liquidretro · 3 pointsr/AutoDetailing

A microfiber or foam applicator pad is what you should probably use.

http://www.amazon.com/Meguiars-X3070-Soft-Foam-Applicator/dp/B0009IQZPW/ref=sr_1_1?ie=UTF8&qid=1407524279&sr=8-1&keywords=meguiars+applicator+pad
http://www.amazon.com/Meguiars-X3080-EvenCoat-Applicator-Pads/dp/B0009IQZQG/ref=sr_1_3?ie=UTF8&qid=1407524279&sr=8-3&keywords=meguiars+applicator+pad

Since your just starting out this might be a good kit http://www.amazon.com/Meguiars-G3300-Brilliant-Solutions-Restoration/dp/B004EB12FS/ref=sr_1_13?ie=UTF8&qid=1407524279&sr=8-13&keywords=meguiars+applicator+pad

Depending on your budget and how much you see washing by hand etc, you might look at /u/TheRagCompany microfibers. They are really liked here, I just got mine and are going to try them out tonight.

Make sure to read up on good technique on the wash and correction so you don't introduce any more scratches etc.

u/pbs094 · 2 pointsr/AutoDetailing

Wash then clay then wax. I like to use a foam applicator pad like this.

A microfiber will work but you may end up absorbing more into the towel than actually applying it onto the car

u/edetailing · 2 pointsr/AutoDetailing

Sure!

Foam Applicator 1

Foam Applicator 2

Microfiber Applicator these also come in packs of two

u/Citecla · 2 pointsr/AutoDetailing

Hey man, what an awesome job!
I am preparing to do my first detail by hand too...just wanted to get your ideas. Which pads did you use for the ultimate compound? Any of these you recommend? http://www.amazon.com/gp/product/B0009IQZQG/ or http://www.amazon.com/Meguiars-HiTech-Applicator-Pad-Pack/dp/B0009IQZPW


Did you switch pads on each of those steps (ie, compound, polish, wax..)

I'm thinking to:

  1. Wash + Dry
  2. Clay Bar + Dry
  3. Compound
  4. Polish
  5. Wax

    Is there any breaks in between any of those processes? Or can I do it one after the other consecutively.

    Thanks buddy :):)
u/Ellsworthless · 2 pointsr/AutoDetailing

these are the pads

Also the pack came with two microfiber towels so I'll use those on windows then.

u/chriskmee · 2 pointsr/subaru

The first thing I would try is this:

Meguiar's Ultimate Compound

Meguiar's X3070 Soft Foam 4" Applicator Pads

Meguiar's X2020 Supreme Shine Microfiber Towels

All 3 of those together is under $20 (need to spend $25 since one is an add on item). This stuff is amazing for scratches and paint in general. While it won't make your car showroom ready, it will make it look much better and is totally worth the $20.

Essentially what you do is first make sure the area is clean, then apply the compound to the pad and rub the compound on your car using circular motions. After you do that for a minute or two, use the towel to remove the compound form the car.

u/caseyls · 2 pointsr/AutoDetailing

The clay kit says it comes with some clay lube, but thanks for the tip!

Foam applicators like this: http://www.amazon.com/Meguiars-X3070-Soft-Foam-Applicator/dp/B0009IQZPW/ref=sr_1_1?ie=UTF8&qid=1395465318&sr=8-1&keywords=foam+applicator?

And would I use the mitt in place of all the microfiber towels or just in some cases?

Thanks!

u/trollster4 · 1 pointr/AutoDetailing

Your list looks good, but is lacking a few item IMO:

http://www.amazon.com/Meguiars-X3002-Microfiber-Wash-Mitt/dp/B000RXKR6M/ref=sr_1_1?s=automotive&ie=UTF8&qid=1396913798&sr=1-1&keywords=microfiber+wash+mitt The mitt you listed should be fine, but I use these. I have 3 of them and it's good to have more than one lying around in case one gets too dirty during the wash. I like to use a different one for the bottom of my car anyway.

I'd get at least one more pack of those Chemical Guys microfiber towels. The more the better.

I use Sonax Full Effect Wheel Cleaner. http://www.amazon.com/Sonax-230200-755-Wheel-Cleaner/dp/B003UT3S6Q/ref=sr_1_1?s=automotive&ie=UTF8&qid=1396914006&sr=1-1&keywords=sonax+full+effect+wheel+cleaner It's a bit pricey but it's very effective at removing brake dust.

For applying the wax, you'll need an applicator pad http://www.amazon.com/Meguiars-X3070-Soft-Foam-Applicator/dp/B0009IQZPW/ref=sr_1_1?s=automotive&ie=UTF8&qid=1396914054&sr=1-1&keywords=foam+applicator+pad