Reddit Reddit reviews Neiko 30252A Water and Oil Separator for Air Line, 1/4" NPT Inlet and Outlet, 90 psi

We found 4 Reddit comments about Neiko 30252A Water and Oil Separator for Air Line, 1/4" NPT Inlet and Outlet, 90 psi. Here are the top ones, ranked by their Reddit score.

Tools & Home Improvement
Power Tool Parts & Accessories
Air Tool Parts & Accessories
Air-Compressor Accessories
Power & Hand Tools
Neiko 30252A Water and Oil Separator for Air Line, 1/4
Eliminates water, oil, dust, and particles in air line from air compressorUniversal 1/4-inch NPT inlet and outlet design connects air line with pneumatic air tools and spray guns; max operating air pressure is 90 psiStops water vapor and particles from entering pneumatic tools to extend tool lifeCatches water vapor and oil particles from entering spray guns to preserve tool life and provide a cleaner paint jobRust-proof aluminum housing and brass fittings provide additional tool durability
Check price on Amazon

4 Reddit comments about Neiko 30252A Water and Oil Separator for Air Line, 1/4" NPT Inlet and Outlet, 90 psi:

u/slap- · 5 pointsr/Cerakote

I bought everything to do it at home because it was cheaper than having a few rifles done by other people. And I like learning new things and doing it myself.

$120 Benchtop Blast Cabinet

$45 50lbs Aluminium Oxide blast media

$40 Dewalt Touch-up Spray gun

$8 Oil/Water Separator

$18 3M Respirator

$8 Powder Free gloves

$14 5ml Glass syringe for easily measuring small amounts of H-Series catalyst. Not necessary but nice. (Grainger.com)

$20 Gallon of Acetone (hardware store)

$30 for misc hoses/fittings

$$$ Container for soaking parts in acetone. I use a 50cal ammo can for almost everything

$$$ Oven for curing if using H-series. I use an old large toaster oven.

$$$ Air compressor with regulator (I already had this)

$$$ Cerakote (plus mesh strainer, graduated cylinder, tape, etc)

​

$300 not including the compressor, Cerakote or oven.

​

Definitely buy extra Cerakote to practice with and learn how to adjust the spray gun. I practiced on some old tools and a rusty vise that I had. I now have a Stormtrooper White vise on my workbench.

​

u/DJ_Skryblz · 1 pointr/gpumining

You really should have an inline filter on your air line.

https://www.amazon.com/gp/product/B002GQ3SUA/ref=s9_acsd_topr_hd_bw_b3jQpjX_c_x_w?pf_rd_m=ATVPDKIKX0DER&pf_rd_s=merchandised-search-4&pf_rd_r=QZVN29F2X7P526SCZ3TT&pf_rd_t=101&pf_rd_p=dc68059f-0cd4-554c-860c-419946e51f9b&pf_rd_i=3419729011

u/champ_town · 1 pointr/Trackdays

Talk with your local paint supplier on that particular brand's processes - but you will likely want/need to reprime it so it is sure to stick (and the primer you want to be compatible with the paint you use). I know the primer I used, you wanted to lay paint on it within 48 hours or so for best adhesion.

  • After initial sanding, make sure to wipe down with a cheese cloth, then follow up with a solvent on a clean rag (paint thinner, mineral spirits, etc)

  • Your time between coats will be specified by the paint you buy, it'll probably 30-60 minutes. Then the clearcoat is probably the one you'll have to wait a day to put on

  • Again talk to your supplier, but usually the fine grit sanding is done between clear coats, then buff at the end

  • You will find there is more to buy than just "paint" - usually you need the paint and a catalyst, plus a thinner. You will probably leave the store with 8 cans of stuff

  • The big thing to think about after you setup your booth - how are you going to hold/hang all the pieces? Can be tricky. Hanging works ok for some pieces but they tend to move around (just the air coming out of the paint gun can blow a piece around). Make sure to set each piece such that you can get to all sides and you aren't spraying at a different piece behind it

  • Buy a drier

  • Get all the other stuff with your paint gun, like a holder, mixing cups, strainers, etc.

  • Buy a quality respirator

    It takes some practice to get the amount of paint correct, as well as dialing in the gun (watch some Youtube videos). There is a somewhat fine line between putting the final coat on too light and it showing up dry, or all of a sudden you put too much on and you have a run. Don't forget to clean the gun thoroughly after each use.

    Final advice? Don't sweat the imperfections, it's a track bike and we aren't pro racers. Also accept that your first full paint job or at least the first couple pieces you do will probably not look great as you learn how to setup the gun and control how much paint to lay down.
u/GideonD · 1 pointr/buildapc

Just pin the fan with something to keep it from spinning. Put a pen through it. As for the compressor itself you need to be careful with that. Compressors tend to condense moisture in the tanks. I keep mine stored with the drain valve open so anything that condenses in is during times it's not in use drains out. Even that isn't a sure thing though so before I even considered using it for a purpose like this I installed an oil/water separating filter in line to make sure any leftover moisture got filtered out. They are not expensive and a good thing to have as they protect your air tools from corrosion as well. A desiccant dryer works even better, but is a lot more expensive. Here is what I have on mine. https://www.amazon.com/Neiko-30252A-Water-Separator-Outlet/dp/B002GQ3SUA/ref=pd_sim_469_2?_encoding=UTF8&psc=1&refRID=R9QATQYGZXACBZ21C5J9